aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/image/generic-tp-link.mk
Commit message (Collapse)AuthorAgeFilesLines
* ath79: fix SUPPORTED_DEVICES for TP-Link TL-WR1043ND v3Adrian Schmutzler2019-11-111-1/+1
| | | | | | | | | In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2: tl-wr1043nd-v2 Fix SUPPORTED_DEVICES for v3 in ath79 accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the TP-LINK CPE220 V3Andrew Cameron2019-11-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 2.4GHz N based AP Specifications: SoC: Qualcomm Atheros QCA9533 (650MHz) RAM: 64MB Storage: 8 MB SPI NOR Wireless: 2.4GHz N based built into SoC 2x2 Ethernet: 2x 100/10 Mbps, integrated into SoC Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This also applies some minor changes to the common DTSI: - use &wmac for label-mac-device, as this one is actually set up in common DTSI - move &eth0 to parent DTSI - fix several leading spaces, added/removed newlines Signed-off-by: Andrew Cameron <apcameron@softhome.net> [DTS style fixes/improvements, updated commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link WBS210 v2Bernhard Geier2019-11-031-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with two Ethernet ports based on Atheros AR9344 The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm instead of 12 dBm) and two antenna connectors instead of built-in antennas. Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP: 192.168.0.100 Stock device TFTP adress: 192.168.0.254 The TP-Link WBS devices use the same GPIOs as the CPE devices, except for the link4 LED. For this one, WBS devices use "2", while CPE devices use "16". (Tested on WBS210 v2) Signed-off-by: Bernhard Geier <freifunk@geierb.de> [added comment about GPIO] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WR1045ND v2Rasim Kalimullin2019-11-031-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9558 Soc - 720/800 (CPU/DDR) - 1x 10/100/1000 Mbps WAN Ethernet - 4x 10/100/1000 Mbps LAN Ethernet - 64 MB RAM (DDR2) - 8 MB FLASH - QCA9558 2.4 GHz 802.11bgn - 1x USB 2.0 Flash instruction WebUI: Download *-factory.bin image, rename to tp_firmware.bin and upload it via the firmwary upgrade function of the stock firmware WebUI. Tftp: Rename OpenWRT or original firmware to wr1045v2_tp_recovery.bin and Change your computer ip in 192.168.0.66 and subnet mask in 255.255.255.0. Router will obtain IP 192.168.0.86 for a few seconds while loading, when reset button pressed at power On. Signed-off-by: Rasim Kalimullin <neutrino.vm@gmail.com> [rebased onto base-files split] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove kmod-usb-core from DEVICE_PACKAGESAdrian Schmutzler2019-10-061-20/+20
| | | | | | | | | | | | | | | | | | | This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: sort device definitions in image/*Adrian Schmutzler2019-09-211-106/+106
| | | | | | | | | | | This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C59v2Keith Maika2019-09-161-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ath79 support for Archer C59v2, previously supported by ar71xx. TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* ath79: add support for TP-Link WDR3500 v1Adrian Schmutzler2019-09-031-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: AR9344 CPU: 560 MHz Flash: 8 MiB RAM: 128 MiB WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9300 5GHz 802.11an Ethernet: AR934X built-in switch, WAN on separate physical interface USB: 1x 2.0 Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to wdr3500v1_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [removed stray newline] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove SUPPORTED_DEVICES for TP-Link Archer D50 v1Adrian Schmutzler2019-08-151-1/+0
| | | | | | | This device has not been supported in ar71xx, so there is no need for an explicit SUPPORTED_DEVICES entry. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE220 v2Adrian Schmutzler2019-08-071-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | This seems to be identical to CPE210 v1 despite having removable antennas. Specifications: * SoC: Qualcomm Atheros AR9344 (560 MHz) * RAM: 64MB * Storage: 8 MB * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE510 v1Adrian Schmutzler2019-08-071-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with two Ethernet ports based on Atheros AR9334 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 2T2R 5 GHz - 13 dBi built-in antenna - Power, LAN0, LAN1 green LEDs - 4x green RSSI LEDs Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Based on the work of Paul Wassi <p.wassi@gmx.at> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE210 v1Adrian Schmutzler2019-08-071-0/+12
| | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros AR9344 (560 MHz) * RAM: 64MB * Storage: 8 MB * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: create common definition tplink-loader-okliAdrian Schmutzler2019-08-071-18/+3
| | | | | | | The loader-okli is shared by several TP-Link CPExxx devices, so give it its own definition to prevent too much code duplication. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C60 v2Adrian Schmutzler2019-07-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 ...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C60 v1Adrian Schmutzler2019-07-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 ...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE510-v2/v3Andrew Cameron2019-07-181-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link RE355 v1 and RE450 v1Christoph Krapp2019-07-171-0/+27
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: Qualcomm Atheros QCA9558 RAM: 64/128MiB Flash: 8MiB SPI-NOR Wifi: - 2.4GHz: 3T3R (QCA9558) - 5GHz: 3T3R (QCA9880) LAN: 1x 10/100/1000 Mbps UART: - TP1: Tx - TP2: Rx - TP3: Gnd - TP4: 3v3 Flash instructions: Flash factory image through stock firmware WEB UI. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: fix missing DEVICE_VENDOR for some devicesChen Minqiang2019-07-101-0/+1
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ath79: increase kernel partition size for CPE610v1Andrew Cameron2019-07-071-1/+4
| | | | | | | | | Increase the Kernel partition to address the issue discussed here https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5 Switch Back to the okli Loader to support increased partition size Signed-off-by: Andrew Cameron <apcameron@softhome.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
* ath79: split DEVICE_TITLE in multiple variablesPaul Spooren2019-07-041-32/+64
| | | | | | | | | | | | | | This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: Use -v1 suffix for TP-Link WDR3600/4300Adrian Schmutzler2019-07-031-6/+6
| | | | | | | | | | | | | | | In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have been used while most other TP-Link devices include the revision. Although there actually is only one major revision of these devices, they bear the revision on their bottom (v1.x). TP-Link also refers to the devices as V1 on its web page. This patch thus adds -v1 to both so it is more consistent with other devices and with what you would expect from reading the on-device sticker and the support pages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE610-v1Andrew Cameron2019-06-241-0/+11
| | | | | | | | | | | | | | | | | | | | | TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: Add SUPPORTED_DEVICES for Archer C7 v1/v2Adrian Schmutzler2019-06-151-0/+2
| | | | | | | | The identifier for both devices is "archer-c7" on ar71xx, set here: https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L348 https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L511 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-101-0/+11
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer D50 V1Davide Fioravanti2019-05-181-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer D50 v1 is a dual-band AC1200 router + modem. The router section is based on Qualcomm/Atheros QCA9531 + QCA9882. The "DSL" section is based on BCM6318 but it's currently not supported. Internally eth0 is connected to the Broadcom CPU. Router section - Specification: CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB) RAM: 64 MB (DDR2) Flash: 8 MB (SPI NOR) Wifi 2.4GHz: QCA9531 2T2R Wifi 5GHz: QCA9982 2T2R 4x 10/100 Mbps Ethernet 8x LED, 3x button UART header on PCB Known issues: DSL not working (eth0) (WIP) UART connection --------------- J2 HEADER (Qualcomm CPU) . TX . RX . GND O VCC J16 HEADER (Broadcom CPU) O VCC . GND . RX . TX The following instructions require a connection to the J2 UART header. Flash instruction under U-Boot, using UART ------------------------------------------ 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Initramfs instruction under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin bootm 0x81000000 Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616 4. Double check the .mod file size. It must be 7995392 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed default-state = "off", it's already the default, added pcie node, fixed typo]
* ath79: Add support for TP-Link TL-WR1043N v5Adrian Schmutzler2019-05-181-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9563 at 775 MHz - 64 MB RAM Zentel A3R12E40CBF-8E - 16 MB flash Winbond W25Q128FVSG - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. It also has different partitioning scheme. The software is more in line with the Archer series in that it uses a nested bootloader scheme. (This has been adapted from the OpenWrt Wiki page) <https://openwrt.org/toh/tp-link/tl-wr1043nd> Installation on HW rev.5: Factory firmware can be installed via the WEB interface. Alternatively, it is also possible to use a TFTP server for recovery purposes: - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin - Set static IP of your PC to *192.168.0.66* - Router will obtain IP 192.168.0.86 for a few seconds while loading, when reset button pressed at power On. And finally, there's always u-boot access through the UART. For information visit the wiki. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworked commit message]
* ath79: Move TL-WR1043ND v1 definition to companionsAdrian Schmutzler2019-05-181-10/+10
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add TP-Link WR842N v3Sven Roederer2019-04-131-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link WR842N v3 which is already supported on ar71xx target (0b45bec22c59cc6e6b2fa71dc9a88386c5587132). Specification: * SoC: QCA9533 ver 2 rev 0 * 16 MB Flash (gd25q128) * 64 MB RAM * 1 WAN 10/100 MBit/s (blue connector) * 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors) * Atheros AR9531 (2,4GHz, two fixed antennas) * USB * Reset / WPS button * WiFi button (rf kill) * 8 green leds; 1 red/green led * serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed) Installation: * flash via vendor WebUI (the filename must not exceed certain length) * sysupgrade from installed OpenWrt (also ar71xx) Thanks to Holger Drefs for providing the hardware Tested-by: @kofec (github) Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ath79: Utilize tplink-safeloader definitionAdrian Schmutzler2019-04-061-17/+3
| | | | | | | | | | | | | | | | | Currently, tplink-safeloader definition is only used a base for another common definition. This patch adjusts tplink-safeloader so it can be actually used for some targets in generic-tp-link.mk. This patch is cosmetic except for the order of "check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged for the tplink_re350k-v1 . Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's extra IMAGE/sysupgrade.bin rule]
* ath79: Add support for TP-Link CPE210 v2Adrian Schmutzler2019-04-021-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This is based on the support patch for the identical CPE210 v3 by Mario Schroen <m.schroen@web.de>. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for TP-Link CPE210 v3Mario Schroen2019-04-021-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros QCA9533 (650MHz) * RAM: 64MB * Storage: 8 MB SPI NOR * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Thanks to robimarko for the work inside the ar71xx tree. Thanks to adrianschmutzler for deep discussion and fixes. Signed-off-by: Mario Schroen <m.schroen@web.de> [Split into DTS/DTSI, read-only config partition in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename, light subject touches] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add TP-Link TL-WR710N v1Marcin Jurkowski2019-03-241-0/+10
| | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link TL-WR710N v1 router. CPU: Atheros AR9331 400MHz RAM: 32MB FLASH: 8MiB PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN WiFi: Atheros AR9331 1x2:1 bgn USB: ChipIdea HDRC USB2.0 LED: SYS BTN: Reset Sysupgrade from `ar71xx` works without glitches. Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0` respectively, what's consistent with `ar71xx` target. Wireless radio path is automatically upgraded from `platform/ar933x_wmac` to `platform/ahb/18100000.wmac`. Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
* ath79: add support for TP-Link RE350K v1Piotr Dymacz2019-03-111-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for TP-Link Archer C5 v1Bart Lauret2019-02-281-0/+10
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C5 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 16 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-BR4A - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500> Signed-off-by: Bart Lauret <bblauret@gmail.com>
* ath79: fix support-list for TP-Link WDR3600David Bauer2019-02-261-1/+1
| | | | | | | | | | | | The TP-Link WDR3600 shares the same machine-code in the ar71xx target, thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list metadata to allow non-forced sysupgrades from ar71xx to ath79. With this, it is possible to flash a WDR4300 image on the WDR3600. It is no problem however, as the only difference is the 5GHz WiFi chip which has 3SS instead of 2SS. Both work with either image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: rename TP-LINK to TP-LinkPaul Wassi2019-02-141-22/+22
| | | | | | Remove inconsistencies in the vendor's name. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for TP-LINK Archer C7 v4Oldřich Jedlička2019-02-051-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the Qualcomm/Atheros QCA9561 SoC + QCA9880. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
* ath79: add support for TP-Link Archer C2 V3 (AC900)Skirmantas Lauzikas2019-01-271-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the TP-link Archer C2 V3 (AC900). Specifications: - CPU: QCA9563 750Mhz - Ram: 64MB (DDR2) - Flash: 8MB (SPI NOR) - Ethernet: 5x 10/100/1000 - Wifi: QCA9563 bgn + QCA9887 an+ac - 9x Leds, 2x buttons Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin via the router Web interface and flash as normal firmware update. Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reorder entries, fix trailing whitespace in dts, add firmware partition compatible string, remove led default off states, use default on state for system led, reuse tplink-safeloader-uimage image build recipe, squash with dynamic partitioning commit, reword commit message, add installation instructions] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: add support for TP-Link Archer C6 v2Georgi Vlaev2018-12-311-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath79: Add support for TP-Link WR810NPaul Wassi2018-12-311-0/+17
| | | | | | Device specifications given in b23b0fb28b760ce66a8f93d4681c8bd300d75d30 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for TP-Link Archer C7 v5TOCK Chiu2018-12-271-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for TP-Link Archer C7 v5, leveraging most effort from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5 but with a different flash layout. Specification: - QCA9563 SoC (750 MHz) - 128 MiB of RAM (DDR2) - 16 MiB of flash (SPI) - 5x 1 Gbps Ethernet (1x WAN + 4x LAN) - 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880 - 10x LED, 2x button - UART header on PCB Flash instructions: 1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin via web interface. Flash instructions using TFTP recovery: 1. Plug PC to one of the LAN ports 2. Set PC to fixed IP address 192.168.0.66 3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in TFTP root directory 4. Turn on the router with the reset button pressed for about 15 secs 5. Release the button and wait about 150 secs to complete flashing Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
* ath79: add support for TP-Link Archer A7Karl-Felix Glatzer2018-12-171-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
* ath79: add support for TP-Link TL-WR842N/ND v1 routerMarcin Jurkowski2018-12-151-0/+9
| | | | | | | | | | | | | | | | | | This ports support for TP-Link TL-WR842N/ND v1 from ar71xx. CPU: Atheros AR7241 400 MHz RAM: 32 MiB FLASH: 8 MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9287 LED: SYS, WiFi, LAN, WAN, 3G, QSS BTN: WiFi, Reset/WPS AR71xx target used "tl-mr3420" as board id so force flag is needed if upgrading from old target. Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
* ath79: remove duplicate image build variablesMathias Kresin2018-12-061-1/+1
| | | | | | | Remove image build variables which are set to the same value as the default image build recipe. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for Archer C58/C59 v1David Bauer2018-11-261-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Archer C58 v1 and C59 v1, previously supported in the ar71xx target. CPU: Qualcomm QCA9561 RAM: 64M (C58) / 128M (C59) FLASH: 8M (C58) / 16M (C59) WiFi: QCA9561 bgn 3x3:3 QCA9888 nac 2x2:2 LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS Only C59: USB BTN: WPS, WiFi, Reset Installation ------------ Via Web-UI: Update factory image via Web-UI. Via TFTP: Rename factory image to "tp_recovery.bin" and place it in the root-dir of your tftp server. Configure to listen on 192.168.0.66. Power up the router while holding down the reset-button. The router will flash itself and reboot. Note: For TFTP, you might need a switch between router and computer, as link establishment might take to long. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Add support for TP-Link TL-WR842N-v2Robert Marko2018-10-071-0/+10
| | | | | | | | | | | | | | | | | | | | This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79. This is a low cost model with following specs: CPU: Atheros AR9341 SoC RAM: 32 MB DDR1 Flash: 8 MB NOR SPI Switch: Internal AR9341 5 port 10/100 Mbit Ports: 5x 10/100 Mbit(1x WAN, 4x LAN) USB: 1x USB2.0 WLAN: 2.4 GHZ AR9341 Installation: Simply flash the factory image through stock firmware WEB UI. Signed-off-by: Robert Marko <robimarko@gmail.com>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-261-3/+3
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* ath79: add support for TP-Link Archer C7 v1Christian Lamparter2018-08-191-0/+9
| | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v1 is a dual band router based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: - 720 MHz CPU - 128 MB of RAM (Various chips) - 8 MB of FLASH (Various chips) - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi - minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!) - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch) - 10x LEDs, 2x software buttons For further informwation on the device, visit the wiki: <https://openwrt.org/toh/tp-link/archer-c7-1750> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: drop tl prefix for TP-Link RE450 v2Peter Lundkvist2018-08-131-2/+2
| | | | | | | | This router is called RE450 and the tl prefix was used to identify it as a TP-Link device. Drop the tl prefix since we now have tplink in dts and device name. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* ath79: add support for TP-Link TL-WDR4900 v2Chuanhong Guo2018-08-111-0/+9
| | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 8 MB - RAM: 128 MB - Ethernet: AR8327N with 5 GE ports. - Wireless radio: QCA9558 for 2.4G and AR9580 for 5G. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 14:38:36 +0000