| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.
SoC: Qualcomm / Atheros QCA9533-BL3A
RAM: 64 MB DDR2
Flash: 16 MB SPI NOR
Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS: 1x via a SPI controller (not yet supported)
Buttons: 1x Reset
Serial: 1x (only RX and TX); 115200 baud, 8N1
Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
(Needs RSA signed images, for details see PR#1958)
The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND
Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
key to stop autoboot` is displayed. Note: Pressing space multiple
times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
image to the server.
- Set the U-Boot server IP with
setenv serverip 192.168.1.100
- Load the flash image to RAM with
tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
erase 0x9f050000 0x9ffaffff
- Write the new flash content with
cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
reset
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN: QCA988X
Ports: 1x GbE
Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.
Serial flashing:
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Flashing through factory firmware:
1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
Thanks to @cybermaus for testing!
Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Support for the Nanostation M (XW) was added in 40530c8eb with board
name "nanostation-m-xw". The current image for the "Nanostation M"
uses "nano-m" as the board name.
This commit renames it to the full product name as it's used by all
other boards. The legacy boardname of the ar71xx target is added
via SUPPORTED_DEVICES to ease switching to ath79 target.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[touch-ups on the commit message, removed subject remains]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In PR [1] introducing initial support for Ubiquiti RouterStation boards,
Mathias Kresin suggested to replace the combined sysupgrade image with
tarball generated by sysupgrade-tar.sh. This would simplify deployment
of sysupgrade as the kernel size (needed to update FIS partition) could
be simply calculated on the fly instead of reading value from combined
image header. Unfortunately this would break sysupgrade compatibility
between ar71xx image and ath79 image. Therefore this commit creates
migration path to use new sysuprade image, it adds code to accept both
of them at this moment. The plan is to keep it until new stable version
is released. Then the image recipe should be changed to new format and
compatibility code for old image removed.
1. https://github.com/openwrt/openwrt/pull/1237
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN: 2.4/5 GHz
UART: 1 UART
LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
| |
|
|
|
|
|
| |
Since commit 61b5b4971e7 ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
| |
Remove image build variables which are set to the same value as the
default image build recipe.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Indoor low-power router with 2.4 GHz radio
CPU: Atheros AR7241 rev 1
RAM: 32 MB
Flash: 8 MB NOR SPI
Switch: Atheros AR7240
Ports: 1x WAN, 4x LAN 10/100 Ethernet
WLAN: Atheros AR9285 (2.4 GHz)
USB: 1x USB2 host port
Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.
UART settings: 115200, 8N1
LEDs
+--------------------------
|
|
|
|
|
|
|
|
VCC | x x
RX | * x
| x x
| x x
TX | * x
GND | * x
|
|
|
|
+--------------------------
ETHERNET PORTS
Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3735964 bytes
Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions
A) Serial console, U-Boot and TFTP
1. Connect to serial header J1 on the PCB
2. Power on device and enter U-Boot console
3. Set up TFTP server serving an OpenWrt initramfs build
4. Load initramfs build using the command tftpboot in the U-Boot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs OpenWrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
B) Experimental factory image flashing over SSH from airOS v6.1.7
1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
no other airOS version is currently supported
2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
3. cd ubnt-bullet-m2hp-openwrt-flashing
4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Ports: 1 GbE port (PoE in)
WLAN: 5 GHz QCA899X (PCI)
The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).
Installation procedure is the same as the NanoStation [loco] AC:
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The image build code for the Ubiquiti Nanostation AC series adds the
factory image as to be build image. The same is already done by an
included recipe which results into an expanded IMAGE variable of:
IMAGES = sysupgrade.bin factory.bin factory.bin
The build system doesn't like these duplicates and issues the following
warning:
Makefile:82: warning: overriding recipe for target...
Get remove the duplicate factory image to get rid of the warning.
Fixes: 5736af8024be ("ath79: Add support for Ubiquiti NanoStation AC loco")
fa3c2676ab0c ("ath79: Add support for Ubiquiti Nanostation AC")
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Switch: QCA8334
Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough)
WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342
Successor to the old NanoStation M5 with AC wireless.
The integrated QCA899X is a Ubiquiti branded part with modified vendor and
product id (0777:11ac9).
Serial
Serial settings: 115200, 8N1
* = plated through hole
0 = nylon screw
[Top of device]
+--------------------------+
| [label] |
| 0 |
| 0 |
| [ubnt] |
| [logo] 3V3 * |
| TX * |
| RX * |
| GND * |
| |
| * |
| * |
| * |
| * |
| 0 |
| 0 |
| |
| |
Installation
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Atheros AR9342, 16 MB flash, 64 MB RAM
Successor to the old NanoStation M5 loco with AC wireless.
Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti
branded and customized QCA988X with vendor id 0777 and device id 11ac for
AC wireless.
Installation
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
|
| |
|
|
|
|
|
|
| |
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
|
| |
|
|
|
|
|
|
| |
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM family.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other
.dts files that utilize it, ar7161_ubnt_routerstation.dts and
ar7161_ubnt_routerstation-pro.dts.
The modifications to generic-ubnt.mk, config-default, and base-files
necessary for image generation, parsing RedBoot FIS partitions, network
configuration, and sysupgrade are also included.
This reintroduces vital bits from platform_do_upgrade_combined() and its
supporting functions to /lib/upgrade/platform.sh, which were previously
removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79:
sysupgrade: drop unused platform checks". The new function is called
"routerstation_do_upgrade" and will *only* work for the RouterStation
series of boards. It does however retain the ability to downgrade (e.g.
from master -> 17.01.x using sysupgrade -F).
All hardware is functional including the AR8216 switch (for the Pro),
wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button,
and LED.
Switch and LAN/WAN configuration is the same as it is with the
equivalent ar71xx targets. MAC addresses are assigned based upon the
content stored in the RedBoot config partition.
Flashing via both sysupgrade and TFTP has been confirmed to work. Also,
the initramfs images are now raw .bin files instead of being wrapped in
a uImage (as they currently are in ar71xx), which makes them bootable
with RedBoot.
One notable difference to ar71xx is the inclusion of the RedBoot
"fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in
DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD
parser’s DT binding, whose proper usage is mutually exclusive to
defining a separate fixed-partitions node for "RedBoot config". This
config partition contains the board's base MAC address. The lack of a
hard-coded flash location means that the mtd-mac-address property cannot
be used in the .dts, so instead fconfig is used to read the MAC
addresses from flash in userspace during first boot.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
|
| |
|
|
|
|
|
|
|
| |
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
|
| |
|
|
|
|
|
|
|
| |
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
|
|
|
|
| |
rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
|
| |
|
|
|
|
|
| |
Use a Unifi AC Lite board-/image name consistent with other Ubiquiti
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
| |
|
|
| |
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
|
| |
|
|
|
|
| |
Add metadata to images and make the metdata mandatory.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
|
|
| |
Remove recipes for not yet migrated boards. Drop variables which aren't
required due to the switch to devicetree like boardname.
Drop the legacy image build code. Boards added to this target shouldn't
use the legacy image build code anyway.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
|
| |
Add the SoC compatible to the individual dts files. Rename the dts files
to match the common pattern.
Remove dts files wich aren't used and no image in ar71xx exists.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
| |
Apply ar71xx fix for broken Ubiquiti bootloader to ath79 as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
|
|
|
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.
Signed-off-by: John Crispin <john@phrozen.org>
|
