aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/image/generic.mk
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: add support for Comfast E314N-v2Joan Moreau2019-08-091-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Taken code from https://patchwork.ozlabs.org/patch/884850/ that was never pushed by the author, and adapted to ath79. The Comfast E314N-V2 is a 2.4 GHz 2x2 radio with a built-in directional antenna and a second Ethernet port - very similar to the Ubiquiti NanoStation M2. The Ethernet port features a pass-through PoE capability, enabled or disabled with a slide switch. Specifications : - System-On-Chip: Qualcomm/Atheros QCA9531 - CPU/Speed: 650 MHz - Flash size: 8 MiB - RAM: 64 MiB - 2 Ethernet 1Gbp - 1 reset button - 1 switch to choose PoE from LAN or Wan. 48Vdc - Wifi 2.4 Ghz (b/g/n) - UART inside the box (3.3V, pins marked on the PCB) Firmware can be flashed on these units by the following method: 1.) Apply power to the unit 2.) Immediately AFTER applying power, hold down the reset button 3.) The WAN, LAN, and wireless lights will flash - wait three seconds (three flashes) and then release the button. 4.) After a second, the lights will flutter quickly and the unit will be visible at 192.168.1.1. A web page will be available to enable quick and simple uploading and flashing of firmware. During the boot process, these units also look for a tftp server at 192.168.1.10. If one is present, the firmware can be uploaded as a file called firmware-auto.bin Signed-off-by: Joan Moreau <jom@grosjo.net> [wrapped commit message - fix commit title capitalization] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for PISEN WMB001NChuanhong Guo2019-08-081-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: AR9341 - RAM: 64M - Flash: 16M - Ethernet: 1 * FE port - WiFi: ar934x-wmac - Sound: WM8918 DAC 1 * 3.5mm headphone jack 2 * RCA connectors for speakers 1 * SPDIF out - USB: 1 * USB2.0 port Flash instruction: Upload generated factory image via vendor's web interface. Notes: A. Audio stuff: 1. Since AR934x, all pins for peripheral blocks can be mapped to any available GPIOs. We currently don't have a PCM/I2S driver for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio node. This should be moved into I2S node when a PCM/I2S driver is available. 2. The i2c-gpio node is for WM8918. DT binding for it can't be added currently due to a missing clock from I2S PLL. B. Factory image: Image contains a image header and a tar.gz archive. 1. Header: A 288 byte header that has nothing to do with appended tarball. Format: 0x0-0x7 and 0x18-0x1F: magic values 0x20: Model number string 0xFC: Action string. It's either "update" or "backup" 0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B Firmware doesn't care about the rest of the header as long as checksum result is correct. The same header is used for backup and update routines so the magic values and model number can be obtained by generating a backup bin and grab values from it. 2. Tarball: It contains two files named uImage and rootfs, which will be flashed into corresponding mtd partition. Writing a special utility that can only output a fixed binary blob is overkill so factory image header is placed under image/bin instead. C. LED The wifi led has "Wi-Fi" marked on the case but vendor's firmware used it as system status indicator. I did the same in this device support patch. D. Firmware Factory u-boot is built without 'savenv' support so it's impossible to change kernel offset. A 2MB kernel partition won't be enough in the future. OKLI loader is used here to migrate this problem: 1. add OKLI image magic support into uImage parser. 2. build an OKLI loader, compress it with lzma and add a normal uImage header. 3. flash the loader to where the original kernel supposed to be. 4. create a uImage firmware using OKLI loader. 5. flash the created firmware to where rootfs supposed to be. By doing so, u-boot will start OKLI loader, which will then load the actual kernel at 0x20000. The kernel partition is 2MB, which is too much for our loader. To save this space, "mtd-concat" is used here: 1. create a 64K (1 erase block) partition for OKLI loader and create another partition with the left space. 2. concatenate rootfs and this partition into a virtual flash. 3. use the virtual flash for firmware partition. Currently OKLI loader is flashed with factory image only. sysupgrade won't replace it. Since it only has one function and it works for several years, its unlikely to have some bugs that requires a replacement. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for D-Link DIR-842 C3Perry Melange2019-08-071-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C3: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
* ath79: add support for D-Link DIR-842 C1Jackson Lim2019-08-051-3/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C1: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [fix whitespace issues] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for ALFA Network AP121FRoger Pueyo Centelles2019-07-311-0/+10
| | | | | | | | | | | | | This commit ports support for the ALFA Network AP121F, a pocket-size router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the ath79 target (it was already supported in ar71xx; see commit 0c6165d2 for more details). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env partition writable] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for D-Link DIR-842 C2Jackson Lim2019-07-241-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-842 C2: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: 2.0 Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim <jackcolentern@gmail.com> [Reword reset-hog comment, fix formatting] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: modify device name of I-O DATA WN-AC1600DGR2INAGAKI Hiroshi2019-07-181-3/+4
| | | | | | | | | | | | | | | | | | | | | | | The hardware of I-O DATA WN-AC1600DGR3 has completely compatibility with WN-AC1600DGR2, so modify the device name of WN-AC1600DGR2 to show the images for DGR2 also support DGR3. Specification of WN-AC1600DGR3: - SoC : Qualcomm Atheros QCA9557 - RAM : DDR2 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : QCA9557 (SoC), 2T2R - 5 Ghz : QCA9880, 3T3R - Ethernet : 5x 10/100/1000 Mbps - Switch : QCA8337N - LEDs/Input : 6x/6x (4x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, GND, TX, RX from ethernet port side - 115200n8 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Trendnet TEW-823DRUPramod Pancha2019-07-181-0/+16
| | | | | | | | | | | | | | | | | | | | | Trendnet TEW-823DRU is a dual-band AC1750 router. The router is based on Qualcomm/Atheros QCA9558 + QCA9880. Specification: 720 MHz CPU 256 MB of RAM 16 MB of FLASH 3T3R 2.4 GHz 3T3R 5 GHz 5x 10/100/1000 Mbps Ethernet Firmware can be flashed from the web interface. Tested on 3 routers with no issues. Signed-off-by: Pramod Pancha <pancha@vill.com> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Bluesocket BSAP1880 boardDaniel Gimpelevich2019-07-171-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for Qihoo C301Chuanhong Guo2019-07-161-0/+12
| | | | | | | | | | | | | | | | Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for devolo WiFi pro 1750xDavid Bauer2019-07-141-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED Power (non-controllable) 1x LED Status (internal) 1x LED LAN (controlled by PHY) 1x LED WLAN BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to external-LED header. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Add missing IMAGE_SIZE for Etactica EG200Adrian Schmutzler2019-07-081-0/+1
| | | | | | | The Etactica EG200 is the only device in ath79 despite nand target that lacks IMAGE_SIZE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Correctly use DEVICE_VARIANT for NETGEAR WNDR3700Adrian Schmutzler2019-07-041-1/+3
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Move DEVICE_VENDOR for NETGEAR to parent definitionAdrian Schmutzler2019-07-041-5/+0
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: split DEVICE_TITLE in multiple variablesPaul Spooren2019-07-041-63/+135
| | | | | | | | | | | | | | This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ath79: add support for 8devices Carambola2 development boardRytis Zigmantavičius2019-06-051-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Atheros AR9331 (400 MHz) - 64 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 1T1R 2.4 Wlan (AR9331) - 2x 10/100 Mbps Ethernet - 3x LEDs, 1x gpio button - 1x USB 2.0, 5V - UART over usb, 115200n8 Upgrading from ar71xx target: - Put image into board: scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \ root@192.168.1.1/tmp/ - Run sysupgrade sysupgrade /tmp/sysupgrade.bin Upgrading from u-boot: - Set up tftp server with sysupgrade.bin image - Go to u-boot (reboot and press ESC when prompted) - Set TFTP server IP setenv serverip 192.168.1.254 - Set device ip from same subnet setenv ipaddr 192.168.1.1 - Copy new firmware to board tftpboot 0x81000000 sysupgrade.bin - erase flash erase 0x9f050000 +${filesize} - flash firmware cp.b 0x81000000 0x9f050000 ${filesize} - Reset board reset Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com> [wrapped long line in commit description, whitespace and art address fix in DTS, keep default lan/wan setup, removed -n in sysupgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for ZBT-WD323Kristian Evensen2019-06-051-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT-WD323 is a dual-LTE router based on AR9344. The detailed specifications are: * AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN). * 128 MB RAM * 16MB of flash(SPI-NOR, 22MHz) * 1x 2.4GHz wifi (Atheros AR9340) * 3x 10/100Mbos Ethernet (AR8229) * 1x USB2.0 port * 2x miniPCIe-slots (USB2.0 only) * 2x SIM slots (standard size) * 4x LEDs (1 gpio controlled) * 1x reset button * 1x 10 pin terminal block (RS232, RS485, 4x GPIO) * 2x CP210x UART bridge controllers (used for RS232 and RS485) * 1x 2 pin 5mm industrial interface (input voltage 12V~36V) * 1x DC jack * 1x RTC (PCF8563) Tested: - Ethernet switch - Wifi - USB port - MiniPCIe-slots (+ SIM slots) - Sysupgrade - Reset button - RS232 Intallation and recovery: The board ships with OpenWRT, but sysupgrade does not work as a different firmware format than what is expected is generated. The easiest way to install (and recover) the router, is to use the web-interface provided by the bootloader (Breed). While the interface is in Chinese, it is easy to use. First, in order to access the interface, you need to hold down the reset button for around five seconds. Then, go to 192.168.1.1 in your browser. Click on the second item in the list on the left to access the recovery page. The second item on the next page is where you select the firmware. Select the menu item containing "Atheros SDK" and "16MB" in the dropdown close to the buttom, and click on the button at the bottom to start installation/recovery. Notes: * RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1 Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for WD My Net N750Ryan Mounce2019-05-271-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9344 RAM: 128MB Flash: 16MiB Winbond 25Q128BVFG SPI NOR 5GHz WiFi: AR9380 PCIe 3x3:3 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Gigabit ethernet via AR8327N switch (green + amber LEDs) 2x USB 2.0 via GL850G hub 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO Known issues: AR8327N LEDs only have default functionality, not presented in sysfs. This is a regression from ar71xx. UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX See https://openwrt.org/toh/wd/n750 for flashing detail. Procedures unchanged from ar71xx. Tested sysupgrade + factory flash from WD Emergency Recovery Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ath79: glinet_gl-ar750s: Add USB power & microSDAlexander Wördekemper2019-05-201-1/+1
| | | | | | | | | The GL.iNet AR750S USB and microSD port is currently not working out of the box. GPIO 7 is used to control the power of the USB port. Add GPIO 7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the microSD port to work. Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
* ath79: add support for Aruba AP-105Chris Blake2019-05-181-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Atheros AR7161-8C1A @ 680 MHz RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR) WI1: Atheros AR9223-AC1A 802.11bgn WI2: Atheros AR9220-AC1A 802.11an ETH: Atheros AR8021-BL1E + PoE LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G BTN: 1 x Reset I2C: AT97SC4303s TPM (needs driver!) CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud Factory installation: - Needs a u-boot replacement. See Wiki for information on how to do a in-circut flash with a SPI-Flasher like a CH314A or flashrom. Wiki page can be found at https://openwrt.org/toh/aruba/aruba_ap-105 - Be careful when dis- and reassembling the device to not squish any of the antenna cables in the process! - Be sure to make a full 16 MiB backup of your device before flashing the new u-boot! This is needed if you ever have interest in reverting back to stock firmware. Not working: - TPM (needs a driver) Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ath79: add support for EnGenius ECB1750sven friedmann2019-05-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - Qualcomm Atheros SoC QCA9558 - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 1x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH) https://fccid.io/A8J-ECB1750 Tested and working: - lan, wireless, leds, sysupgrade (tftp) Flash instructions: 1.) tftp recovery - use a 1GbE switch or direct attached 1GbE link - setup client ip address 192.168.1.10 and start tftpd - save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory - plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed - afterwards login via ssh and do a sysuprade 2.) oem webinterface factory install (not tested) Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin". 3.) oem webinterface command injection OEM Firmware already running OpenWrt (Attitude Adjustment 12.09). Use OEM webinterface and command injection. See wiki for details. https://openwrt.org/toh/engenius/engenius_ecb1750_1 Signed-off-by: sven friedmann <sf.openwrt@okay.ms> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use interrupt-driven "gpio-keys" binding]
* ath79: glinet_gl-ar750s: Use QCA9887 firmwareJeff Kletsky2019-05-051-1/+1
| | | | | | | The GL.iNet AR750S is based around the QCA9563 and requires the QCA9887 firmware for operation. Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: remove unnecessary packages from I-O DATA ETG3-RINAGAKI Hiroshi2019-04-131-0/+1
| | | | | | | | I-O DATA ETG3-R is a wired router. So wireless-related packages are unnecessary and remove those packages from default configuration to reduce flash usage. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-091-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove more duplicate image build variablesDaniel Gimpelevich2019-04-091-4/+1
| | | | | | | | | Remove Netgear-specific image build variables which are set to the same value. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [reordering of variables, removed stray newline] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-081-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for NEC Aterm WG1200CRINAGAKI Hiroshi2019-04-061-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
* ath79: add support for COMFAST CF-E5/E7Ding Tengfei2019-03-241-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on Qualcomm/Atheros QCA9531. Short specification: 2x 10/100 Mbps Ethernet, with 24v PoE support 64 MB of RAM (DDR2) 16 MB of FLASH (SPI) 2T2R 2.4 GHz, 802.11b/g/n built-in 1x 3 dBi antennas output power (max): 80 mW (19 dBm) Qucetel EC20 LTE MODULE(1x external detachable antenna) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [commit subject fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for jjPlus JA76PF2Tomasz Maciej Nowak2019-03-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board. Specification SoC: Atheros AR7161 RAM: 64 MB DDR Flash: 16 MB SPI NOR Ethernet: 2x 10/100/1000 Mbps AR8316 LAN (CN11), WAN/PoE (CN6 - close to power barrel connector, 48 V) MiniPCI: 2x LEDS: 4x, which 3 are GPIO controlled Buttons: 2x GPIO controlled Reset (SW1, closer to ethernet ports), WPS (SW2) Serial: 1x (only RX and TX are wired) baud: 115200, parity: none, flow control: none Currently there is one caveat compared to ar71xx target images as the MAC addresses are random on every reboot. To remedy this one needs to store the WAN MAC address in RedBoot configuration. OpenWrt on first boot, after flashing, will read out the address and assign proper ones to both WAN and LAN ports. It is iportant to NOT keep the old configuration when doing sysupgrade from ar71xx. Upgrading from OpenWrt ar71xx image 1. Connect to serial port, 2. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n <openwrt_sysupgrade_image_name> 3. After writing new image OpenWrt will reboot, now interrupt boot process and enter RedBoot (bootloader) command line by pressing Ctrl+C, 4. Enter following commands (replace variable accordingly), set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_adress> (confirm storing the value by inputting y and pressing Enter) reset 5. Now board should restart and boot OpenWrt with proper MAC addresses. Installation 1. Prepare TFTP server with OpenWrt initramfs image, 2. Connect to WAN ethernet port, 3. Connect to serial port, 4. Power on the board and enter RedBoot (bootloader) command line by pressing Ctrl+C, 5. Enter following commands (replace variables accordingly): set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_address> (confirm storing the value by inputting y and pressing Enter) ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress> load -r -b 0x80060000 <openwrt_initramfs_image_name> exec -c "" 6. Now board should boot OpenWrt initramfs image, 7. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade <openwrt_sysupgrade_image_name> 8. Wait few minutes, after the D2 LED will stop blinking, the board is ready for configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add suport for EnGenius EPG5000Tomasz Maciej Nowak2019-03-131-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add GL.iNet AR-300M-LiteJeff Kletsky2019-03-131-2/+12
| | | | | | | | | | | | | | | | | | | | | AR300M-Lite is single-Ethernet variant of the AR300M series Its eth0 would otherwise be assigned to the WAN interface making it unreachable firstboot or failsafe. Installation instructions from OEM (OpenWrt variant): * Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI), * Do not preserve settings * Access rebooted device via Ethernet at OpenWrt default address Add previously missing LED defaults for all three variants; -nand, -nor, -lite to the definitions in 01_leds Non-lite variants thanks to Andreas Ziegler https://patchwork.ozlabs.org/patch/1049396/ Runtime-tested: GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: add support for LibreRouter v1Santiago Piccinini2019-03-131-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve <your image>-sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 <your image>-sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
* ath79: add support for YunCore A770Piotr Dymacz2019-03-091-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE (802.3at) support, based on QCA9531 + QCA9887. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port) - 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA - 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11) - 2x regular LED, 1x RGB LED (all driven by GPIO) - 1x button (reset) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: 1. First, gain root access to the device, following below steps: - Login into web gui (default password/IP: admin/192.168.188.253). - Go to 'Advanced' -> 'Management' -> 'System' and download backup of configuration (bakfile.bin). - Open the file as tar.gz archive, edit/update 'shadow' file and change hash of root password to something known. - Repack the archive, rename it back to 'bakfile.bin' and use to restore configuration of the device. - After that, device will reboot and can be accessed over SSH. 2. Then, install OpenWrt: - Login over SSH and issue command: fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" - Upload 'sysupgrade' image and install it (only if previous command succeeded) with command: 'sysupgrade -n -F openwrt-...'. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for COMFAST CF-E120A v3Roger Pueyo Centelles2019-02-281-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless CPE with two Ethernet ports and a 802.11an radio. Specifications: - AR9344 SoC - 535/400/267 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 5 GHz, up to 25 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add ar71xx support-list entry for Fritz4020David Bauer2019-02-261-0/+1
| | | | | | | This adds the support-list entry the AVM FRITZ!Box 4020 expects in the ar71xx target to allow non-forced sysupgrades from ar71xx to ath79. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for I-O DATA WN-AC1600DGRINAGAKI Hiroshi2019-02-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - SoC: Qualcomm Atheros QCA9557 - RAM: 128 MB - Flash: 16 MB - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 5x 10/100/1000 Mbps - Switch: QCA8337N - LED/key: 6x/6x(4x buttons, 1x slide switch) - UART: through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR 2. Connect power cable to WN-AC1600DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Alternative flash instruction using initramfs image: 1. Prepare a computer and TFTP server software with the IP address "192.168.99.8" and renamed OpenWrt initramfs image "uImageWN-AC1600DGR" 2. Connect between WN-AC1600DGR and the computer with UART 3. Connect power cable to WN-AC1600DGR, press "4" on the serial console and enter the U-Boot console 4. execute "tftpboot" command on the console and download initramfs image from the TFTP server 5. execute "bootm" command and boot OpenWrt 6. On initramfs image, download the sysupgrade image to the device and perform sysupgrade with it 7. Wait ~150 seconds to complete flashing This commit also removes unnecessary "qca,no-eeprom" property from the ath10k wifi node. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-111-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Devolo WiFi Pro 1750eDjango Armstrong2019-01-261-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3) WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3) BTN: 1x Reset 1x WPS 1x USB eject LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports) Dupont 4 pin header Rear RJ45 serial port non-functional USB: 1x v2.0 Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password previously set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
* ath79: add support for devolo WiFi pro 1200iDavid Bauer2019-01-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1750iDavid Bauer2019-01-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-011-2/+2
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: rework elecom-header recipeMathias Kresin2018-12-311-26/+22
| | | | | | | | Replace the code with a more readable version. Rename the recipe to reflect the real usecase. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for COMFAST CF-E110NRoger Pueyo Centelles2018-12-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E110N, an outdoor wireless CPE with two Ethernet ports and a 802.11bgn radio. Specifications: - 650/400/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 26 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new want, so a factory reset will be needed: once the new firmware is flashed, perform the factory reset by pushing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing quicker. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Notes: The device is advertised, sold and labeled as "CF-E110N", but the bootloader and the stock firmware identify it as "v2". Acknowledgments: Petr Štetiar <ynezz@true.cz> Sebastian Kemper <sebastian_ml@gmx.net> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [drop unused labels from devicetree source file] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for EnGenius EWS511APGuan-Hong Lin2018-12-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EWS511AP is a wireless managed wall AP with PoE support, based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887. Short specification: - 128MB of RAM - 16 MB of SPI FLASH - 2T2R 2.4 GHz (QCA9531), 802.11b/g/n - 1T1R 5 GHz (QCA9887), 802.11ac/n/a - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED - 1x RESET button - built-in watchdog chipset Flash instruction: From EnGenius firmware to OpenWrt firmware: Original firmware is based on QSDK. Use sysupgrade firmware directly in vendor GUI. Reset to factory default is necessary. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the OpenWrt firmware in the root directory on your computer. 2. Power up EWS511AP. Press 4 and then press any key to enter u-boot. 3. Download OpenWrt firmware (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin" 4. Flash the firmware (ath)> erase 0x9f060000 +f50000 (ath)> cp.b $fileaddr 0x9f060000 $filesize 5. Reboot (ath)> reset Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-311-2/+2
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix boardname of GL.iNet GL-AR150Paul Wassi2018-12-311-2/+2
| | | | | | | This device is called GL-AR150, therefore rename the board to 'gl-ar150' Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for ELECOM WRC-1750GHBK2-I/CINAGAKI Hiroshi2018-12-311-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for GL.iNet GL-AR750SChristoph Krapp2018-12-311-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now this patch adds nor image generation only. NAND image generation is not supportet at the moment. Furtheremore support for the MicroSD port is not implemented as of now. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) - Another LED can be accessed on GPIO 7 if soldered Flash instruction: - Set static ip to 192.168.1.2 - Unplug the power cord - Hold reset button - Plug power back in - Right led will flash 5 times - Release reset button - Browse to 192.168.1.1 - Choose sysupgrade image in NOR-flash section - Press "update nor firmware" - After successful transfer unplug network cable before device restarts Signed-off-by: Christoph Krapp <achterin@googlemail.com> [resolve merge conflicts, rename buttons, use switch input type for mode switch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-301-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for devolo WiFi pro 1750cDavid Bauer2018-12-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button There is also a Micro-B USB-port present but this only seems to be a dummy as the circuit next to it is not present (at least in my unit). It is also not mentioned in the devolo manual. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-20 18:26:31 +0000