aboutsummaryrefslogtreecommitdiffstats
path: root/package/boot
Commit message (Collapse)AuthorAgeFilesLines
* uboot-mediatek: several fixes for MT7622Daniel Golle2021-07-114-94/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | * ! Behavior change ! Old behavior: If the Reset button is held down during power-on do factory reset and try booting recovery from TFTP forever. If valid recovery is received via TFTP, write it to flash and boot. New behavior: If the Reset button is held down during power-on do factory reset, then try TFTP *once*, then try booting on-flash recovery, then keep trying via TFTP forever until a valid image is received. Only if there is no bootable recovery stored on flash, store the downloaded recovery. Then boot it. * Set loadaddr to 0x48000000 in order to allow booting images larger than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to 0x48000000 gives us 384MB on devices with 512MB RAM, which should be more than enough as a maximum size for uImage.FIT to be loaded. * Widely unify device-specific default environment in preparation to auto-generate it from parameters. * backport upstream commit fixing MBR/DOS partitioning Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Linksys EA8100 v2Tee Hao Wei2021-07-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
* grub2: update to 2.06Dirk Neukirchen2021-06-213-59/+19
| | | | | | | | | | | | | | | -300-CVE-2015-8370.patch is upstreamed with different code (upstream id: 451d80e52d851432e109771bb8febafca7a5f1f2) - fixup OpenWrts setup_root patch compile tested: x86_64,i386 runtime tested: VM x86_64,VM i386 - booted fine - grub-editenv worked Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
* grub2: pass compilation parameters more accurately李国2021-06-201-3/+5
| | | | | | | | | In order for the grub2 boot-related code to compile normally, we have made many adjustments to the compilation parameters. These adjustments are not necessary for tools-related code. We apply these parameter adjustments only to the boot-related code. Signed-off-by: 李国 <uxgood.org@gmail.com>
* grub2: make grub2 tools built in a separate variant李国2021-06-201-2/+6
| | | | | | | | | grub2 boot-related code and tools-related code may require different compilation parameters. We split them into different variants for compilation, so that we can accurately pass the required parameters and avoid causing problems. Signed-off-by: 李国 <uxgood.org@gmail.com>
* grub2: make grub2-bios-setup as a separate package李国2021-06-201-8/+23
| | | | | | | | | | The grub2 and grub2-efi packages should only contain boot-related code. grub-bios-setup is the same as grub-editenv, they are both grub2 tools and should be placed in a separate package. Signed-off-by: 李国 <uxgood.org@gmail.com> [use AUTORELEASE and update to SPDX] Signed-off-by: Paul Spooren <mail@aparcar.org>
* uboot-rockchip: add NanoPi R4S supportTianling Shen2021-06-102-0/+301
| | | | | | Add support for the FriendlyARM NanoPi R4S. Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* uboot-kirkwood: refresh patchesAdrian Schmutzler2021-06-0610-45/+35
| | | | | | | | This is only cosmetic, but the next one adding a patch here would have to do it anyway, and thus will get a smaller diff for review now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: Add support for SheevaplugBERENYI Balazs2021-06-064-2/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: add support for Askey RT4230W REV6Lauro Moreno2021-06-051-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Askey RT4230W REV6 (Branded by Spectrum/Charter as RAC2V1K) At this time, there's no way to reinstall the stock firmware so don't install this on a router that's being rented. Specifications: Qualcomm IPQ8065 1 GB of RAM (DDR3) 512 MB Flash (NAND) 2x Wave 2 WiFi cards (QCA9984) 5x 10/100/1000 Mbps Ethernet (Switch: QCA8337) 1x LED (Controlled by a microcontroller that switches it between red and blue with different patterns) 1x USB 3.0 Type-A 12V DC Power Input UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V Port settings are 115200n8 More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830 https://deviwiki.com/wiki/Askey_RAC2V1K To check what revision your router is, restore one of these config backups through the stock firmware to get ssh access then run "cat /proc/device-tree/model". https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17 The revision number on the board doesn't seem to be very consistent so that's why this is needed. You can also run printenv in the uboot console and if machid is set to 177d, that means your router is rev6. Note: Don't install this if the router is being rented from an ISP. The defined partition layout is different from the OEM one and even if you changed the layout to match, backing up and restoring the OEM firmware breaks /overlay so nothing will save and the router will likely enter a bootloop. How to install: Method 1: Install without opening the case using SSH and tftp You'll need: RAC2V1K-SSH.zip: https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip initramfs and sysupgrade images Connect to one of the router's LAN ports Download the RAC2V1K-SSH.zip file and restore the config file that corresponds to your router's firmware (If you're firmware is newer than what's in the zip file, just restore the 1.1.16 file) After a reboot, you should be able to ssh into the router with username: "4230w" and password: "linuxbox" or "admin". Run the following commannds fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as it's in the same subnet as the server fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next steps fw_setenv bootdelay 8 fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq" Don't reboot the router yet. Install and set up a tftp server on your computer Set a static ip on the ethernet interface of your computer (use this for serverip in the above commands) Rename the initramfs image to initramfs.bin, and host it with the tftp server Reboot the router. If you set up everything right, the router led should switch over to a slow blue glow which means openwrt is booted. If for some reason the file doesn't get loaded into ram properly, it should still boot to the OEM firmware. After openwrt boots, ssh into it and run these commands: fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" fw_setenv bootdelay 2 After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Method 2: Install with serial access (Do this if something fails and you can't boot after using method 1) You'll need: initramfs and sysupgrade images Serial access: https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case Install and set up a tftp server Set a static ip on the ethernet interface of your computer Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server Connect the wan port of the router to your computer Interrupt U-Boot and run these commands: setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer) setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet) setenv bootcmd "setenv mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" saveenv tftpboot initramfs.bin bootm After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Signed-off-by: Lauro Moreno <lmore377@gmail.com> [add entry in 5.10 patch, fix whitespace issues] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Amped Wireless ALLY router and extenderJonathan Sturges2021-06-051-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Add support for OpenMesh A40Sven Eckelmann2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh A60Sven Eckelmann2021-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ramips: add support for JCG Q20Chukun Pan2021-05-261-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* kexec-tools: add patch to fix issue with appended DTB and zImage on ARMAlexander Egorenkov2021-05-232-1/+53
| | | | | | | | | | | This patch fixes a recently found problem when a zImage passed to kexec-tools contains an appended DTB. In that case kexec boot fails because the decompressor wrongly tries to use the non-existing appended DTB instaed of the one passed in the register r2. - http://lists.infradead.org/pipermail/kexec/2021-April/022353.html Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
* grub2: disable liblzma dependencyDirk Neukirchen2021-05-211-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Florian Ekert reported: "I have build a fresh master branch recently, Since your last change [1] on grub2, I have now a new dependency on liblzma for the install package grub2-editenv. root@st-dev-07 /usr/lib # ldd /root/grub-editenv /lib/ld-musl-x86_64.so.1 (0x7f684b088000) liblzma.so.5 => /usr/lib/liblzma.so.5 (0x7f684b06d000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7f684b059000) libc.so => /lib/ld-musl-x86_64.so.1 (0x7f684b088000) This was not the case before your update. root@st-dev-07 /usr/sbin # ldd /usr/sbin/grub-editenv /lib/ld-musl-x86_64.so.1 (0x7fd970176000) libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7fd970162000) libc.so => /lib/ld-musl-x86_64.so.1 (0x7fd970176000) My build complains that it cannot satisfy the runtime package dependency for grub2-editenv. install -d -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin install -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/grub-editenv /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin/ find /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv -name 'CVS' -o -name '.svn' -o -name '.#*' -o -name '*~'| xargs -r rm -rf Package grub2-editenv is missing dependencies for the following libraries: liblzma.so.5 make[2]: *** [Makefile:166: /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/bin/APOS/feckert/master/master-Maggie-455-ga5edc0e8e/x86_64/targets/x86/64/packages/grub2-editenv_2.06~rc1-1_x86_64.ipk] Error 1 make[2]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/package/boot/grub2' time: package/boot/grub2/pc/compile#78.64#9.79#83.88 ERROR: package/boot/grub2 failed to build (build variant: pc). make[1]: *** [package/Makefile:116: package/boot/grub2/compile] Error 1 make[1]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt' make: *** [/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/include/toplevel.mk:230: package/boot/grub2/compile] Error 2 If I add the following changes to the package all works as expected. <snip> - DEPENDS:=@TARGET_x86 + DEPENDS:=@TARGET_x86 +liblzma VARIANT:=pc endef This is a hotfix but I dont´t think this is the final solution, because lzma is provided by the package xz. And This is maintained in the package feed [not the core]" Dirk stated & offered his patch to disable liblzma and thus resolve the 'out of core dependency' problem: "LZMA is used in mkimage.c disabling it prints Without liblzma (no support for XZ-compressed mips images) (explicitly disabled) (see configure.ac) liblzma is autodetected so this issue was present but hidden somehow [unsure: grep/image generation does not use grub with that option] OpenWrt does not use that feature currently [!] some scripts and examples use --compression=xz or -C xz and those will break grub has an internal xzlib for different "lzma" functionality (ext. LIBLZMA from XZ (GRUB_COMPRESSION_XZ) vs. GRUB_COMPRESSION_LZMA)" Hopefully fixes e74d81ece2e2932a4f370d8e6d180061a6a2c229 and doesn't break anything else. Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name> [include Florian's description of how problem 1st encountered] [bump package release] Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* uboot-envtools: support uci-default config also per subtargetsPiotr Dymacz2021-05-201-3/+7
| | | | | | | | | | The current version of 'uboot-envtools' package generates dedicated uci-default file only per target. This change makes it possible to use subtarget-specific files, with name pattern: 'target_subtarget' (example: 'ath79_nand'). The subtarget-specific files will take precedence over target-specific one. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-imx6: update BUILD_DEVICES valuesPiotr Dymacz2021-05-201-3/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-imx6: drop 'HIDDEN' flag from 'mx6cuboxi' definePiotr Dymacz2021-05-201-1/+0
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for ZiKing CPE46BGiulio Lorenzo2021-05-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional antenna. It is low cost and mostly available via Aliexpress, references can be found at: - https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383 - https://git.lsd.cat/g/openwrt-cpe46b Specifications: - Atheros AR9330 - 32MB of RAM - 8MB of flash (SPI NOR) - 1 * 2.4ghz integrated antenna - 2 * 10/100/1000 ethernet ports (1 POE) - 3 * Green LEDs controlled by the SoC - 3 * Green LEDs controlled via GPIO - 1 * Reset Button controlled via GPIO - 1 * 4 pin serial header on the PCB - Outdoor packaging Flashing instruction: You can use sysupgrade image directly in vendor firmware which is based on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor Telnet console is vulnerable to command injection and can be used to gain a shell directly on the OEM OpenWrt distribution. Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org> [fix whitespaces, drop redundant uart status and serial0, drop num-chipselects, drop 0x1002 MAC address for wmac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* grub2: bump to 2.06-rc1Stijn Tintel2021-05-163-79/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When building GRUB with binutils 2.35.2 or later, an error occurs due to a section .note.gnu.property that is placed at an offset such that objcopy needs to pad the img file with zeros. This in turn causes the following error: "error: Decompressor is too big.". The fix accepted by upstream patches a python script that isn't executed at all when building GRUB with OpenWrt buildroot. There's another patch that patches the files generated by that python script directly, but by including it we would deviate further from upstream. Instead of doing that, simply bump to the latest release candidate. As one of the fixes for the CVEs causes grub to crash on some x86 hardware using legacy BIOS when compiled with -O2, filter -O2 and -O3 out of TARGET_CFLAGS. Fixes the following CVEs: - CVE-2020-14372 - CVE-2020-25632 - CVE-2020-25647 - CVE-2020-27749 - CVE-2020-27779 - CVE-2021-3418 - CVE-2021-20225 - CVE-2021-20233 Runtime-tested on x86/64. Fixes: FS#3790 Suggested-by: Dirk Neukirchen <plntyk.lede@plntyk.name> Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: mt7621: Add support for ZyXEL NR7101Bjørn Mork2021-05-091-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE with integrated directional 5G/LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7603E - Switch: 1 LAN port (Gigabiti) - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC - SIM: 2 micro-SIM slots under transparent cover - Buttons: Reset, WLAN under same cover - LEDs: Multicolour green/red/yellow under same cover (visible) - Power: 802.3at PoE via LAN port The device is built as an outdoor ethernet to 5G/LTE bridge or router. The Wifi interface is intended for installation and/or temporary management purposes only. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Remove the SIM/button/LED cover, the WLAN button and 12 screws holding the back plate and antenna cover together. The GPS antenna is fixed to the cover, so be careful with the cable. Remove 4 screws fixing the antenna board to the main board, again being careful with the cables. A bluetooth TTL adapter is recommended for permanent console access, to keep the router water and dustproof. The 3.3V pin is able to power such an adapter. MAC addresses: OpenWrt OEM Address Found as lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex) wwan0 usb0 random WARNING!! ISP managed firmware might at any time update itself to a version where all known workarounds have been disabled. Never boot an ISP managed firmware with a SIM in any of the slots if you intend to use the router with OpenWrt. The bootloader lock can only be disabled with root access to running firmware. The flash chip is physically inaccessible without soldering. Installation from OEM web GUI: - Log in as "supervisor" on https://172.17.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Installation from OEM ssh: - Log in as "root" on 172.17.1.1 port 22022 - scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp - Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit - Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Copying OpenWrt to the recovery partition: - Verify that you are running a working OpenWrt recovery image from flash - ssh to root@192.168.1.1 and run: fw_setenv CheckBypass 0 mtd -r erase Kernel2 - Wait while the bootloader mirrors Image1 to Image2 NOTE: This should only be done after successfully booting the OpenWrt recovery image from the primary partition during installation. Do not do this after having sysupgraded OpenWrt! Reinstalling the recovery image on normal upgrades is not required or recommended. Installation from Z-Loader: - Halt boot by pressing Escape on console - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - Sysupgrade to the OpenWrt sysupgrade image NOTE: ATNR will write the recovery image to both primary and recovery partitions in one go. Booting from RAM: - Halt boot by pressing Escape on console - Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu - Press "4" to select "4: Entr boot command line interface." - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Load it using "tftpboot 0x88000000 initramfs-recovery.bin" - Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL header This method can also be used to RAM boot OEM firmware. The warning regarding OEM applies! Never boot an unknown OEM firmware, or any OEM firmware with a SIM in any slot. NOTE: U-Boot configuration is incomplete (on some devices?). You may have to configure a working mac address before running tftp using "setenv eth0addr <mac>" Unlocking the bootloader: If you are unebale to halt boot, then the bootloader is locked. The OEM firmware locks the bootloader on every boot by setting DebugFlag to 0. Setting it to 1 is therefore only temporary when OEM firmware is installed. - Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware - Run "fw_setenv DebugFlag 0x1" in OpenWrt NOTE: OpenWrt does this automatically on first boot if necessary NOTE2: Setting the flag to 0x1 avoids the reset to 0 in known OEM versions, but this might change. WARNING: Writing anything to flash while the bootloader is locked is considered extremely risky. Errors might cause a permanent brick! Enabling management access from LAN: Temporary workaround to allow installing OpenWrt if OEM firmware has disabled LAN management: - Connect to console - Log in as "root" - Run "iptables -I INPUT -i br0 -j ACCEPT" Notes on the OEM/bootloader dual partition scheme The dual partition scheme on this device uses Image2 as a recovery image only. The device will always boot from Image1, but the bootloader might copy Image2 to Image1 under specific conditions. This scheme prevents repurposing of the space occupied by Image2 in any useful way. Validation of primary and recovery images is controlled by the variables CheckBypass, Image1Stable, and Image1Try. The bootloader sets CheckBypass to 0 and reboots if Image1 fails validation. If CheckBypass is 0 and Image1 is invalid then Image2 is copied to Image1. If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to Image2. If CheckBypass is 1 then all tests are skipped and Image1 is booted unconditionally. CheckBypass is set to 1 after each successful validation of Image1. Image1Try is incremented if Image1Stable is 0, and Image2 is copied to Image1 if Image1Try is 3 or larger. But the bootloader only tests Image1Try if CheckBypass is 0, which is impossible unless the booted image sets it to 0 before failing. The system is therefore not resilient against runtime errors like failure to mount the rootfs, unless the kernel image sets CheckBypass to 0 before failing. This is not yet implemented in OpenWrt. Setting Image1Stable to 1 prevents the bootloader from updating Image1Try on every boot, saving unnecessary writes to the environment partition. Keeping an OpenWrt initramfs recovery as Image2 is recommended primarily to avoid unwanted OEM firmware boots on failure. Ref the warning above. It enables console-less recovery in case of some failures to boot from Image1. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* uboot-mediaktek: add support for PSTORE and check it on bootDaniel Golle2021-05-085-15/+131
| | | | | | | | Add support for pstore/ramoops now that DRAM content is preserved over reboot on MT7622. On each boot, check pstore and boot to recovery image in case there are records stored in it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: update to git HEADDaniel Golle2021-05-081-3/+3
| | | | | | | Most notably this enabled use of pstore/ramoops on MT7622 as DRAM content is now preserved over reboot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: change size for unifi-6-lrDaniel Golle2021-05-071-1/+1
| | | | | | | The previous commit increased the U-Boot environment size of the UniFi 6 LR to 0x4000. Also change it uboot-envtools accordingly. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: unifi-6-lr: fix erase of production paritionDaniel Golle2021-05-072-13/+15
| | | | | | | | | | | mtd erase needs to be aligned with erase blocks. Use padded image size for erasing the production volume. As the environment grew above the current size of 0x1000 bytes by introducing the new padding function, increase the env size to 0x4000. While at it, clean up reset button function to work to more reliable on that board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-mediatek: bpi-r64: add TFTP update options to eMMC bootmenuDaniel Golle2021-05-011-6/+14
| | | | | | | Just like on SPI-NAND, also allow updating the bootloader comfortably on eMMC installations. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add support for Buffalo WZR-HP-G300NHMauri Sandberg2021-04-301-0/+4
| | | | | | This adds an entries for wzr-hp-g300nh-rb and wzr-hp-g300nh-s. Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
* uboot-mediatek: unifi6lr: mtd erase before write to flashChen Minqiang2021-04-281-2/+2
| | | | | | | | Erase firmware ereas before writing to recovery or production partition when updating them via the bootloader menu. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: fix boot hang on unifi-6-lrDaniel Golle2021-04-281-3/+3
| | | | | | | | | | | | The Ubiquiti Networks UniFi 6 LR access point comes with a total of 512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to problems with the DDR calibration on boot resulting in occasional hang on boot. Use updated calibration binary provided by MediaTek to make boot on that device more reliable. The binary has also been tested on the BananaPi BPi-R64 board and that also works just fine with the new binary. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-rockchip: update to v2021.04David Bauer2021-04-205-671/+31
| | | | | | | | | Update the uboot-rockchip to the latest upstream release. Remove upstreamed patches. Tested-on: FriendlyElec NanoPi R2S Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-envtools: mvebu: add Buffalo LS421DEDaniel González Cabanelas2021-04-171-0/+3
| | | | | | | | The Buffalo Linkstation LS421DE NAS lacks an uboot env config file. Create it via scripts. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* uboot-sunxi: update ATF dependencies for 3 boardsZoltan HERPAI2021-04-151-3/+3
| | | | | | | Fix 3 board definitions that were missed in the process of moving to the a64/h6 ATF blobs. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: add support for Banana Pi M2 BerryZoltan HERPAI2021-04-121-0/+7
| | | | | | | | | | | | | | | | | | CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz Memory: 1GB DDR3 Storage: SDcard, native SATA Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT USB: 4x USB 2.0 Installation: Use the standard sunxi installation to an SD-card. While the board is very similar to the M2 Ultra board (the V40 is the automotive version of the R40), as both the u-boot and kernel supports them separately, and some pins are different, let's add a separate device spec. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-mediatek: minor fixes for bpi-r64 spi-nand default envDaniel Golle2021-04-111-5/+4
| | | | | | | * check image checksums before writing to flash * only bootmenu_0...9 are working, remove bootmenu_a entry Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: add support for H6 boards and OrangePiOnePlusZoltan HERPAI2021-04-113-0/+23
| | | | | | | | | | | | | | | | | | | | Specifications: SoC Allwinner H6 @ 1.8 Ghz DRAM 1Gb LPDDR3 Power DC 5V @ 3A Video HDMI (Type 2.0A - full) Audio HDMI, on-board microphone Network 10/100/1000Mbps Ethernet (Realtek RTL8211) Storage microSD USB 1 USB2.0 Host, 1 USB2.0 OTG Debug Serial UART Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* arm-trusted-firmware-sunxi: move to use the common tf-a build code and bump ↵Zoltan HERPAI2021-04-112-14/+20
| | | | | | | | | | | | | | | | | | | | | | | | to latest version Create a -a64 package for now. Moving to the latest ATF was tested on a SoPine A64 board. U-Boot SPL 2020.04 (Feb 19 2021 - 11:28:19 +0000) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.4(release):reboot-15854-g42b39a13d2 NOTICE: BL31: Built : 22:45:53, Feb 22 2021 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x4090a28, model: SoPine with baseboard NOTICE: PSCI: System suspend is unavailable U-Boot 2020.04 (Feb 19 2021 - 11:28:19 +0000) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: SoPine with baseboard DRAM: 2 GiB Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-sunxi: add ATF variable for specifying which flavour to useZoltan HERPAI2021-04-112-2/+11
| | | | | | | In preparation for H6 support (which requires a separate ATF blob), add an envvar to the A64 boards specifying which ATF blob to use. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* uboot-envtools: support environment in spi-nand on bpi-r64Daniel Golle2021-04-111-3/+11
| | | | | | | Default to U-Boot env in UBI if root device is not mmc block device. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* uboot-mediatek: add spi-nand build for bananapi bpi-r64Daniel Golle2021-04-113-21/+302
| | | | | | | | Some of bpi-r64 boards have serial NAND attached to SPI bus. Build U-Boot for booting from SPI-NAND. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: fix writing bananapi bpi-r64 envOskari Lemmela2021-04-111-3/+4
| | | | | | | Use generic functions to get env partition. Fixes: 7043e4334f0 ("mediatek: mt7622: improve sysupgrade on MMC") Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mediatek: bpi-r64: use separate partition for emmc bootloaderOskari Lemmela2021-04-111-4/+4
| | | | | | | eMMC booloader is stored to separate partition. FIP size is increased to 2MB. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* uboot-envtools: oxnas: drop redundant space after case keywordsPiotr Dymacz2021-04-101-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: layerscape: drop redundant space after case keywordsPiotr Dymacz2021-04-101-1/+1
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: ipq806x: drop redundant space after case keywordsPiotr Dymacz2021-04-101-3/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: ipq40xx: drop redundant space after case keywordsPiotr Dymacz2021-04-101-10/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: imx6: drop redundant space after case keywordsPiotr Dymacz2021-04-101-28/+28
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* uboot-envtools: drop shebang from uci-defaults and lib filesPiotr Dymacz2021-04-1016-18/+0
| | | | | | These files are sourced and non-executable, a shebang is redundant. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>