aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/realtek
Commit message (Collapse)AuthorAgeFilesLines
* treewide: call check-size before append-metadataAdrian Schmutzler2021-07-101-1/+1
| | | | | | | | | | sysupgrade metadata is not flashed to the device, so check-size should be called _before_ adding metadata to the image. While at it, do some obvious wrapping improvements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* realtek: Fix failsafe modeHauke Mehrtens2021-06-222-0/+19
| | | | | | | | | | | | | | | The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is configured. Do not use the standard failsafe configuration for DSA accessing the default port directly, but configure a switch on the lan1 interface instead. This will add the VLAN ID 1 configuration to the switch: $ bridge vlan show port vlan-id lan1 1 PVID Egress Untagged switch 1 PVID Egress Untagged Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: Fix buffer length calculation on RTL8380 with CRC offloadBirger Koblitz2021-06-221-9/+7
| | | | | | | | | | | | | Fixes the buffer and packet length calculations for Ethernet TX on the RTL8380 SoC when CRC calculation offload is enabled. CRC-offload is always done by the SoC, but additional CRC calculation was previously done also by the kernel. It also fixes detection of the DSA tag for packets on RTL8390 SoCs for ports > 28. v2 has correct whitespace Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
* base-files: generate network config with "device" optionsRafał Miłecki2021-05-271-1/+1
| | | | | | | Replace "ifname" with "device" as netifd has been recently patches to used the later one. It's more clear and accurate. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* realtek: Fix VLAN issues introduced by multicast patchesBirger Koblitz2021-05-093-5/+5
| | | | | | | | | | This adds the CPU port to the unknown multicast flooding port mask, which fixes the VLAN issues introduced by the multicast group patches Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3] Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix] Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
* realtek: Add support for Layer 2 MulticastBirger Koblitz2021-05-075-300/+1024
| | | | | | | | | | Adds support for Layer 2 multicast by implementing the DSA port_mdb_* callbacks. The Kernel bridge listens to IGMP/MLD messages trapped to the CPU-port, and calls the Multicast Forwarding Database updates. The updates manage the L2 forwarding entries and the multicast port-maps. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Setup all VLANs with default configurationsBirger Koblitz2021-05-075-0/+75
| | | | | | | | This sets up all VLANs with a default configuration on reset: - forward based on VLAN-ID and not the FID/MSTI - forward based on the inner VLAN-ID (not outer) Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add SoC-specific VLAN setup routineBirger Koblitz2021-05-074-114/+259
| | | | | | | | This adds SoC specific VLAN configuration routines, which alsoe sets up the portmask table entries that are referred to in the vlan profiles registers for unknown multicast flooding. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add support for clause45 PHYsBirger Koblitz2021-05-076-234/+563
| | | | | | | | This adds support for the MMD access registers the RTL-SoCs use to access clause 45 PHYs via mdio. This new interface is used to add EEE-support for the RTL8226 Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: improve EEE support for RTL8380/8390/9300Birger Koblitz2021-05-075-33/+301
| | | | | | | Clean up and fix bugs in the EEE support for RTL8380/90 Adds EEE support for RTL9300 Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Add L2 hash bucket sizeBirger Koblitz2021-05-072-3/+5
| | | | | | | | Adds a hash-bucket size attribute for the different SoCs, in order to accomodate the buckets with 8 entries of the L2-forwarding tables on RTL93XX in contrast to only 4 on RTL83XX. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: remove unused FDB print routingBirger Koblitz2021-05-071-21/+0
| | | | | | remove fdb_dump debugging function Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add IGMP/MLD snooping supportBirger Koblitz2021-05-072-4/+7
| | | | | | | This adds snooping support for IGMP and MLD on RTL8380/90/9300 by trapping IGMP and MLD packets to the CPU. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: enable CRC offloadingBirger Koblitz2021-05-071-24/+93
| | | | | | | | | | Enables CRC calculation offloading on RTL8380/8390/9300. Tested on Zyxel XGS1210-10 (RTL9302)/GS1900-48 (RTL8390)/GS1900-10HP (RTL8382) On the Zyxel GS1900-10HP, an increase of 5% in iperf3 send throughput and 11% in receive throughput is seen. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add support for INABA Abaniact AML2-17GPINAGAKI Hiroshi2021-05-072-0/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | INABA Abaniact AML2-17GP is a 17 port gigabit switch, based on RTL8382. Specification: - SoC : Realtek RTL8382 - RAM : DDR3 128 MiB (SK hynix H5TQ1G63EFR) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FZ2I-10G) - Ethernet : 10/100/1000 Mbps x17 - port 1-8 : RTL8218B (SoC) - port 8-16 : RTL8218D - port wan : RTL8214FC - LEDs/Keys : 1x, 1x - UART : pin header on PCB (Molex 530470410 compatible) - J14: 3.3V, GND, RX, TX from rear side - 115200n8 - Power : 100-240 VAC, 50/60 Hz, 0.21 A - Plug : IEC 60320-C13 Flash instruction using initramfs image: 1. Boot AML2-17GP normally 2. Set the IP address of computer to the range of 192.168.1.0/24, other than 192.168.1.248 and connect computer to "WAN/CONSOLE" port of AML2-17GP 3. Access to "http://192.168.1.248" and open firmware setting page -- UI Language: 日本語 -- "メンテナンス" -> "デュアルイメージ" -- UI Language: ENGLISH -- "Maintenance" -> "Dual Image" 4. Check "イメージ情報 (en: "Images Information")" and set the first image to active by choosing "アクティブイメージ" (en: "Active Image") in the partition "0" 5. open firmware upgrade page -- UI Language: 日本語 -- "メンテナンス" -> "アップグレードマネージャー" -- UI Language: ENGLISH -- "Maintenance" -> "Upgrade Manager" 6. Set the properties as follows -- UI Language: 日本語 -- "アップグレード方式" : "HTTP" "アップグレードタイプ" : "イメージ" "イメージ" : "アクティブ" "ブラウズファイル" : (select the OpenWrt initramfs image) -- UI Language: ENGLISH -- "Upgrade Method" : "HTTP" "Upgrade Type" : "Image" "Image" : "(Active)" "Browse file" : (select the OpenWrt initramfs image) 7. Press "アップグレード" (en: "Upgrade") button and perform upgrade 8. Wait ~150 seconds to complete flashing 9. After the flashing, the following message is showed and press "OK" button to reboot -- UI Language: 日本語 -- "成功!! 今すぐリブートしますか?" -- UI Language: ENGLISH -- "Success!! Do you want to reboot now?" 10. After the rebooting, reconnect the cable to other port (1-16) and open the SSH connection, download the sysupgrade image to the device and perform sysupgrade with it 11. Wait ~120 seconds to complete sysupgrade Note: - The uploaded image via WebUI will only be written with the length embedded in the uImage header. If the sysupgrade image is specified, only the kernel is flashed and lacks the rootfs, this causes a kernel panic while booting and bootloops. To avoid this issue, initramfs image is required for flashing on WebUI of stock firmware. - This device has 1x LED named as "POWER", but it's not connected to the GPIO of SoC and cannot be controlled. - port 17 is named as "WAN/CONSOLE". This port is for the upstream connection and console access (telnet/WebUI) on stock firmware. Back to stock firmware: 1. Set "bootpartition" variable in u-boot-env2 partition to "1" by fw_setsys fw_setsys bootpartition 1 2. Reboot AML2-17GP Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: Add support for Netgear S350 series switches GS308T and GS310TPRaylynn Knight2021-05-079-60/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear GS308T v1 is an 8 port gigabit switch. The GS310TP v1 is an 8 port POE+ gigabit switch with 2 SFP Ports (currently untested). The GS308T v1 and GS310TP v1 are quite similar to the Netgear GS1xx devices already supported. Theses two devices use the same Netgear firmware and are very similar to there corresponding GS1xx devices. For this reason they share a large portion of the device tree with the GS108T and GS110TP with exception of the uimage magic and model and compatible values. All of the above feature a dual firmware layout, referred to as Image0 and Image1 in the Netgear firmware. In order to manipulate the PoE+ on the GS310TP v1 , one needs the rtl83xx-poe package Specifications (GS308T) ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12) * 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ) * RTL8231 GPIO extender to control the LEDs and the reset button * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B) * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1 * Power is supplied via a 12V 1A barrel connector Specifications (GS310TP) ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * Nuvoton M0516LDN for controlling PoE * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12) * 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ) * RTL8231 GPIO extender to control the LEDs and the reset button * 8 x 10/100/1000BASE-T PoE+ ports, 2 x Gigabit SFP ports, internal PHY (RTL8218B) * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1 * Power is supplied via a 54V 1.25A barrel connector Both devices have UART pinout ----------- J1 | [o]ooo ^ ||`------ GND | |`------- RX [TX out of the serial adapter] | `-------- TX [RX into the serial adapter] `---------- Vcc (3V3) [the square pin] The through holes are filled with PB-free solder which melts at 375C. They can also be drilled using a 0.9mm bit. Installation ------------ Instructions are identical to those for the similar Negear devices and apply both to the GS308T v1 and GS310TP v1 as well. ------------------- Boot initramfs image from U-Boot -------------------------------- 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Init network with `rtk network on` command 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs308t-v1-initramfs-kernel.bin` command 4. Boot the image with `bootm` command The switch defaults to IP 192.168.1.1 and tries to fetch the image via TFTP from 192.168.1.111. Updating the installed firmware ------------------------------- The OpenWRT ramdisk image can be flashed directly from the Netgear UI. The Image0 slot should be used in order to enable sysupgrade. As with similar switches, changing the active boot partition can be accomplished in U-Boot as follows: 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Run `setsys bootpartition {0|1}` to select the boot partition 3. Run `savesys` followed by `boota` to proceed with the boot process Signed-off-by: Raylynn Knight <rayknight@me.com>
* kernel: bump 5.4 to 5.4.116John Audia2021-05-071-1/+1
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-211-2/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* realtek: allow writing to "u-boot-env2"Bjørn Mork2021-04-085-5/+0
| | | | | | | | U-Boot uses the "bootpartition" variable stored in "u-boot-env2" to select the active system partition. Allow updates to enable system switching from OpenWrt. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: rename partitions in Netgear DTSIStijn Segers2021-04-031-5/+5
| | | | | | | | | Switch the Netgear DTSI for the Realtek target from the OEM partition naming scheme to accepted OpenWrt naming practices. A quick git grep for 'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* realtek: add ZYXEL_VERS to DEVICE_VARSAdrian Schmutzler2021-03-221-0/+2
| | | | | | | | Otherwise, the last defined value will be set for all devices. Fixes: c6c8d597e183 ("realtek: Add generic zyxel_gs1900 image definition") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: enable SerDes NWAY and SGMII negotiationBjørn Mork2021-03-172-3/+42
| | | | | | | This allows copper SFPs to negotiate speeds lower than 1gig. Acked-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: enabled Marvell and Realtek PHYsBjørn Mork2021-03-171-0/+2
| | | | | | | | | | The rtl83xx-phy driver is necessary for proper configuration of the PHYs if U-Boot hasn't done that. 1000Base-T SFPs often contains a Marvell 88E1111 and will not work without this driver. Include it by default to support copper SFPs. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: enable HWMON for SFP sensorsBjørn Mork2021-03-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds SFP sensors as a hwmon device, allowing readout of temperatures, DOM and other sensor readings available from the SFP. Example from a ZyXEL GS1900-10HP with a DOM capable 1000Base-SX SFP: root@gs1900-10hp:~# grep . /sys/class/hwmon/hwmon0/* /sys/class/hwmon/hwmon0/curr1_crit:90 /sys/class/hwmon/hwmon0/curr1_crit_alarm:0 /sys/class/hwmon/hwmon0/curr1_input:4 /sys/class/hwmon/hwmon0/curr1_label:bias /sys/class/hwmon/hwmon0/curr1_lcrit:0 /sys/class/hwmon/hwmon0/curr1_lcrit_alarm:0 /sys/class/hwmon/hwmon0/curr1_max:85 /sys/class/hwmon/hwmon0/curr1_max_alarm:0 /sys/class/hwmon/hwmon0/curr1_min:0 /sys/class/hwmon/hwmon0/curr1_min_alarm:0 /sys/class/hwmon/hwmon0/in0_crit:3795 /sys/class/hwmon/hwmon0/in0_crit_alarm:0 /sys/class/hwmon/hwmon0/in0_input:3317 /sys/class/hwmon/hwmon0/in0_label:VCC /sys/class/hwmon/hwmon0/in0_lcrit:2805 /sys/class/hwmon/hwmon0/in0_lcrit_alarm:0 /sys/class/hwmon/hwmon0/in0_max:3465 /sys/class/hwmon/hwmon0/in0_max_alarm:0 /sys/class/hwmon/hwmon0/in0_min:3135 /sys/class/hwmon/hwmon0/in0_min_alarm:0 /sys/class/hwmon/hwmon0/name:sfp_p10 /sys/class/hwmon/hwmon0/power1_crit:708 /sys/class/hwmon/hwmon0/power1_crit_alarm:0 /sys/class/hwmon/hwmon0/power1_input:259 /sys/class/hwmon/hwmon0/power1_label:TX_power /sys/class/hwmon/hwmon0/power1_lcrit:89 /sys/class/hwmon/hwmon0/power1_lcrit_alarm:0 /sys/class/hwmon/hwmon0/power1_max:501 /sys/class/hwmon/hwmon0/power1_max_alarm:0 /sys/class/hwmon/hwmon0/power1_min:126 /sys/class/hwmon/hwmon0/power1_min_alarm:0 /sys/class/hwmon/hwmon0/power2_crit:1259 /sys/class/hwmon/hwmon0/power2_crit_alarm:0 /sys/class/hwmon/hwmon0/power2_input:404 /sys/class/hwmon/hwmon0/power2_label:RX_power /sys/class/hwmon/hwmon0/power2_lcrit:6 /sys/class/hwmon/hwmon0/power2_lcrit_alarm:0 /sys/class/hwmon/hwmon0/power2_max:794 /sys/class/hwmon/hwmon0/power2_max_alarm:0 /sys/class/hwmon/hwmon0/power2_min:10 /sys/class/hwmon/hwmon0/power2_min_alarm:0 /sys/class/hwmon/hwmon0/temp1_crit:100000 /sys/class/hwmon/hwmon0/temp1_crit_alarm:0 /sys/class/hwmon/hwmon0/temp1_input:22547 /sys/class/hwmon/hwmon0/temp1_label:temperature /sys/class/hwmon/hwmon0/temp1_lcrit:-50000 /sys/class/hwmon/hwmon0/temp1_lcrit_alarm:0 /sys/class/hwmon/hwmon0/temp1_max:85000 /sys/class/hwmon/hwmon0/temp1_max_alarm:0 /sys/class/hwmon/hwmon0/temp1_min:-40000 /sys/class/hwmon/hwmon0/temp1_min_alarm:0 /sys/class/hwmon/hwmon0/uevent:OF_NAME=sfp-p10 /sys/class/hwmon/hwmon0/uevent:OF_FULLNAME=/sfp-p10 /sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_0=sff,sfp /sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_N=1 Tested-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: re-enable sfp driver for ZyXEL GS1900-10HPBjørn Mork2021-03-171-18/+6
| | | | | | | | | | | | | There is no need to define a static link or a phy for the sfp ports. Using phy-mode and managed properties to describe the link to the sfp phy. We have to keep the now unconnected virtual "phys" because the switch driver uses their "phy-is-integrated" property to figure out which ports to enable as fibre ports. Acked-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: need to handle PHY_INTERFACE_MODE_NA for sfpsBjørn Mork2021-03-171-0/+1
| | | | | | | | | | From the validate docs in include/linux/phylink.h: When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the MAC driver to return all supported link modes. Tested-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: fix link-state interruptBjørn Mork2021-03-171-4/+3
| | | | | | | This bug was the root cause for the failing sfp driver. Acked-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: Add ZyXEL GS1900-8Hauke Mehrtens2021-03-142-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or SFP ports, but otherwise similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-8 v1.2 * SoC: Realtek RTL8380M 500 MHz MIPS 4KEc * Flash: Macronix MX25L12835F 16 MiB * RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM * Ethernet: 8x 10/100/1000 Mbit * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 8 ethernet port status LEDs (green, SoC controlled) * Buttons: 1 on-off glide switch at the back (not configurable) 1 reset button at the right side, behind the air-vent (not configurable) 1 reset button on front panel (configurable) * Power 12V 1A barrel connector * UART: 1 serial header (JP2) with populated standard pin connector on the left side of the PCB, towards the back. Pins are labelled: + VCC (3.3V) + TX (really RX) + RX (really TX) + GND the labelling is done from the usb2serial connector's point of view, so RX/ TX are mixed up. Serial connection parameters for both devices: 115200 8N1. Installation ------------ Instructions are identical to those for the GS1900-10HP and GS1900-8HP. * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-10HP is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot off the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: Add generic zyxel_gs1900 image definitionHauke Mehrtens2021-03-141-13/+13
| | | | | | | Add a new common device definition for the Zyxel GS1900 line of switches. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: drop ethtool log noiseBjørn Mork2021-03-122-15/+15
| | | | | | | | | | | | | Demote a number of debugging printk's to pr_debug to avoid log nosie. Several of these functions are called as a result of userspace activity. This can cause a lot of log noise when userspace does periodic polling. Most of this could probably be removed completely, but let's keep it for now since these drivers are still in development. Signed-off-by: Bjørn Mork <bjorn@mork.no> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-062-2/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel-5.4: bump to 5.4.102 and refresh patchesJason A. Donenfeld2021-03-041-2/+2
| | | | | | | | | | | | | | 5.4.102 backported a lot of stuff that our WireGuard backport already did, in addition to other patches we had, so those patches were removed from that part of the series. In the process other patches were refreshed or reworked to account for upstream changes. This commit involved `update_kernel.sh -v -u 5.4`. Cc: John Audia <graysky@archlinux.us> Cc: David Bauer <mail@david-bauer.net> Cc: Petr Štetiar <ynezz@true.cz> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* realtek: add support for Netgear GS108T v3Michael Mohr2021-02-122-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support on port 1. The two prior versions were built using eCos and are not currently compatible with OpenWRT. The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3, all of which use the same firmware image from Netgear. For this reason, the device tree is identical aside from the model and compatible values. All of the above feature a dual firmware layout, referred to as Image0 and Image1 in the Netgear firmware. Hardware specification ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12) * 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ) * RTL8231 GPIO extender to control the LEDs and the reset button * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B) * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1 * Power is supplied via a 12V 1A barrel connector or 802.3af UART pinout ----------- J1 | [o]ooo ^ ||`------ GND | |`------- RX [TX out of the serial adapter] | `-------- TX [RX into the serial adapter] `---------- Vcc (3V3) [the square pin] The through holes are filled with PB-free solder which melts at 375C. They can also be drilled using a 0.9mm bit. Build configuration ------------------- * Target System: Realtek MIPS * Target Profile: Netgear GS108T v3 * Target Images -> ramdisk -> Compression: lzma * Disable other target images Boot initramfs image from U-Boot -------------------------------- 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Init network with `rtk network on` command 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command 4. Boot the image with `bootm` command The switch defaults to IP 192.168.1.1 and tries to fetch the image via TFTP from 192.168.1.111. Updating the installed firmware ------------------------------- The OpenWRT ramdisk image can be flashed directly from the Netgear UI. The Image0 slot should be used in order to enable sysupgrade. As with similar switches, changing the active boot partition can be accomplished in U-Boot as follows: 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Run `setsys bootpartition {0|1}` to select the boot partition 3. Run `savesys` followed by `boota` to proceed with the boot process Signed-off-by: Michael Mohr <akihana@gmail.com>
* realtek: refactor the Netgear GS110TPP v1 device treeMichael Mohr2021-02-122-225/+139
| | | | | | | | | | | | | | | | | | | Move most of the GS110TPP v1 device tree into a dtsi so that it can be shared with the GS108T v3. Additionally: * Use macros to simplify the ethernet and switch definitions * Zero-pad the offsets and sizes in the partition map to 8 digits each The spi-max-frequency value has been changed from 10MHz to 50MHz based on an analysis of the relevant datasheets. The current driver doesn't use this property, as the clock speed is fixed. However, it's required for this type of DT node, so that's why it's present here. The firmware partition has been split in half, since this is how the stock firmware uses it. This can be used to easily revert to a stock firmware if one is written to the second image area. Signed-off-by: Michael Mohr <akihana@gmail.com>
* realtek: add and use netgear_nge for the GS110PP v1Michael Mohr2021-02-121-6/+12
| | | | | | | | The netgear_nge device will be shared between the GS108T v3 (to be added in a later commit) and the GS110PP v1. It also enables LZMA compression for the ramdisk image. Signed-off-by: Michael Mohr <akihana@gmail.com>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-103-9/+5
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.93John Audia2021-01-292-4/+4
| | | | | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64 Run-tested [*]: ath79/generic, ipq40xx, octeon, ramips/mt7621 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* realtek: add debugfs support for mirroringBirger Koblitz2021-01-261-14/+391
| | | | | | This adds debugfs support to monitor mirroring via debugfs Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add API for the hw tables of RTL83XX/93XX SoCsBirger Koblitz2021-01-261-100/+436
| | | | | | | | Add a table API that has per accss register locking and uses register description information to handle all table access through a single set of api calls. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add switch driver support for the RTL93XX based switchesBirger Koblitz2021-01-265-245/+1522
| | | | | | | Adds support for the RTL9300 and RTL9310 series of switches with 10GBit per port and up to 56 ports. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add internal and external SDS/PHYs of RTL9300 devicesBirger Koblitz2021-01-262-28/+523
| | | | | | | | This adds support for the internal SerDes of the RTL9300 SoC and for the RTL8218D and RTL8226B phys found in combination with this SoC in switches. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: fix RTL8231 gpio expander usage with RTL839X SoCBirger Koblitz2021-01-261-24/+40
| | | | | | | | This fixes the usage of the RTL8231 GPIO extender chip when used with the RTL839X SoCs. Specifically, the PHY addresses may be different from 0. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: enable default rate limiting and qos settingsBirger Koblitz2021-01-261-64/+0
| | | | | | | Enable default rate limiting and QoS support. Remove previous storm control code. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: correct l2 offloading tag handlingBirger Koblitz2021-01-261-4/+7
| | | | | | | Makes sure the DSA trailer information on any L2 offloading done by the switch is honoured by the bridge layer Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add QoS and rate controlBirger Koblitz2021-01-266-530/+1955
| | | | | | | | | This adds support for identifying QoS information in packets and use this and rate control information to submit to multiple egress queues. The ethernet driver is also made to support 2 egress and up to 32 egress queues. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add dtsi for RTL930X SoCsBirger Koblitz2021-01-261-0/+182
| | | | | | Add a default dtsi to support RTL930X SoCs. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add support for the RTL9300 timerBirger Koblitz2021-01-264-22/+349
| | | | | | | | this adds support for the SoC timer of the RTL9300 chips, it provides 6 independent timer/counters, of which the first one is used as a clocksource and the second one as event timer. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add support for the RTL8390 and RTL9300 SoC IRQsBirger Koblitz2021-01-264-150/+174
| | | | | | | | This adds support for the RTL8390 and RTL9300 SoCs it also cleans up unnecessary definitions in mach-rtl83xx.h and moves definitions relevant for irq routing to irq.h Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: add detection of RTL930X SoCs and RTL8313 SoCBirger Koblitz2021-01-261-6/+65
| | | | | | | | This adds support to detect RTL930X based SoCs and the RTL9313 SoC. Tested on Zyxel XGS1210-10 (RTL9302B SoC) and the Zyxel XS1930-12 (RTL9313 SoC) Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: build ZyXEL vendor firmware compatible initramfsBjørn Mork2021-01-241-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Append a device specific version trailer used by the stock firmware upgrade application to validate firmwares. The trailer contains a list of ZyXEL firmware version numbers, which includes a four letter hardware identifier. The stock web UI requires that the current hardware matches one of the listed versions, and that the version number is larger than a model specific minimum value. The minimum version varies between V1.00 and V2.60 for the currently known GS1900 models. The number is not used anywhere else to our knowlege, and has no direct relation to the version info in the u-image header. We can therefore use an arbitrary value larger than V2.60. The stock firmware upgrade application will only load and flash the part of the file specified in the u-image header, regardless of file size. It can therefore not be used to flash images with an appended rootfs. There is therefore no need to include the trailer in other images than the initramfs. This prevents accidentally bricking by attempts to flash other images from the stock web UI. Stock images support all models in the series, listing all of them in the version trailer. OpenWrt provide model specific images. We therefore only list the single supported hardware identifier for each image. This eliminates the risk of flashing the wrong OpenWrt image from stock web UI. OpenWrt can be installed from stock firmware in two steps: 1) flash OpenWrt initramfs image from stock web gui 2) boot OpenWrt and sysupgrade to a squasfs image The OpenWrt squashfs image depends on a static partition map in the DTS. It can only be installed to the "firmware" partition. This partition is labeled "RUNTIME1" in u-boot and in stock firmware, and is referred to as "image 0" in the stock flash management tool. The OpenWrt initramfs can be installed and run from either partitions. But if you want to keep stock irmware in the spare system partition, then you must make sure stock firmware is installed to the "RUNTIME2" partition referred to as "image 1" in the stock web UI. And the initial OpenWrt initramfs must be flashed to "RUNTIME1"/"image 0". The stock flash management application supports direct selection of both which partition to flash and which partition to boot next. This allows software controlled "dual-boot" between OpenWrt and stock firmware, without using console access to u-boot. u-boot use the "bootpartition" variable stored in the second u-boot environment to select which of the two system partitions to boot. This variable is set by the stock flash management application, by direct user input. It can also be set in OpenWrt using e.g fw_setsys bootpartition 1 to select "RUNTIME2"/"image 1" as default, assuming a stock firmware version is installed in that partition. Signed-off-by: Bjørn Mork <bjorn@mork.no>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-10 17:51:46 +0000