aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/image/generic.mk
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-091-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove more duplicate image build variablesDaniel Gimpelevich2019-04-091-4/+1
| | | | | | | | | Remove Netgear-specific image build variables which are set to the same value. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [reordering of variables, removed stray newline] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-081-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for NEC Aterm WG1200CRINAGAKI Hiroshi2019-04-061-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
* ath79: add support for COMFAST CF-E5/E7Ding Tengfei2019-03-241-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on Qualcomm/Atheros QCA9531. Short specification: 2x 10/100 Mbps Ethernet, with 24v PoE support 64 MB of RAM (DDR2) 16 MB of FLASH (SPI) 2T2R 2.4 GHz, 802.11b/g/n built-in 1x 3 dBi antennas output power (max): 80 mW (19 dBm) Qucetel EC20 LTE MODULE(1x external detachable antenna) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [commit subject fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for jjPlus JA76PF2Tomasz Maciej Nowak2019-03-181-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board. Specification SoC: Atheros AR7161 RAM: 64 MB DDR Flash: 16 MB SPI NOR Ethernet: 2x 10/100/1000 Mbps AR8316 LAN (CN11), WAN/PoE (CN6 - close to power barrel connector, 48 V) MiniPCI: 2x LEDS: 4x, which 3 are GPIO controlled Buttons: 2x GPIO controlled Reset (SW1, closer to ethernet ports), WPS (SW2) Serial: 1x (only RX and TX are wired) baud: 115200, parity: none, flow control: none Currently there is one caveat compared to ar71xx target images as the MAC addresses are random on every reboot. To remedy this one needs to store the WAN MAC address in RedBoot configuration. OpenWrt on first boot, after flashing, will read out the address and assign proper ones to both WAN and LAN ports. It is iportant to NOT keep the old configuration when doing sysupgrade from ar71xx. Upgrading from OpenWrt ar71xx image 1. Connect to serial port, 2. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n <openwrt_sysupgrade_image_name> 3. After writing new image OpenWrt will reboot, now interrupt boot process and enter RedBoot (bootloader) command line by pressing Ctrl+C, 4. Enter following commands (replace variable accordingly), set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_adress> (confirm storing the value by inputting y and pressing Enter) reset 5. Now board should restart and boot OpenWrt with proper MAC addresses. Installation 1. Prepare TFTP server with OpenWrt initramfs image, 2. Connect to WAN ethernet port, 3. Connect to serial port, 4. Power on the board and enter RedBoot (bootloader) command line by pressing Ctrl+C, 5. Enter following commands (replace variables accordingly): set_mac (to view MAC addresses) alias ethaddr <wan_port_mac_address> (confirm storing the value by inputting y and pressing Enter) ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress> load -r -b 0x80060000 <openwrt_initramfs_image_name> exec -c "" 6. Now board should boot OpenWrt initramfs image, 7. Download OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade <openwrt_sysupgrade_image_name> 8. Wait few minutes, after the D2 LED will stop blinking, the board is ready for configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add suport for EnGenius EPG5000Tomasz Maciej Nowak2019-03-131-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add GL.iNet AR-300M-LiteJeff Kletsky2019-03-131-2/+12
| | | | | | | | | | | | | | | | | | | | | AR300M-Lite is single-Ethernet variant of the AR300M series Its eth0 would otherwise be assigned to the WAN interface making it unreachable firstboot or failsafe. Installation instructions from OEM (OpenWrt variant): * Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI), * Do not preserve settings * Access rebooted device via Ethernet at OpenWrt default address Add previously missing LED defaults for all three variants; -nand, -nor, -lite to the definitions in 01_leds Non-lite variants thanks to Andreas Ziegler https://patchwork.ozlabs.org/patch/1049396/ Runtime-tested: GL.iNet AR300M-Lite Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: add support for LibreRouter v1Santiago Piccinini2019-03-131-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve <your image>-sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 <your image>-sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
* ath79: add support for YunCore A770Piotr Dymacz2019-03-091-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE (802.3at) support, based on QCA9531 + QCA9887. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port) - 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA - 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11) - 2x regular LED, 1x RGB LED (all driven by GPIO) - 1x button (reset) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: 1. First, gain root access to the device, following below steps: - Login into web gui (default password/IP: admin/192.168.188.253). - Go to 'Advanced' -> 'Management' -> 'System' and download backup of configuration (bakfile.bin). - Open the file as tar.gz archive, edit/update 'shadow' file and change hash of root password to something known. - Repack the archive, rename it back to 'bakfile.bin' and use to restore configuration of the device. - After that, device will reboot and can be accessed over SSH. 2. Then, install OpenWrt: - Login over SSH and issue command: fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" - Upload 'sysupgrade' image and install it (only if previous command succeeded) with command: 'sysupgrade -n -F openwrt-...'. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ath79: add support for COMFAST CF-E120A v3Roger Pueyo Centelles2019-02-281-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless CPE with two Ethernet ports and a 802.11an radio. Specifications: - AR9344 SoC - 535/400/267 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 5 GHz, up to 25 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: add ar71xx support-list entry for Fritz4020David Bauer2019-02-261-0/+1
| | | | | | | This adds the support-list entry the AVM FRITZ!Box 4020 expects in the ar71xx target to allow non-forced sysupgrades from ar71xx to ath79. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for I-O DATA WN-AC1600DGRINAGAKI Hiroshi2019-02-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - SoC: Qualcomm Atheros QCA9557 - RAM: 128 MB - Flash: 16 MB - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 5x 10/100/1000 Mbps - Switch: QCA8337N - LED/key: 6x/6x(4x buttons, 1x slide switch) - UART: through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR 2. Connect power cable to WN-AC1600DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Alternative flash instruction using initramfs image: 1. Prepare a computer and TFTP server software with the IP address "192.168.99.8" and renamed OpenWrt initramfs image "uImageWN-AC1600DGR" 2. Connect between WN-AC1600DGR and the computer with UART 3. Connect power cable to WN-AC1600DGR, press "4" on the serial console and enter the U-Boot console 4. execute "tftpboot" command on the console and download initramfs image from the TFTP server 5. execute "bootm" command and boot OpenWrt 6. On initramfs image, download the sysupgrade image to the device and perform sysupgrade with it 7. Wait ~150 seconds to complete flashing This commit also removes unnecessary "qca,no-eeprom" property from the ath10k wifi node. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-111-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Devolo WiFi Pro 1750eDjango Armstrong2019-01-261-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3) WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3) BTN: 1x Reset 1x WPS 1x USB eject LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports) Dupont 4 pin header Rear RJ45 serial port non-functional USB: 1x v2.0 Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password previously set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
* ath79: add support for devolo WiFi pro 1200iDavid Bauer2019-01-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1750iDavid Bauer2019-01-051-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-011-2/+2
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: rework elecom-header recipeMathias Kresin2018-12-311-26/+22
| | | | | | | | Replace the code with a more readable version. Rename the recipe to reflect the real usecase. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for COMFAST CF-E110NRoger Pueyo Centelles2018-12-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E110N, an outdoor wireless CPE with two Ethernet ports and a 802.11bgn radio. Specifications: - 650/400/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 26 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new want, so a factory reset will be needed: once the new firmware is flashed, perform the factory reset by pushing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing quicker. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Notes: The device is advertised, sold and labeled as "CF-E110N", but the bootloader and the stock firmware identify it as "v2". Acknowledgments: Petr Štetiar <ynezz@true.cz> Sebastian Kemper <sebastian_ml@gmx.net> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [drop unused labels from devicetree source file] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for EnGenius EWS511APGuan-Hong Lin2018-12-311-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EWS511AP is a wireless managed wall AP with PoE support, based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887. Short specification: - 128MB of RAM - 16 MB of SPI FLASH - 2T2R 2.4 GHz (QCA9531), 802.11b/g/n - 1T1R 5 GHz (QCA9887), 802.11ac/n/a - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED - 1x RESET button - built-in watchdog chipset Flash instruction: From EnGenius firmware to OpenWrt firmware: Original firmware is based on QSDK. Use sysupgrade firmware directly in vendor GUI. Reset to factory default is necessary. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the OpenWrt firmware in the root directory on your computer. 2. Power up EWS511AP. Press 4 and then press any key to enter u-boot. 3. Download OpenWrt firmware (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin" 4. Flash the firmware (ath)> erase 0x9f060000 +f50000 (ath)> cp.b $fileaddr 0x9f060000 $filesize 5. Reboot (ath)> reset Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-311-2/+2
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix boardname of GL.iNet GL-AR150Paul Wassi2018-12-311-2/+2
| | | | | | | This device is called GL-AR150, therefore rename the board to 'gl-ar150' Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for ELECOM WRC-1750GHBK2-I/CINAGAKI Hiroshi2018-12-311-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for GL.iNet GL-AR750SChristoph Krapp2018-12-311-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now this patch adds nor image generation only. NAND image generation is not supportet at the moment. Furtheremore support for the MicroSD port is not implemented as of now. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) - Another LED can be accessed on GPIO 7 if soldered Flash instruction: - Set static ip to 192.168.1.2 - Unplug the power cord - Hold reset button - Plug power back in - Right led will flash 5 times - Release reset button - Browse to 192.168.1.1 - Choose sysupgrade image in NOR-flash section - Press "update nor firmware" - After successful transfer unplug network cable before device restarts Signed-off-by: Christoph Krapp <achterin@googlemail.com> [resolve merge conflicts, rename buttons, use switch input type for mode switch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-301-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for devolo WiFi pro 1750cDavid Bauer2018-12-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button There is also a Micro-B USB-port present but this only seems to be a dummy as the circuit next to it is not present (at least in my unit). It is also not mentioned in the devolo manual. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for devolo WiFi pro 1200eDavid Bauer2018-12-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for NEC Aterm WG800HPINAGAKI Hiroshi2018-12-241-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 1T1R (QCA9887) - 4x 10/100/1000 Mbps Ethernet - 8x LEDs, 3x keys (2x buttons, 1x slide-switch) - UART through-hole on PCB (J2) - Vcc, GND, NC, TX, RX from SoC side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WG800HP 2. Connect power cable to WG800HP and turn on it 3. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: replace cameo-factory with existing build commandsMathias Kresin2018-12-171-2/+4
| | | | | | | | Use pad-offset and append-string to create the cameo factory images for the D-LINK DIR-825 C1/DIR-835 A1 factory images. Tested-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx/ath79: switch devices to the -ct driver and firmwareChristian Lamparter2018-12-171-1/+1
| | | | | | | Since commit 61b5b4971e7 ("mac80211: make ath10k-ct the default ath10k") select ath10k-ct and the -ct firmwares by default. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add d-link dir-825-c1 and dir-835-a1Sebastian Kemper2018-12-171-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79. They're pretty much identical, except dir-835-a1 has less LEDs. The routers come with 128 MByte of RAM and 16 MBytes of flash and sport 2.4GHz and 5.0GHz wireless. Both routers have entries already in OpenWrt's TOH. Please check there for more information on these antiquities. https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1 https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1 Installation: 1. Connect to the web interface of the vendor firmware (usually listening on 192.168.0.1). 2. Go to "Tools", then "Firmware". 3. In the "Firmware Upgrade" box click "Browse". 4. Select the OpenWrt factory image for your router. 5. Click "Upload", confirm the popups if you agree to flash the file you selected. 6. Wait for firmware upgrade to complete. It takes about 5 minutes. Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't have this router so I can't confirm. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
* ath79: add support for I-O DATA WN-AG300DGRINAGAKI Hiroshi2018-12-061-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Winchannel WB2000Chuanhong Guo2018-12-061-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WB2000 is a dual-band 11N AP using AR9344. The factory firmware used the original DB120 partition table with a small kernel partition at the end of firmware and the kernel will easily get oversized in the future. Since it has to be flashed using UART I also swapped kernel/rootfs and changed the default load address. Specification: - SoC: Atheros AR9344 - RAM: 128 MB - Flash: 16 MB - Ethernet: 10/100/1000 Mbps (Atheros AR8035) - 2x USB 2.0 - WIFI: AR9344(2G) + AR9382(5G) - RTC: DS1338 Known issue: 5G ath9k led doesn't work due to commit ccab68f. Flash instruction: Set up a TFTP server on your computer and configure static IP. Connect UART (J11 TX/GND/RX) and press any key to enter U-boot shell. 1. Change the default boot command: setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000' saveenv 2. Set your router ipaddr and server ipaddr. e.g.: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.50 3. Load and flash the firmware: tftp 0x80060000 fw.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 4. Reset your router: reset Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [Drop the i2c node unit address. Move the ath9k-leds node out of the spi node, it doesn't belong there. Add the #gpio-cells property to the pci wifi node. All fix dtc compiler warnings] Signed-off-by: Mathias Kresin <dev@kresin.me> merge
* ath79: remove duplicate image build variablesMathias Kresin2018-12-061-10/+2
| | | | | | | Remove image build variables which are set to the same value as the default image build recipe. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix GL.iNet GL-AR300M sysupgradeMathias Kresin2018-12-061-2/+2
| | | | | | | | | | | The userspace boardname derived from the dts compatible was out of sync with the expected board added to the image metadata. This way a sysupgrade is refused. Sync the userspace boardname and the baordname used in the image metdata to allow a seamless sasupgrade. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: rename qca9533.dtsi to qca953x.dtsiChuanhong Guo2018-12-061-2/+2
| | | | | | | | | qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE. Rename the misleading dtsi names and fix the SoC type of gl-ar300m. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [apply the changes for the gl-x750 as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for ROSINSON WR818 boardRosy Song2018-11-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the ROSINSON WR818 WiFi-Router SoC: Qualcomm Atheros QCA9563, FLASH: Winbond W25Q128FV 16MBytes, WiFi: QCA9563 b/g/n 3x3 450Mbit/s, USB: 1x USB 2.0 Type A, 1x USB2.0 Type C, IN: WPS/Reset button GPIO1, OUT: Power LED red, Internet LED red, WLAN LED red, LAN1 LED red, LAN2 LED red, System LED red, UART: RX-GPIO18, TX-GPIO22, Tested and working: - Ethernet (LAN + WAN) - WiFi - OpenWRT sysupgrade - Button - LEDs Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.1.1 - Go to "Administration" -> "Firmware Upgrade" - Upload the OpenWrt sysupgrade image Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: rename glinet x750Mathias Kresin2018-11-271-3/+3
| | | | | | The boardname is gl-x750 and is already used for the led names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: modify mtd partitions for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-11-261-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and move it to generic subtarget. In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs" partition in the stock firmware. This causes the size of the kernel to be limited by the fixed value. 0x50000 0xe80000 0xff0000 +-------------------------------+--------------+ | rootfs | kernel | | (14528k) | (1472k) | +-------------------------------+--------------+ After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2 exceeded the limit, and it breaks builds on official buildbot. Since this issue was also confirmed in ath79, I modified the mtd partitions to get rid of that limitation. 0x50000 0xff0000 +----------------------------------------------+ | firmware | | (16000k) | +----------------------------------------------+ However, this commit breaks compatibility with ar71xx firmware, so I dropped "SUPPORTED_DEVICES += bhr-4grv2". This commit requires new flash instruction instead of the old one. Flash instruction using initramfs image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Set the IP address of the computer to 192.168.12.10 3. Rename the OpenWrt initramfs image to "bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP directory 4. Start the tftp server on the computer 5. While holding down the "ECO" button, connect power cable to BHR-4GRV2 and turn on it 6. Flashing (orange) diag LED and release the finger from the button, BHR-4GRV2 downloads the intiramfs image from TFTP server and boot with it 7. On the initramfs image, create "/etc/fw_env.config" file with following contents /dev/mtd1 0x0 0x10000 0x10000 8. Execute following commands to add environment variables for u-boot fw_setenv ipaddr 192.168.12.1 fw_setenv serverip 192.168.12.10 fw_setenv ethaddr 00:aa:bb:cc:dd:ee fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" 9. Perform sysupgrade with squashfs-sysupgrade image 10. Wait ~150 seconds to complete flashing And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC, not QCA9558. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for GL-iNet GL-X750Luo chongjun2018-11-261-0/+8
| | | | | | | | | | | | | | | | | | | this patch adds supports for GL-X750. Specification: - SOC: QCA9531 (650MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 10/100: 1xLAN + 10/100: 1xWAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x reset button - LED: 5x LEDS (green) Flash instruction: The original firmware is openwrt, so both LuCI or sysupgrade can be used. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
* ath79: add support for Buffalo WZR-HP-G302H A1A0INAGAKI Hiroshi2018-10-071-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros AR7242. It is Japanese market model of WZR-HP-G300NH2, but there are some diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx. And, G302H has several hardware versions and hardware is different dependent on the versions. This commit adds support for "A1A0" version. Specification: - Atheros AR7242 - 64 MB of RAM (DDR2) - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 2.4 GHz 2T2R wifi - Atheros AR9283 - 5x 10/100/1000 Mbps Ethernet - Atheros AR8316 - 7x LEDs, 5x keys - LED: 1x gpio-leds, 6x ath9k-leds - key: 3x buttons, 2x slide switches - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/" and move to firmware update page ("ファーム更新") 3. Select the OpenWrt factory image and click update ("更新実行") button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add hwver parameter to buffalo-tagINAGAKI Hiroshi2018-10-071-3/+3
| | | | | | | In order to be able to set the value of "hardware version" other than "3", I added the "hwver" parameter. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Buffalo BHR-4GRVINAGAKI Hiroshi2018-09-261-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV is a wired router, based on Atheros AR7242. Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 2x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the BHR-4GRV normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware upgrade 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix support for Buffalo WZR-HP-G450H and split to dts/dtsiINAGAKI Hiroshi2018-09-261-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are many parts that are incorrect or missing in the current code for Buffalo WZR-HP-G450H in ath79, so its support is broken. I fixed that issues and split to dts/dtsi files to add support for Buffalo BHR-4GRV. And WZR-450HP has the same hardware as WZR-HP-G450H, so I change the device name to "WZR-HP-G450H/WZR-450HP". Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 3T3R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 5x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the WZR-HP-G450H (or WZR-450HP) normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-261-5/+5
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* ath79: add support for Buffalo WZR-HP-AG300HBernhard Frauendienst2018-09-101-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-AG300H is a dual band router based on Qualcom Atheros AR7161 rev 2 Specification: - 680 MHz CPU (Qualcomm Atheros AR7161) - 128 MiB RAM (2x Samsung K4H511638G-LCCC) - 32 MiB Flash (2x Winbond 25Q128BVFG) - WiFi 5 GHz a/n (Atheros AR9220) - WiFi 2.4 GHz b/g/n (Atheros AR9223) - 1000Base-T WAN (Atheros AR7161) - 4x 1000Base-T Switch (Atheros AR8316) - 1x USB 2.0 - 3 Buttons (AOSS/WPS, Reset, USB Eject) - 2 Slide switches (Router (on/off/auto), Movie Engine (on/off)) - 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber, WLAN 5GHz green, WLAN 5GHz LED amber, Router green, Diag red, Movie Engine blue, USB green) It is already supported by the ar71xx target. For more information on the device visit the wiki: <https://openwrt.org/toh/buffalo/wzr-hp-ag300h> Serial console: - The UART Header is next to Movie Engine Switch. - Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V) - The Serial setting is 115200-8-N-1. Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.11.1 - Go to “Administration” → “Firmware Upgrade” - Upload the OpenWrt factory image Tested: - Ethernet (LAN, WAN) - WiFi - Installation - via TFTP rescue - via factory image - on firmware v1.77 (28-05-2012) - on pro firmware v24SP2 r30356 (26-03-2018) - via sysupgrade from ar71xx (wlan devices don't work because of new names) - via sysupgrade from itself - Buttons - LEDS - USB (Power control and device recognition) Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
* ath79: add support for ELECOM WRC-300GHBK2-IINAGAKI Hiroshi2018-09-101-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 4x keys(connected to GPIO: 3x) - UART header on PCB - TX, GND, RX, Vcc from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot the WRC-300GHBK2-I normaly and connect the computer to its LAN port 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with squashfs-sysupgrade image for WRC-300GHBK2-I 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for WD My Net Wi-Fi Range ExtenderChristian Lamparter2018-09-101-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports over support for the device from ar71xx. SOC: AR7370 (Wasp - AR9344 rev2 0001974c) RAM: Winbond W9725G6KB-25 32MiB FLASH: Winbond 25Q64FVSIG 8MiB WLAN: AR9380 Dual-Band 802.11abgn 3x3:3 INPUT: WPS, RESET button (hardware on/off toggle button) LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high) Serial: Header Next to the winbond flash chip (labeld JP1) Pinout is GND - NC - RX - TX - 3V3 (JP1) The Serial setting is 115200-8-N-1. - Installation via uboot's upgrade command 0. attach serial cable 1. interrupt uboot and enter "upgrade code.bin" into the u-boot prompt ar7240> upgrade code.bin 2. rename openwrt...sysupgrade.bin to code.bin on PC 3. run a tftp-client on the PC (shell)$ tftp 192.168.1.230 binary put code.bin 4. wait for the device to finish [...] Copy buff to Flash from 0x9f040000 length 0x79f000 Copy to Flash... write addr: 9f040000 done 5. enter "go" in the u-boot prompt ar7240> go - TFTP ramdisk image boot from the uboot prompt (tftp server defaults to serverip 192.168.1.254) => tftpboot 81000000 initramfs.bin => bootm Tested and working: - LEDs - Buttons - Ethernet - Wi-Fi - OpenWRT sysupgrade For flashing and debricking information see: <https://openwrt.org/toh/wd/rext> Users coming from ar71xx can use sysupgrade too. But I highly advise to no save the old configuration and start from a clean state. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for I-O DATA ETG3-RINAGAKI Hiroshi2018-08-231-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA ETG3-R is a wired router, based on Atheros AR9342. Specification: - Atheros AR9342 - 64 MB of RAM - 8 MB of Flash - 5x 10/100/1000 Ethernet - AR8327N - 2x LEDs, 1x key - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using initramfs image: 1. Connect serial cable to UART header on ETG3-R 2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in the TFTP directory 3. Set IP address of the computer to 192.168.0.10, connect to the LAN port of ETG3-R, and start the TFTP server on the computer 4. Connect power cable to ETG3-R and turn on the router 5. Press "Enter" key when the "Hit any key to stop autoboot:" message is displayed on the console and enter the u-boot cli 6. execute following commands to change kernel address for u-boot setenv bootsf 1 setenv mtd_kernel1 "bootm 0x9f050000" saveenv 7. execute "tftpboot; bootm" command to download the initramfs image from TFTP server and boot with it 8. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for ETG3-R 9. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 14:18:57 +0000