aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* ipq806x: use consistent DT labels for gsbiX_serialAdrian Schmutzler2020-07-142-4/+4
| | | | | | | | | | Kernel uses the label gsbiX_serial, so let's adjust our labels to this naming scheme. This is cosmetic, and actually only already existing gsbi4_serial has been used at all. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149Adrian Schmutzler2020-07-142-11/+1
| | | | | | | | | | | | | | | | | | | | | | | This device uses a node incorrectly named "alias" instead of "aliases" since it was introduced. Remove it without replacement, as the definitions in it don't seem to be required anyway: The serial0 definition has never been effective anyway and this would be the only device deviating from the common setting "serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong node prevented us from finding out about the wrong serial definition?) The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48f6 anyway, the redundant definition in the alias node was just overlooked back then. Fixes: 0fd202f3e563 ("ipq806x: add db149 dts files") Fixes: d2a2eb7e48f6 ("ipq806x: replace caf nss-gmac driver by upstream stmmac") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* procd: allow optional watchdog instance parameterDaniel Bailey2020-07-141-2/+2
| | | | | | | | | | | | | | Optional instance watchdog timeout and watchdog mode can be set by adding: procd_set_param $mode $timeout $mode is an integer [0-1] representing instance watchdog mode of operation: 0 = disabled 1 = passive mode, client must periodically poke watchdog via ubus $timeout is an integer representing how often, in seconds, the watchdog must be poked. Signed-off-by: Daniel Bailey <danielb@meshplusplus.com>
* procd: update to git HEADDaniel Golle2020-07-141-3/+3
| | | | | | | 639df57 uxc: fix build with uClibc-ng b2230e4 procd: add service instance watchdog Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: use rgmii-id instead of rgmii in ubnt,lap-120Roger Pueyo Centelles2020-07-131-3/+2
| | | | | | | | | | | Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init) the incoming incoming traffic on the ubnt,lap-120 devices Ethernet port was not making it through. Using rgmii-id instead of rgmii (same configuration as ubnt,litebeam-ac-gen2) fixes it. Fixes FS#2893. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* build,json: fix compatibility with Python 3.5Paul Spooren2020-07-131-1/+1
| | | | | | | | The f-string feature was introduced in Python 3.6. As Buildbots may run on Debian 9, which comes per default with Python 3.5, this would cause an issue. Instead of f-strings use the *legacy* `.format()` function. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ramips: add support for D-Link DIR-878 A1Mathieu Martin-Borret2020-07-133-1/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB NOR SPI flash WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) LAN: 5x1000M Firmware layout is Uboot with extra 96 bytes in header Base PCB is AP-MTKH7-0002 LEDs Power Green,Power Orange,Internet Green,Internet Orange LEDs "2.4G" Green & "5G" Green connected directly to wifi module Buttons Reset,WPS,WIFI Flashing instructions: Upload image via emergency recovery mode Push and hold reset button (on the back of the device) until power led starts flashing (about 10 secs or so) while powering the device on. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Some browsers/OS combinations are known not to work, so if you don't see the percentage complete displayed and moving within a few seconds, restart the procedure from scratch and try anoher one, or try the command line way. Alternative method using command line on Linux: curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1 Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com> [use of generic uimage-padhdr in image generation code] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: mtdsplit_uimage: add SGE parserMathieu Martin-Borret2020-07-131-0/+38
| | | | | | | Adding SGE parser for SGE (T&W) Shenzhen Gongjin Electronics to add 96 bytes padding the the firmware image Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
* glibc: fix avx2 strncmp offset compare condition check [BZ #25933]Hans Dedecker2020-07-131-2/+2
| | | | | | | 4e8a33a959 NEWS: Mention BZ 25933 fix fd15ba932d Fix avx2 strncmp offset compare condition check [BZ #25933 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* rockchip: don't disable timer LED triggerDavid Bauer2020-07-131-1/+0
| | | | | | | | The timer LED trigger is enabled in all targets (except for lantiq xway-legacy). It's necessary for the OpenWrt preinit LED pattern to work. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: use downstream GPIO button implementationDavid Bauer2020-07-132-2/+1
| | | | | | | | Use the OpenWrt netlink GPIO button implementation to forward button presses to procd. This is necessary to make failsafe-mode access using a button possible. Signed-off-by: David Bauer <mail@david-bauer.net>
* procd: update to git HEADDaniel Golle2020-07-131-3/+3
| | | | | | | | | | | | | | aed7fb3 procd: fix compilation with uClibc-ng 9d0f831 jail: fix segfault with len(uidmap/gidmap) > 1 42a6217 jail: consider PATH for argv in OCI container 83f4b72 jail: actually chdir into OCI defined CWD fc9f614 jail: parse and run OCI hooks 02eec92 jail: memory allocation fixes 71e75f4 jail: refactor mount support to cover OCI spec b586e7d jail: don't make mount source read-only dacab12 uxc: fix 'stop' command Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm47xx: disable image for Linksys WRT160n v3Adrian Schmutzler2020-07-131-0/+1
| | | | | | | | | | | | The device can only hold 3.6 MB, but newer images (since 18.06) are bigger, so flashing a new version fails. This disables default build for this device based on the bug report referenced below. Fixes: FS#1963 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate Netgear devices for mt7628Adrian Schmutzler2020-07-137-283/+151
| | | | | | | | | | | | | | | This creates a common DTSI and shared image definition for the relatively similar Netgear devices for mt7628 platform. As a side effect, this raises SPI flash frequency for the R6120, as it's expected to work there as well if it works for R6080 and R6020. Based on the data from the other devices, it also seems probable the 5g MAC address for R6120 could be extracted from the caldata, and the mtd-mac-address there could be dropped. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* wireguard: bump to 1.0.20200712Jason A. Donenfeld2020-07-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This release brings parity with the commits Linus released a few hours ago into 5.8-rc5. * receive: account for napi_gro_receive never returning GRO_DROP The napi_gro_receive function no longer returns GRO_DROP ever, making handling GRO_DROP dead code. This commit removes that dead code. Further, it's not even clear that device drivers have any business in taking action after passing off received packets; that's arguably out of their hands. * device: implement header_ops->parse_protocol for AF_PACKET WireGuard uses skb->protocol to determine packet type, and bails out if it's not set or set to something it's not expecting. For AF_PACKET injection, we need to support its call chain of: packet_sendmsg -> packet_snd -> packet_parse_headers -> dev_parse_header_protocol -> parse_protocol Without a valid parse_protocol, this returns zero, and wireguard then rejects the skb. So, this wires up the ip_tunnel handler for layer 3 packets for that case. * queueing: make use of ip_tunnel_parse_protocol Now that wg_examine_packet_protocol has been added for general consumption as ip_tunnel_parse_protocol, it's possible to remove wg_examine_packet_protocol and simply use the new ip_tunnel_parse_protocol function directly. * compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops These are required for moving wg_examine_packet_protocol out of wireguard and into upstream. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* scripts/env: Fix 56f813674a scripts/env: use command -v instead of whichKevin Darbyshire-Bryant2020-07-121-1/+1
| | | | | | | | | | We don't need to see how git will be executed and it produces non silent output on 'scripts/env diff' commands when there are no differences unlike before. Re-introduce original silent behaviour. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: fix dsa binding for TP-Link TL-WR941ND v2Chuanhong Guo2020-07-122-13/+9
| | | | | | | | | upstream changed dt-bindings for marvell 88e6060 to use mdio-device and dropped support for legacy bindings. fix it in our local dts. Fixes: FS#2524 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qihoo,c301: use phy-supply for usb vbusChuanhong Guo2020-07-121-2/+2
| | | | | | | | Linux phy subsystem provides support for a phy regulator defined via phy-supply property. Use it to turn on usb power only when usb is probed. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mvebu: add support for MACCHIATObin Single ShotTomasz Maciej Nowak2020-07-124-7/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based Marvell ARMADA 8040 Community board. Single Shot was broken as the device tree is different on the Double Shot Board. Specifications: - Quad core Cortex-A72 (up to 2GHz) - DDR4 DIMM slot with optional ECC and single/dual chip select support - Dual 10GbE (1/2.5/10GbE) SFP+ 2.5GbE (1/2.5GbE) via SFP 1GbE via copper - SPI Flash - 3 X SATA 3.0 connectors - MicroSD connector - eMMC - PCI x4 3.0 slot - USB 2.0 Headers (Internal) - USB 3.0 connector - Console port (UART) over microUSB connector - 20-pin Connector for CPU JTAG debugger - 2 X UART Headers - 12V input via DC Jack - ATX type power connector - Form Factor: Mini-ITX (170 mm x 170 mm) More details at http://macchiatobin.net Installation: Write the Image to your Micro SD Card and insert it in the MACCHIATObin Single Shot SD Card Slot. In the U-Boot Environment: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually (hanging lines indicate wrapped one-line command): setenv fdt_name armada-8040-mcbin-singleshot.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv On newer Bootloaders (18.12) the Variables have been changed, use: setenv fdt_name armada-8040-mcbin-singleshot.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr_r - $fdt_addr_r' Reported-by: Alexandra Alth <alexandra@alth.de> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: Alexandra Alth <alexandra@alth.de> [add specs and installation as provided by Alexandra Alth] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* scripts/mkits.sh: fix use of printfAdrian Schmutzler2020-07-111-2/+3
| | | | | | | | | | | Due to a line break, printf was accidentally called with three arguments instead of two, causing a different output than before. Fix it by splitting the printf command into two lines. Fixes: 907053193a1c ("scripts/mkits.sh: replace echo -e with printf") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate recipes with uimage_padhdrAdrian Schmutzler2020-07-113-13/+8
| | | | | | | | | | | There are already two very similar recipes using uimage_padhdr in ramips target, and a third one is about to be added. Make the recipe more generic, so redefinitions are not necessary anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
* mvebu: fix support for Marvell 8040 MACCHIATOBinAdrian Schmutzler2020-07-115-6/+20
| | | | | | | | | | | | | | | | | | | | | | Between kernels 4.20 and 5.0, a new variant of this board has been introduced ("Single Shot"), and the existing one has been renamed with the appendix "Double Shot". [1] This also adjusted the first compatible in the list: marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot This patch updates the OpenWrt implementation of this device by adjusting the relevant references to that compatible (i.e., our board name). To still provide support for 4.19 with our setup, this adds a small patch to change the compatible there as well. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52 Cc: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* bcm63xx: R5010UNv2: fix flash partitions for 16MB flashDaniel González Cabanelas2020-07-111-5/+5
| | | | | | | | | | | The router Nucom R5010UN v2 has the partitions defined for a 8MB flash, but the flash chip is 16MB size. We are wasting half of the flash. Fix it and use generic names for partitions. Fixes: 474cde61234c ("brcm63xx: probe SPI flash through DT") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* build: improve ccache supportRoman Yeryomin2020-07-119-10/+29
| | | | | | | | | | | | | | | | | | Set CCACHE_DIR to $(TOPDIR)/.ccache and CCACHE_BASEDIR to $(TOPDIR). This allows to do clean and dirclean. Cache hit rate for test build after dirclean is ~65%. If CCACHE is enabled stats are printed out at the end of building process. CCACHE_DIR config variable allows to override default, which could be useful when sharing cache with many builds. cacheclean make target allows to clean the cache. Changes from v1: - remove ccache directory using CCACHE_DIR variable - remove ccache leftovers from sdk and toolchain make files - introduce CONFIG_CCACHE_DIR variable - introduce cacheclean make target Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: mt7621: refactor set affinity scriptDENG Qingfang2020-07-111-19/+7
| | | | | | | | The current one only looks for mt76x2e and mt7603e, and does not work for 2 or more same Wi-Fi chips. Refactor the script to cover those cases. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ltq-vmmc: update permission handlingSebastian Kemper2020-07-112-13/+7
| | | | | | | | | | | | | | The firmware is currently just copied. It can end up with o= on the device (this is the case for voice_ar9_firmware.bin for instance). Instead of copying it the Makefile is changed to use the macro "$(INSTALL_DATA)" in order for the file to be world-readable. While at it refactor the device node creation in the init script with loop. Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> [removed 2nd part with custom group handling for device nodes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* layerscape: define IMAGE_SIZE and LS_SYSUPGRADE_IMAGE_SIZEYangbo Lu2020-07-113-10/+18
| | | | | | | | | Define 64m IMAGE_SIZE for flash firmware.bin since the flash size is 64MB. Define 48m LS_SYSUPGRADE_IMAGE_SIZE for flash sysupgrade.bin which contains maximum 16MB kernel and 32MB rootfs according to memory map. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support sysupgrade for SD card ext4 rootfsYangbo Lu2020-07-114-6/+141
| | | | | | Support sysupgrade for SD card ext4 rootfs. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support sysupgrade for squashfs rootfsYangbo Lu2020-07-119-13/+35
| | | | | | | Support sysupgrade for all Layerscape boards with squashfs rootfs. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: fix board name for SD card bootYangbo Lu2020-07-111-0/+13
| | | | | | | | | Many Layerscape boards support both flash boot and SD card boot. And different firmware and sysupgrade.bin are built for the two boot methods. To identify them, a fix could be done on board name by adding a postfix "-sdboot" for SD card boot. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add compatible for board ls1043ardbYangbo Lu2020-07-111-0/+28
| | | | | | Backport a dts patch which added compatible for ls1043ardb. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: convert to squashfs rootfs for QSPI NOR bootYangbo Lu2020-07-114-20/+8
| | | | | | | | | | | There had been an issue in Layerscape QSPI driver for very long time, which made squashfs,jffs2 rootfs not work on QSPI NOR. And the ubifs had been used as a workaround. Now the issue has been fixed. So convert to use squashfs,jffs2 rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/ LS1088ARDB), and update u-boot bootargs for booting. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* busybox: store applet usage messages uncompressedRui Salvaterra2020-07-111-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The rootfs squashfs is already highly (XZ) compressed. Storing the applet messages in compressed form will increase the entropy and reduce the overall image compression ratio. Size diffs (compressed vs uncompressed): busybox (the executable): 364596 vs 384804 bytes. OpenWrt target images (the kernel image is unchanged, obviously): omnia-medkit-openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs.tar.gz: 9163597 vs 9162531 bytes (1066 bytes difference). openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin: 9161688 vs 9160600 bytes (1088 bytes difference). openwrt-mvebu-cortexa9-cznic_turris-omnia-sysupgrade.img.gz: 9729550 vs 9729230 bytes (320 bytes difference). All in all, we save just a little bit over 1 kiB. As an added bonus, we also don't have to decompress the messages twice, (first from squashfs, then from the bzip2 message storage). Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [added additional size comparision diff detaisl] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* base-files/functions.sh: use command -v instead of whichRosen Penev2020-07-111-2/+2
| | | | | | | | which must be executed. command -v is a shell builtin. https://github.com/koalaman/shellcheck/wiki/SC2230 Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/mkits.sh: fix remaining shellcheck warningPetr Štetiar2020-07-111-1/+1
| | | | | | | | | | Fixes following shellcheck warning: In scripts/mkits.sh line 19: "-k kernel [-D name -d dtb] -o its_file" "$(basename $0)" ^-- SC2086: Double quote to prevent globbing and word splitting. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* scripts/mkits.sh: switch from bash to shRosen Penev2020-07-111-1/+1
| | | | | | This no longer needs bash. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/mkits.sh: fix improper string and array concatenationRosen Penev2020-07-111-1/+1
| | | | | | Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/mkits.sh: add missing quotesRosen Penev2020-07-111-2/+2
| | | | | | Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/mkits.sh: replace echo -e with printfRosen Penev2020-07-111-12/+12
| | | | | | echo flags are not POSIX. printf does the same with added \n. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/gen_image_generic.sh: fix more shellcheck warningsPetr Štetiar2020-07-111-4/+3
| | | | | | | | | | | | | | | | | | Fixes following shellcheck warnings: In scripts/gen_image_generic.sh line 20: cyl=$(( (KERNELSIZE + ROOTFSSIZE) * 1024 * 1024 / (head * sect * 512))) ^-^ SC2034: cyl appears unused. Verify use (or export if used externally). -- In scripts/gen_image_generic.sh line 34: [ -n "$PADDING" ] && dd if=/dev/zero of="$OUTPUT" bs=512 seek="$(($ROOTFSOFFSET + $ROOTFSSIZE))" conv=notrunc count="$sect" ^-----------^ SC2004: $/${} is unnecessary on arithmetic variables. -- In scripts/gen_image_generic.sh line 35: mkfs.fat -n kernel -C "$OUTPUT.kernel" -S 512 "$(($KERNELSIZE / 1024))" ^---------^ SC2004: $/${} is unnecessary on arithmetic variables. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* scripts/gen_image_generic.sh: use /bin/shRosen Penev2020-07-111-1/+1
| | | | | | This has nothing bash specific. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/gen_image_generic.sh: replace -o with if/&&Rosen Penev2020-07-111-2/+2
| | | | | | | | -o is not well defined. Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/env: fix remaining shellcheck warningPetr Štetiar2020-07-111-1/+1
| | | | | | | | | | Fixes following shellcheck warning: In scripts/env line 25: exit ${1:-1} ^-----^ SC2086: Double quote to prevent globbing and word splitting. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* scripts/env: use read -r instead of readRosen Penev2020-07-111-1/+1
| | | | | | | | read mangles backslashes. Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/env: exit in case of failure to cdRosen Penev2020-07-111-1/+1
| | | | | | Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/env: replace \! with !Rosen Penev2020-07-111-2/+2
| | | | | | | The latter is more standard. The former throws an error under shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* scripts/env: use command -v instead of whichRosen Penev2020-07-111-1/+1
| | | | | | | | Simpler and built in to the shell. Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* build: reduce number of files passed to ipk-removeEneas U de Queiroz2020-07-111-11/+8
| | | | | | | | | | | | | | | | | | | | Instead of using xargs to pass a huge number of files to script/ipkg-remove, which will usually pick only one, use a more restrictive wildcard so that, currently, at the most 325 files are examined, instead of up to over 2,300. The 325-file package is python, which is picking up python3* ipks. It is about to be removed. Runner-up is ddns-scripts with 7 files. This makes a second run of make package/luci/compile go from real 16.40s; user 17.42s; sys 2.73s to real 10.71s; user 9.51s; sys 1.27s There is a caveat though: if one were to remove the ABI_VERSION of a package that ends in a digit [0-9], then the old package ipk will not be removed from the bin directory by make package/abc2/clean. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* build: call ipkg-remove using xargs if #args>=512Eneas U de Queiroz2020-07-111-1/+11
| | | | | | | | | | | | | The wildcard call to clean up luci package (luci*) can pick up over 2,300 files when the full tree is built. Running make package/luci/clean or a second run of make package/luci/compile would fail with an 'Argument list too long' error. To avoid that, a maybe_use_xargs function was created that runs the command straight as usual if the number of arguments is < 512, or saves the list in a temporary file and feeds it to xargs otherwise. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* build: package-ipkg: avoid calling wildcard twiceEneas U de Queiroz2020-07-111-2/+8
| | | | | | | | Instead of calling $(wildcard) to check if the removal list is empty, then calling it again to actually remove the files, define a function so that the arguments are expanded only once when it gets called. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 19:21:45 +0000