Merge pull request #381 from azonenberg/countfix

Added better behavioral models for GreenPAK counters. Refactored cells_sim into two files so analog/mixed signal stuff is separate

4 files changed, 900 insertions, 504 deletions

diff --git a/techlibs/greenpak4/Makefile.inc b/techlibs/greenpak4/Makefile.inc
index 7482af6c6..f9614e779 100644
--- a/techlibs/greenpak4/Makefile.inc
+++ b/techlibs/greenpak4/Makefile.inc
@@ -6,4 +6,6 @@ OBJS += techlibs/greenpak4/greenpak4_dffinv.o
 $(eval $(call add_share_file,share/greenpak4,techlibs/greenpak4/cells_latch.v))
 $(eval $(call add_share_file,share/greenpak4,techlibs/greenpak4/cells_map.v))
 $(eval $(call add_share_file,share/greenpak4,techlibs/greenpak4/cells_sim.v))
+$(eval $(call add_share_file,share/greenpak4,techlibs/greenpak4/cells_sim_ams.v))
+$(eval $(call add_share_file,share/greenpak4,techlibs/greenpak4/cells_sim_digital.v))
 $(eval $(call add_share_file,share/greenpak4,techlibs/greenpak4/gp_dff.lib))
diff --git a/techlibs/greenpak4/cells_sim.v b/techlibs/greenpak4/cells_sim.v
index 57f27b44e..2d7bed5cd 100644
--- a/techlibs/greenpak4/cells_sim.v
+++ b/techlibs/greenpak4/cells_sim.v
@@ -1,141 +1,9 @@
 `timescale 1ns/1ps
 
-module GP_2LUT(input IN0, IN1, output OUT);
-	parameter [3:0] INIT = 0;
-	assign OUT = INIT[{IN1, IN0}];
-endmodule
-
-module GP_3LUT(input IN0, IN1, IN2, output OUT);
-	parameter [7:0] INIT = 0;
-	assign OUT = INIT[{IN2, IN1, IN0}];
-endmodule
-
-module GP_4LUT(input IN0, IN1, IN2, IN3, output OUT);
-	parameter [15:0] INIT = 0;
-	assign OUT = INIT[{IN3, IN2, IN1, IN0}];
-endmodule
-
-module GP_ABUF(input wire IN, output wire OUT);
-
-	assign OUT = IN;
-
-	//must be 1, 5, 20, 50
-	//values >1 only available with Vdd > 2.7V
-	parameter BANDWIDTH_KHZ = 1;
-
-	//cannot simulate mixed signal IP
-
-endmodule
-
-module GP_ACMP(input wire PWREN, input wire VIN, input wire VREF, output reg OUT);
-
-	parameter BANDWIDTH = "HIGH";
-	parameter VIN_ATTEN = 1;
-	parameter VIN_ISRC_EN = 0;
-	parameter HYSTERESIS = 0;
-
-	initial OUT = 0;
-
-	//cannot simulate mixed signal IP
-
-endmodule
-
-module GP_BANDGAP(output reg OK);
-	parameter AUTO_PWRDN = 1;
-	parameter CHOPPER_EN = 1;
-	parameter OUT_DELAY = 100;
-
-	//cannot simulate mixed signal IP
-
-endmodule
-
-module GP_CLKBUF(input wire IN, output wire OUT);
-	assign OUT = IN;
-endmodule
-
-module GP_COUNT8(input CLK, input wire RST, output reg OUT, output reg[7:0] POUT);
-
-	parameter RESET_MODE 	= "RISING";
-
-	parameter COUNT_TO		= 8'h1;
-	parameter CLKIN_DIVIDE	= 1;
-
-	//more complex hard IP blocks are not supported for simulation yet
-
-	reg[7:0] count = COUNT_TO;
-
-	//Combinatorially output whenever we wrap low
-	always @(*) begin
-		OUT <= (count == 8'h0);
-		OUT <= count;
-	end
-
-	//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
-	//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
-	//Datasheet seems to indicate that reset is asynchronous, but for now we model as sync due to Yosys issues...
-	always @(posedge CLK) begin
-
-		count		<= count - 1'd1;
-
-		if(count == 0)
-			count	<= COUNT_TO;
-
-		/*
-		if((RESET_MODE == "RISING") && RST)
-			count	<= 0;
-		if((RESET_MODE == "FALLING") && !RST)
-			count	<= 0;
-		if((RESET_MODE == "BOTH") && RST)
-			count	<= 0;
-		*/
-	end
-
-endmodule
-
-module GP_COUNT14(input CLK, input wire RST, output reg OUT);
-
-	parameter RESET_MODE 	= "RISING";
-
-	parameter COUNT_TO		= 14'h1;
-	parameter CLKIN_DIVIDE	= 1;
-
-	//more complex hard IP blocks are not supported for simulation yet
-
-endmodule
-
-module GP_COUNT8_ADV(input CLK, input RST, output reg OUT,
-                     input UP, input KEEP, output reg[7:0] POUT);
-
-	parameter RESET_MODE 	= "RISING";
-	parameter RESET_VALUE   = "ZERO";
-
-	parameter COUNT_TO		= 8'h1;
-	parameter CLKIN_DIVIDE	= 1;
-
-	//more complex hard IP blocks are not supported for simulation yet
-
-endmodule
-
-module GP_COUNT14_ADV(input CLK, input RST, output reg OUT,
-                      input UP, input KEEP, output reg[7:0] POUT);
-
-	parameter RESET_MODE 	= "RISING";
-	parameter RESET_VALUE   = "ZERO";
-
-	parameter COUNT_TO		= 14'h1;
-	parameter CLKIN_DIVIDE	= 1;
+`include "cells_sim_ams.v"
+`include "cells_sim_digital.v"
 
-	//more complex hard IP blocks are not supported for simulation yet
-
-endmodule
-
-module GP_DAC(input[7:0] DIN, input wire VREF, output reg VOUT);
-
-	initial VOUT = 0;
-
-	//analog hard IP is not supported for simulation
-
-endmodule
+//Cells still in this file have INCOMPLETE simulation models, need to finish them
 
 module GP_DCMP(input[7:0] INP, input[7:0] INN, input CLK, input PWRDN, output reg GREATER, output reg EQUAL);
 	parameter PWRDN_SYNC = 1'b0;
@@ -159,237 +27,6 @@ module GP_DCMP(input[7:0] INP, input[7:0] INN, input CLK, input PWRDN, output re
 
 endmodule
 
-module GP_DCMPREF(output reg[7:0]OUT);
-	parameter[7:0] REF_VAL = 8'h00;
-	initial OUT = REF_VAL;
-endmodule
-
-module GP_DCMPMUX(input[1:0] SEL, input[7:0] IN0, input[7:0] IN1, input[7:0] IN2, input[7:0] IN3, output reg[7:0] OUTA, output reg[7:0] OUTB);
-
-	always @(*) begin
-		case(SEL)
-			2'd00: begin
-				OUTA <= IN0;
-				OUTB <= IN3;
-			end
-
-			2'd01: begin
-				OUTA <= IN1;
-				OUTB <= IN2;
-			end
-
-			2'd02: begin
-				OUTA <= IN2;
-				OUTB <= IN1;
-			end
-
-			2'd03: begin
-				OUTA <= IN3;
-				OUTB <= IN0;
-			end
-
-		endcase
-	end
-endmodule
-
-module GP_DELAY(input IN, output reg OUT);
-
-	parameter DELAY_STEPS = 1;
-	parameter GLITCH_FILTER = 0;
-
-	initial OUT = 0;
-
-	generate
-
-		//TODO: These delays are PTV dependent! For now, hard code 3v3 timing
-		//Change simulation-mode delay depending on global Vdd range (how to specify this?)
-		always @(*) begin
-			case(DELAY_STEPS)
-				1: #166 OUT = IN;
-				2: #318 OUT = IN;
-				2: #471 OUT = IN;
-				3: #622 OUT = IN;
-				default: begin
-					$display("ERROR: GP_DELAY must have DELAY_STEPS in range [1,4]");
-					$finish;
-				end
-			endcase
-		end
-
-	endgenerate
-
-endmodule
-
-module GP_DFF(input D, CLK, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	initial Q = INIT;
-	always @(posedge CLK) begin
-		Q <= D;
-	end
-endmodule
-
-module GP_DFFI(input D, CLK, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	initial nQ = INIT;
-	always @(posedge CLK) begin
-		nQ <= ~D;
-	end
-endmodule
-
-module GP_DFFR(input D, CLK, nRST, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	initial Q = INIT;
-	always @(posedge CLK, negedge nRST) begin
-		if (!nRST)
-			Q <= 1'b0;
-		else
-			Q <= D;
-	end
-endmodule
-
-module GP_DFFRI(input D, CLK, nRST, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	initial nQ = INIT;
-	always @(posedge CLK, negedge nRST) begin
-		if (!nRST)
-			nQ <= 1'b1;
-		else
-			nQ <= ~D;
-	end
-endmodule
-
-module GP_DFFS(input D, CLK, nSET, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	initial Q = INIT;
-	always @(posedge CLK, negedge nSET) begin
-		if (!nSET)
-			Q <= 1'b1;
-		else
-			Q <= D;
-	end
-endmodule
-
-module GP_DFFSI(input D, CLK, nSET, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	initial nQ = INIT;
-	always @(posedge CLK, negedge nSET) begin
-		if (!nSET)
-			nQ <= 1'b0;
-		else
-			nQ <= ~D;
-	end
-endmodule
-
-module GP_DFFSR(input D, CLK, nSR, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	parameter [0:0] SRMODE = 1'bx;
-	initial Q = INIT;
-	always @(posedge CLK, negedge nSR) begin
-		if (!nSR)
-			Q <= SRMODE;
-		else
-			Q <= D;
-	end
-endmodule
-
-module GP_DFFSRI(input D, CLK, nSR, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	parameter [0:0] SRMODE = 1'bx;
-	initial nQ = INIT;
-	always @(posedge CLK, negedge nSR) begin
-		if (!nSR)
-			nQ <= ~SRMODE;
-		else
-			nQ <= ~D;
-	end
-endmodule
-
-module GP_DLATCH(input D, input nCLK, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	initial Q = INIT;
-	always @(*) begin
-		if(!nCLK)
-			Q <= D;
-	end
-endmodule
-
-module GP_DLATCHI(input D, input nCLK, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	initial nQ = INIT;
-	always @(*) begin
-		if(!nCLK)
-			nQ <= ~D;
-	end
-endmodule
-
-module GP_DLATCHR(input D, input nCLK, input nRST, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	initial Q = INIT;
-	always @(*) begin
-		if(!nRST)
-			Q <= 1'b0;
-		else if(!nCLK)
-			Q <= D;
-	end
-endmodule
-
-module GP_DLATCHRI(input D, input nCLK, input nRST, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	initial nQ = INIT;
-	always @(*) begin
-		if(!nRST)
-			nQ <= 1'b1;
-		else if(!nCLK)
-			nQ <= ~D;
-	end
-endmodule
-
-module GP_DLATCHS(input D, input nCLK, input nSET, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	initial Q = INIT;
-	always @(*) begin
-		if(!nSET)
-			Q <= 1'b1;
-		else if(!nCLK)
-			Q <= D;
-	end
-endmodule
-
-module GP_DLATCHSI(input D, input nCLK, input nSET, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	initial nQ = INIT;
-	always @(*) begin
-		if(!nSET)
-			nQ <= 1'b0;
-		else if(!nCLK)
-			nQ <= ~D;
-	end
-endmodule
-
-module GP_DLATCHSR(input D, input nCLK, input nSR, output reg Q);
-	parameter [0:0] INIT = 1'bx;
-	parameter[0:0] SRMODE = 1'bx;
-	initial Q = INIT;
-	always @(*) begin
-		if(!nSR)
-			Q <= SRMODE;
-		else if(!nCLK)
-			Q <= D;
-	end
-endmodule
-
-module GP_DLATCHSRI(input D, input nCLK, input nSR, output reg nQ);
-	parameter [0:0] INIT = 1'bx;
-	parameter[0:0] SRMODE = 1'bx;
-	initial nQ = INIT;
-	always @(*) begin
-		if(!nSR)
-			nQ <= ~SRMODE;
-		else if(!nCLK)
-			nQ <= ~D;
-	end
-endmodule
-
 module GP_EDGEDET(input IN, output reg OUT);
 
 	parameter EDGE_DIRECTION = "RISING";
@@ -400,107 +37,6 @@ module GP_EDGEDET(input IN, output reg OUT);
 
 endmodule
 
-module GP_IBUF(input IN, output OUT);
-	assign OUT = IN;
-endmodule
-
-module GP_IOBUF(input IN, input OE, output OUT, inout IO);
-	assign OUT = IO;
-	assign IO = OE ? IN : 1'bz;
-endmodule
-
-module GP_INV(input IN, output OUT);
-	assign OUT = ~IN;
-endmodule
-
-module GP_LFOSC(input PWRDN, output reg CLKOUT);
-
-	parameter PWRDN_EN = 0;
-	parameter AUTO_PWRDN = 0;
-	parameter OUT_DIV = 1;
-
-	initial CLKOUT = 0;
-
-	//auto powerdown not implemented for simulation
-	//output dividers not implemented for simulation
-
-	always begin
-		if(PWRDN)
-			CLKOUT = 0;
-		else begin
-			//half period of 1730 Hz
-			#289017;
-			CLKOUT = ~CLKOUT;
-		end
-	end
-
-endmodule
-
-module GP_OBUF(input IN, output OUT);
-	assign OUT = IN;
-endmodule
-
-module GP_OBUFT(input IN, input OE, output OUT);
-	assign OUT = OE ? IN : 1'bz;
-endmodule
-
-module GP_PGA(input wire VIN_P, input wire VIN_N, input wire VIN_SEL, output reg VOUT);
-
-	parameter GAIN = 1;
-	parameter INPUT_MODE = "SINGLE";
-
-	initial VOUT = 0;
-
-	//cannot simulate mixed signal IP
-
-endmodule
-
-module GP_PGEN(input wire nRST, input wire CLK, output reg OUT);
-	initial OUT = 0;
-	parameter PATTERN_DATA = 16'h0;
-	parameter PATTERN_LEN = 5'd16;
-
-	reg[3:0] count = 0;
-	always @(posedge CLK) begin
-		if(!nRST)
-			OUT <= PATTERN_DATA[0];
-
-		else begin
-			count <= count + 1;
-			OUT <= PATTERN_DATA[count];
-
-			if( (count + 1) == PATTERN_LEN)
-				count <= 0;
-		end
-	end
-
-endmodule
-
-module GP_PWRDET(output reg VDD_LOW);
-	initial VDD_LOW = 0;
-endmodule
-
-module GP_POR(output reg RST_DONE);
-	parameter POR_TIME = 500;
-
-	initial begin
-		RST_DONE = 0;
-
-		if(POR_TIME == 4)
-			#4000;
-		else if(POR_TIME == 500)
-			#500000;
-		else begin
-			$display("ERROR: bad POR_TIME for GP_POR cell");
-			$finish;
-		end
-
-		RST_DONE = 1;
-
-	end
-
-endmodule
-
 module GP_RCOSC(input PWRDN, output reg CLKOUT_HARDIP, output reg CLKOUT_FABRIC);
 
 	parameter PWRDN_EN = 0;
@@ -567,29 +103,6 @@ module GP_RINGOSC(input PWRDN, output reg CLKOUT_HARDIP, output reg CLKOUT_FABRI
 
 endmodule
 
-module GP_SHREG(input nRST, input CLK, input IN, output OUTA, output OUTB);
-
-	parameter OUTA_TAP = 1;
-	parameter OUTA_INVERT = 0;
-	parameter OUTB_TAP = 1;
-
-	reg[15:0] shreg = 0;
-
-	always @(posedge CLK, negedge nRST) begin
-
-		if(!nRST)
-			shreg = 0;
-
-		else
-			shreg <= {shreg[14:0], IN};
-
-	end
-
-	assign OUTA = (OUTA_INVERT) ? ~shreg[OUTA_TAP - 1] : shreg[OUTA_TAP - 1];
-	assign OUTB = shreg[OUTB_TAP - 1];
-
-endmodule
-
 module GP_SPI(
 	input SCK,
 	inout SDAT,
@@ -625,17 +138,3 @@ module GP_SYSRESET(input RST);
 	//cannot simulate whole system reset
 
 endmodule
-
-module GP_VDD(output OUT);
-       assign OUT = 1;
-endmodule
-
-module GP_VREF(input VIN, output reg VOUT);
-	parameter VIN_DIV = 1;
-	parameter VREF = 0;
-	//cannot simulate mixed signal IP
-endmodule
-
-module GP_VSS(output OUT);
-       assign OUT = 0;
-endmodule
diff --git a/techlibs/greenpak4/cells_sim_ams.v b/techlibs/greenpak4/cells_sim_ams.v
new file mode 100644
index 000000000..7f8b3de3b
--- /dev/null
+++ b/techlibs/greenpak4/cells_sim_ams.v
@@ -0,0 +1,110 @@
+`timescale 1ns/1ps
+
+/*
+ This file contains analog / mixed signal cells, or other things that are not possible to fully model
+ in behavioral Verilog.
+
+ It also contains some stuff like oscillators that use non-synthesizeable constructs such as delays.
+ TODO: do we want a third file for those cells?
+ */
+
+module GP_ABUF(input wire IN, output wire OUT);
+
+	assign OUT = IN;
+
+	//must be 1, 5, 20, 50
+	//values >1 only available with Vdd > 2.7V
+	parameter BANDWIDTH_KHZ = 1;
+
+endmodule
+
+module GP_ACMP(input wire PWREN, input wire VIN, input wire VREF, output reg OUT);
+
+	parameter BANDWIDTH = "HIGH";
+	parameter VIN_ATTEN = 1;
+	parameter VIN_ISRC_EN = 0;
+	parameter HYSTERESIS = 0;
+
+	initial OUT = 0;
+
+endmodule
+
+module GP_BANDGAP(output reg OK);
+	parameter AUTO_PWRDN = 1;
+	parameter CHOPPER_EN = 1;
+	parameter OUT_DELAY = 100;
+
+endmodule
+
+module GP_DAC(input[7:0] DIN, input wire VREF, output reg VOUT);
+
+	initial VOUT = 0;
+
+	//analog hard IP is not supported for simulation
+
+endmodule
+
+module GP_LFOSC(input PWRDN, output reg CLKOUT);
+
+	parameter PWRDN_EN = 0;
+	parameter AUTO_PWRDN = 0;
+	parameter OUT_DIV = 1;
+
+	initial CLKOUT = 0;
+
+	//auto powerdown not implemented for simulation
+	//output dividers not implemented for simulation
+
+	always begin
+		if(PWRDN)
+			CLKOUT = 0;
+		else begin
+			//half period of 1730 Hz
+			#289017;
+			CLKOUT = ~CLKOUT;
+		end
+	end
+
+endmodule
+
+module GP_PGA(input wire VIN_P, input wire VIN_N, input wire VIN_SEL, output reg VOUT);
+
+	parameter GAIN = 1;
+	parameter INPUT_MODE = "SINGLE";
+
+	initial VOUT = 0;
+
+	//cannot simulate mixed signal IP
+
+endmodule
+
+module GP_PWRDET(output reg VDD_LOW);
+	initial VDD_LOW = 0;
+endmodule
+
+module GP_VREF(input VIN, output reg VOUT);
+	parameter VIN_DIV = 1;
+	parameter VREF = 0;
+	//cannot simulate mixed signal IP
+endmodule
+
+module GP_POR(output reg RST_DONE);
+	parameter POR_TIME = 500;
+
+	initial begin
+		RST_DONE = 0;
+
+		if(POR_TIME == 4)
+			#4000;
+		else if(POR_TIME == 500)
+			#500000;
+		else begin
+			$display("ERROR: bad POR_TIME for GP_POR cell");
+			$finish;
+		end
+
+		RST_DONE = 1;
+
+	end
+
+endmodule
diff --git a/techlibs/greenpak4/cells_sim_digital.v b/techlibs/greenpak4/cells_sim_digital.v
new file mode 100644
index 000000000..3ed80005b
--- /dev/null
+++ b/techlibs/greenpak4/cells_sim_digital.v
@@ -0,0 +1,785 @@
+`timescale 1ns/1ps
+
+/*
+ This file contains simulation models for GreenPAK cells which are possible to fully model using synthesizeable
+ behavioral Verilog constructs only.
+ */
+
+module GP_2LUT(input IN0, IN1, output OUT);
+	parameter [3:0] INIT = 0;
+	assign OUT = INIT[{IN1, IN0}];
+endmodule
+
+module GP_3LUT(input IN0, IN1, IN2, output OUT);
+	parameter [7:0] INIT = 0;
+	assign OUT = INIT[{IN2, IN1, IN0}];
+endmodule
+
+module GP_4LUT(
+	input wire IN0,
+	input wire IN1,
+	input wire IN2,
+	input wire IN3,
+	output wire OUT);
+
+	parameter [15:0] INIT = 0;
+	assign OUT = INIT[{IN3, IN2, IN1, IN0}];
+endmodule
+
+module GP_CLKBUF(input wire IN, output wire OUT);
+	assign OUT = IN;
+endmodule
+
+module GP_COUNT14(input CLK, input wire RST, output reg OUT);
+
+	parameter RESET_MODE 	= "RISING";
+
+	parameter COUNT_TO		= 14'h1;
+	parameter CLKIN_DIVIDE	= 1;
+
+	reg[13:0] count = COUNT_TO;
+
+	initial begin
+		if(CLKIN_DIVIDE != 1) begin
+			$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
+			$finish;
+		end
+	end
+
+	//Combinatorially output underflow flag whenever we wrap low
+	always @(*) begin
+		OUT <= (count == 14'h0);
+	end
+
+	//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
+	//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
+	generate
+		case(RESET_MODE)
+
+			"RISING": begin
+				always @(posedge CLK, posedge RST) begin
+					count		<= count - 1'd1;
+					if(count == 0)
+						count	<= COUNT_TO;
+
+					if(RST)
+						count	<= 0;
+				end
+			end
+
+			"FALLING": begin
+				always @(posedge CLK, negedge RST) begin
+					count		<= count - 1'd1;
+					if(count == 0)
+						count	<= COUNT_TO;
+
+					if(!RST)
+						count	<= 0;
+				end
+			end
+
+			"BOTH": begin
+				initial begin
+					$display("Both-edge reset mode for GP_COUNT14 not implemented");
+					$finish;
+				end
+			end
+
+			"LEVEL": begin
+				always @(posedge CLK, posedge RST) begin
+					if(RST)
+						count	<= 0;
+
+					else begin
+						count		<= count - 1'd1;
+						if(count == 0)
+							count	<= COUNT_TO;
+					end
+				end
+			end
+
+			default: begin
+				initial begin
+					$display("Invalid RESET_MODE on GP_COUNT8");
+					$finish;
+				end
+			end
+
+		endcase
+	endgenerate
+
+endmodule
+
+module GP_COUNT14_ADV(input CLK, input RST, output reg OUT,
+                     input UP, input KEEP, output reg[7:0] POUT);
+
+	parameter RESET_MODE 	= "RISING";
+	parameter RESET_VALUE   = "ZERO";
+
+	parameter COUNT_TO		= 14'h1;
+	parameter CLKIN_DIVIDE	= 1;
+
+	initial begin
+		if(CLKIN_DIVIDE != 1) begin
+			$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
+			$finish;
+		end
+	end
+
+	reg[13:0] count = COUNT_TO;
+
+	//Combinatorially output underflow flag whenever we wrap low
+	always @(*) begin
+		if(UP)
+			OUT <= (count == 14'h3fff);
+		else
+			OUT <= (count == 14'h0);
+		POUT <= count[7:0];
+	end
+
+	//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
+	//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
+	generate
+		case(RESET_MODE)
+
+			"RISING": begin
+				always @(posedge CLK, posedge RST) begin
+
+					//Main counter
+					if(KEEP) begin
+					end
+					else if(UP)
+						count		<= count + 1'd1;
+					else
+						count		<= count - 1'd1;
+
+					//Wrapping
+					if(count == 0 && !UP)
+						count	<= COUNT_TO;
+					if(count == 14'h3fff && UP)
+						count	<= COUNT_TO;
+
+					//Resets
+					if(RST) begin
+						if(RESET_VALUE == "ZERO")
+							count	<= 0;
+						else
+							count	<= COUNT_TO;
+					end
+
+				end
+			end
+
+			"FALLING": begin
+				always @(posedge CLK, negedge RST) begin
+
+					//Main counter
+					if(KEEP) begin
+					end
+					else if(UP)
+						count		<= count + 1'd1;
+					else
+						count		<= count - 1'd1;
+
+					//Wrapping
+					if(count == 0 && !UP)
+						count	<= COUNT_TO;
+					if(count == 14'h3fff && UP)
+						count	<= COUNT_TO;
+
+					//Resets
+					if(!RST) begin
+						if(RESET_VALUE == "ZERO")
+							count	<= 0;
+						else
+							count	<= COUNT_TO;
+					end
+
+				end
+			end
+
+			"BOTH": begin
+				initial begin
+					$display("Both-edge reset mode for GP_COUNT14_ADV not implemented");
+					$finish;
+				end
+			end
+
+			"LEVEL": begin
+				always @(posedge CLK, posedge RST) begin
+
+					//Resets
+					if(RST) begin
+						if(RESET_VALUE == "ZERO")
+							count	<= 0;
+						else
+							count	<= COUNT_TO;
+					end
+
+					else begin
+
+						//Main counter
+						if(KEEP) begin
+						end
+						else if(UP)
+							count		<= count + 1'd1;
+						else
+							count		<= count - 1'd1;
+
+						//Wrapping
+						if(count == 0 && !UP)
+							count	<= COUNT_TO;
+						if(count == 14'h3fff && UP)
+							count	<= COUNT_TO;
+
+					end
+
+				end
+			end
+
+			default: begin
+				initial begin
+					$display("Invalid RESET_MODE on GP_COUNT14_ADV");
+					$finish;
+				end
+			end
+
+		endcase
+	endgenerate
+
+endmodule
+
+module GP_COUNT8_ADV(input CLK, input RST, output reg OUT,
+                     input UP, input KEEP, output reg[7:0] POUT);
+
+	parameter RESET_MODE 	= "RISING";
+	parameter RESET_VALUE   = "ZERO";
+
+	parameter COUNT_TO		= 8'h1;
+	parameter CLKIN_DIVIDE	= 1;
+
+	reg[7:0] count = COUNT_TO;
+
+	initial begin
+		if(CLKIN_DIVIDE != 1) begin
+			$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
+			$finish;
+		end
+	end
+
+	//Combinatorially output underflow flag whenever we wrap low
+	always @(*) begin
+		if(UP)
+			OUT <= (count == 8'hff);
+		else
+			OUT <= (count == 8'h0);
+		POUT <= count;
+	end
+
+	//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
+	//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
+	generate
+		case(RESET_MODE)
+
+			"RISING": begin
+				always @(posedge CLK, posedge RST) begin
+
+					//Main counter
+					if(KEEP) begin
+					end
+					else if(UP)
+						count		<= count + 1'd1;
+					else
+						count		<= count - 1'd1;
+
+					//Wrapping
+					if(count == 0 && !UP)
+						count	<= COUNT_TO;
+					if(count == 8'hff && UP)
+						count	<= COUNT_TO;
+
+					//Resets
+					if(RST) begin
+						if(RESET_VALUE == "ZERO")
+							count	<= 0;
+						else
+							count	<= COUNT_TO;
+					end
+
+				end
+			end
+
+			"FALLING": begin
+				always @(posedge CLK, negedge RST) begin
+
+					//Main counter
+					if(KEEP) begin
+					end
+					else if(UP)
+						count		<= count + 1'd1;
+					else
+						count		<= count - 1'd1;
+
+					//Wrapping
+					if(count == 0 && !UP)
+						count	<= COUNT_TO;
+					if(count == 8'hff && UP)
+						count	<= COUNT_TO;
+
+					//Resets
+					if(!RST) begin
+						if(RESET_VALUE == "ZERO")
+							count	<= 0;
+						else
+							count	<= COUNT_TO;
+					end
+
+				end
+			end
+
+			"BOTH": begin
+				initial begin
+					$display("Both-edge reset mode for GP_COUNT8_ADV not implemented");
+					$finish;
+				end
+			end
+
+			"LEVEL": begin
+				always @(posedge CLK, posedge RST) begin
+
+					//Resets
+					if(RST) begin
+						if(RESET_VALUE == "ZERO")
+							count	<= 0;
+						else
+							count	<= COUNT_TO;
+					end
+
+					else begin
+
+						//Main counter
+						if(KEEP) begin
+						end
+						else if(UP)
+							count		<= count + 1'd1;
+						else
+							count		<= count - 1'd1;
+
+						//Wrapping
+						if(count == 0 && !UP)
+							count	<= COUNT_TO;
+						if(count == 8'hff && UP)
+							count	<= COUNT_TO;
+
+					end
+
+				end
+			end
+
+			default: begin
+				initial begin
+					$display("Invalid RESET_MODE on GP_COUNT8_ADV");
+					$finish;
+				end
+			end
+
+		endcase
+	endgenerate
+
+endmodule
+
+module GP_COUNT8(
+	input wire CLK,
+	input wire RST,
+	output reg OUT,
+	output reg[7:0] POUT);
+
+	parameter RESET_MODE 	= "RISING";
+
+	parameter COUNT_TO		= 8'h1;
+	parameter CLKIN_DIVIDE	= 1;
+
+	initial begin
+		if(CLKIN_DIVIDE != 1) begin
+			$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
+			$finish;
+		end
+	end
+
+	reg[7:0] count = COUNT_TO;
+
+	//Combinatorially output underflow flag whenever we wrap low
+	always @(*) begin
+		OUT <= (count == 8'h0);
+		POUT <= count;
+	end
+
+	//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
+	//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
+	generate
+		case(RESET_MODE)
+
+			"RISING": begin
+				always @(posedge CLK, posedge RST) begin
+					count		<= count - 1'd1;
+					if(count == 0)
+						count	<= COUNT_TO;
+
+					if(RST)
+						count	<= 0;
+				end
+			end
+
+			"FALLING": begin
+				always @(posedge CLK, negedge RST) begin
+					count		<= count - 1'd1;
+					if(count == 0)
+						count	<= COUNT_TO;
+
+					if(!RST)
+						count	<= 0;
+				end
+			end
+
+			"BOTH": begin
+				initial begin
+					$display("Both-edge reset mode for GP_COUNT8 not implemented");
+					$finish;
+				end
+			end
+
+			"LEVEL": begin
+				always @(posedge CLK, posedge RST) begin
+					if(RST)
+						count	<= 0;
+
+					else begin
+						count		<= count - 1'd1;
+						if(count == 0)
+							count	<= COUNT_TO;
+					end
+				end
+			end
+
+			default: begin
+				initial begin
+					$display("Invalid RESET_MODE on GP_COUNT8");
+					$finish;
+				end
+			end
+
+		endcase
+	endgenerate
+
+endmodule
+
+module GP_DCMPREF(output reg[7:0]OUT);
+	parameter[7:0] REF_VAL = 8'h00;
+	initial OUT = REF_VAL;
+endmodule
+
+module GP_DCMPMUX(input[1:0] SEL, input[7:0] IN0, input[7:0] IN1, input[7:0] IN2, input[7:0] IN3, output reg[7:0] OUTA, output reg[7:0] OUTB);
+
+	always @(*) begin
+		case(SEL)
+			2'd00: begin
+				OUTA <= IN0;
+				OUTB <= IN3;
+			end
+
+			2'd01: begin
+				OUTA <= IN1;
+				OUTB <= IN2;
+			end
+
+			2'd02: begin
+				OUTA <= IN2;
+				OUTB <= IN1;
+			end
+
+			2'd03: begin
+				OUTA <= IN3;
+				OUTB <= IN0;
+			end
+
+		endcase
+	end
+endmodule
+
+module GP_DELAY(input IN, output reg OUT);
+
+	parameter DELAY_STEPS = 1;
+	parameter GLITCH_FILTER = 0;
+
+	initial OUT = 0;
+
+	generate
+
+		if(GLITCH_FILTER) begin
+			initial begin
+				$display("ERROR: GP_DELAY glitch filter mode not implemented");
+				$finish;
+			end
+		end
+
+		//TODO: These delays are PTV dependent! For now, hard code 3v3 timing
+		//Change simulation-mode delay depending on global Vdd range (how to specify this?)
+		always @(*) begin
+			case(DELAY_STEPS)
+				1: #166 OUT = IN;
+				2: #318 OUT = IN;
+				2: #471 OUT = IN;
+				3: #622 OUT = IN;
+				default: begin
+					$display("ERROR: GP_DELAY must have DELAY_STEPS in range [1,4]");
+					$finish;
+				end
+			endcase
+		end
+
+	endgenerate
+
+endmodule
+
+module GP_DFF(input D, CLK, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	initial Q = INIT;
+	always @(posedge CLK) begin
+		Q <= D;
+	end
+endmodule
+
+module GP_DFFI(input D, CLK, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	initial nQ = INIT;
+	always @(posedge CLK) begin
+		nQ <= ~D;
+	end
+endmodule
+
+module GP_DFFR(input D, CLK, nRST, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	initial Q = INIT;
+	always @(posedge CLK, negedge nRST) begin
+		if (!nRST)
+			Q <= 1'b0;
+		else
+			Q <= D;
+	end
+endmodule
+
+module GP_DFFRI(input D, CLK, nRST, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	initial nQ = INIT;
+	always @(posedge CLK, negedge nRST) begin
+		if (!nRST)
+			nQ <= 1'b1;
+		else
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_DFFS(input D, CLK, nSET, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	initial Q = INIT;
+	always @(posedge CLK, negedge nSET) begin
+		if (!nSET)
+			Q <= 1'b1;
+		else
+			Q <= D;
+	end
+endmodule
+
+module GP_DFFSI(input D, CLK, nSET, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	initial nQ = INIT;
+	always @(posedge CLK, negedge nSET) begin
+		if (!nSET)
+			nQ <= 1'b0;
+		else
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_DFFSR(input D, CLK, nSR, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	parameter [0:0] SRMODE = 1'bx;
+	initial Q = INIT;
+	always @(posedge CLK, negedge nSR) begin
+		if (!nSR)
+			Q <= SRMODE;
+		else
+			Q <= D;
+	end
+endmodule
+
+module GP_DFFSRI(input D, CLK, nSR, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	parameter [0:0] SRMODE = 1'bx;
+	initial nQ = INIT;
+	always @(posedge CLK, negedge nSR) begin
+		if (!nSR)
+			nQ <= ~SRMODE;
+		else
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_DLATCH(input D, input nCLK, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	initial Q = INIT;
+	always @(*) begin
+		if(!nCLK)
+			Q <= D;
+	end
+endmodule
+
+module GP_DLATCHI(input D, input nCLK, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	initial nQ = INIT;
+	always @(*) begin
+		if(!nCLK)
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_DLATCHR(input D, input nCLK, input nRST, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	initial Q = INIT;
+	always @(*) begin
+		if(!nRST)
+			Q <= 1'b0;
+		else if(!nCLK)
+			Q <= D;
+	end
+endmodule
+
+module GP_DLATCHRI(input D, input nCLK, input nRST, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	initial nQ = INIT;
+	always @(*) begin
+		if(!nRST)
+			nQ <= 1'b1;
+		else if(!nCLK)
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_DLATCHS(input D, input nCLK, input nSET, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	initial Q = INIT;
+	always @(*) begin
+		if(!nSET)
+			Q <= 1'b1;
+		else if(!nCLK)
+			Q <= D;
+	end
+endmodule
+
+module GP_DLATCHSI(input D, input nCLK, input nSET, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	initial nQ = INIT;
+	always @(*) begin
+		if(!nSET)
+			nQ <= 1'b0;
+		else if(!nCLK)
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_DLATCHSR(input D, input nCLK, input nSR, output reg Q);
+	parameter [0:0] INIT = 1'bx;
+	parameter[0:0] SRMODE = 1'bx;
+	initial Q = INIT;
+	always @(*) begin
+		if(!nSR)
+			Q <= SRMODE;
+		else if(!nCLK)
+			Q <= D;
+	end
+endmodule
+
+module GP_DLATCHSRI(input D, input nCLK, input nSR, output reg nQ);
+	parameter [0:0] INIT = 1'bx;
+	parameter[0:0] SRMODE = 1'bx;
+	initial nQ = INIT;
+	always @(*) begin
+		if(!nSR)
+			nQ <= ~SRMODE;
+		else if(!nCLK)
+			nQ <= ~D;
+	end
+endmodule
+
+module GP_IBUF(input IN, output OUT);
+	assign OUT = IN;
+endmodule
+
+module GP_IOBUF(input IN, input OE, output OUT, inout IO);
+	assign OUT = IO;
+	assign IO = OE ? IN : 1'bz;
+endmodule
+
+module GP_INV(input IN, output OUT);
+	assign OUT = ~IN;
+endmodule
+
+module GP_OBUF(input IN, output OUT);
+	assign OUT = IN;
+endmodule
+
+module GP_OBUFT(input IN, input OE, output OUT);
+	assign OUT = OE ? IN : 1'bz;
+endmodule
+
+module GP_PGEN(input wire nRST, input wire CLK, output reg OUT);
+	initial OUT = 0;
+	parameter PATTERN_DATA = 16'h0;
+	parameter PATTERN_LEN = 5'd16;
+
+	reg[3:0] count = 0;
+	always @(posedge CLK) begin
+		if(!nRST)
+			OUT <= PATTERN_DATA[0];
+
+		else begin
+			count <= count + 1;
+			OUT <= PATTERN_DATA[count];
+
+			if( (count + 1) == PATTERN_LEN)
+				count <= 0;
+		end
+	end
+
+endmodule
+
+module GP_SHREG(input nRST, input CLK, input IN, output OUTA, output OUTB);
+
+	parameter OUTA_TAP = 1;
+	parameter OUTA_INVERT = 0;
+	parameter OUTB_TAP = 1;
+
+	reg[15:0] shreg = 0;
+
+	always @(posedge CLK, negedge nRST) begin
+
+		if(!nRST)
+			shreg = 0;
+
+		else
+			shreg <= {shreg[14:0], IN};
+
+	end
+
+	assign OUTA = (OUTA_INVERT) ? ~shreg[OUTA_TAP - 1] : shreg[OUTA_TAP - 1];
+	assign OUTB = shreg[OUTB_TAP - 1];
+
+endmodule
+
+module GP_VDD(output OUT);
+       assign OUT = 1;
+endmodule
+
+module GP_VSS(output OUT);
+       assign OUT = 0;
+endmodule