diff options
Diffstat (limited to 'os/hal/boards/ST_NUCLEO_F103RB/board.h')
| -rw-r--r-- | os/hal/boards/ST_NUCLEO_F103RB/board.h | 202 |
1 files changed, 0 insertions, 202 deletions
diff --git a/os/hal/boards/ST_NUCLEO_F103RB/board.h b/os/hal/boards/ST_NUCLEO_F103RB/board.h deleted file mode 100644 index 61c580222..000000000 --- a/os/hal/boards/ST_NUCLEO_F103RB/board.h +++ /dev/null @@ -1,202 +0,0 @@ -/*
- ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Setup for the ST INEMO-M1 Discovery board.
- */
-
-/*
- * Board identifier.
- */
-#define BOARD_ST_NUCLEO_F103RB
-#define BOARD_NAME "STMicroelectronics NUCLEO-F103RB"
-
-/*
- * Board frequencies.
- */
-#define STM32_LSECLK 0
-
-#if defined(NUCLEO_EXTERNAL_OSCILLATOR)
-#define STM32_HSECLK 8000000
-#define STM32_HSE_BYPASS
-
-#elif defined(NUCLEO_HSE_CRYSTAL)
-#define STM32_HSECLK 8000000
-
-#else
-#define STM32_HSECLK 0
-#endif
-
-/*
- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
- */
-#define STM32F103xB
-
-/*
- * IO pins assignments.
- */
-#define GPIOA_PA0 0
-#define GPIOA_PA1 1
-#define GPIOA_USART_TX 2
-#define GPIOA_USART_RX 3
-#define GPIOA_PA4 4
-#define GPIOA_LED_GREEN 5
-#define GPIOA_PA6 6
-#define GPIOA_PA7 7
-#define GPIOA_PA8 8
-#define GPIOA_PA9 9
-#define GPIOA_PA10 10
-#define GPIOA_PA11 11
-#define GPIOA_PA12 12
-#define GPIOA_SWDIO 13
-#define GPIOA_SWCLK 14
-#define GPIOA_PA15 15
-
-#define GPIOB_PB0 0
-#define GPIOB_PB1 1
-#define GPIOB_PB2 2
-#define GPIOB_SWO 3
-#define GPIOB_PB4 4
-#define GPIOB_PB5 5
-#define GPIOB_PB6 6
-#define GPIOB_PB7 7
-#define GPIOB_PB8 8
-#define GPIOB_PB9 9
-#define GPIOB_PB10 10
-#define GPIOB_PB11 11
-#define GPIOB_PB12 12
-#define GPIOB_PB13 13
-#define GPIOB_PB14 14
-#define GPIOB_PB15 15
-
-#define GPIOC_PC0 0
-#define GPIOC_PC1 1
-#define GPIOC_PC2 2
-#define GPIOC_PC3 3
-#define GPIOC_PC4 4
-#define GPIOC_PC5 5
-#define GPIOC_PC6 6
-#define GPIOC_PC7 7
-#define GPIOC_PC8 8
-#define GPIOC_PC9 9
-#define GPIOC_PC10 10
-#define GPIOC_PC11 11
-#define GPIOC_PC12 12
-#define GPIOC_BUTTON 13
-#define GPIOC_PC14 14
-#define GPIOC_PC15 15
-
-#define GPIOD_OSC_IN 0
-#define GPIOD_OSC_OUT 1
-#define GPIOD_PD2 2
-
-/*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- * 0 - Analog input.
- * 1 - Push Pull output 10MHz.
- * 2 - Push Pull output 2MHz.
- * 3 - Push Pull output 50MHz.
- * 4 - Digital input.
- * 5 - Open Drain output 10MHz.
- * 6 - Open Drain output 2MHz.
- * 7 - Open Drain output 50MHz.
- * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
- * 9 - Alternate Push Pull output 10MHz.
- * A - Alternate Push Pull output 2MHz.
- * B - Alternate Push Pull output 50MHz.
- * C - Reserved.
- * D - Alternate Open Drain output 10MHz.
- * E - Alternate Open Drain output 2MHz.
- * F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
-/*
- * Port A setup.
- * Everything input with pull-up except:
- * PA2 - Alternate output (GPIOA_USART_TX).
- * PA3 - Normal input (GPIOA_USART_RX).
- * PA5 - Push Pull output (GPIOA_LED_GREEN).
- * PA13 - Pull-up input (GPIOA_SWDIO).
- * PA14 - Pull-down input (GPIOA_SWCLK).
- */
-#define VAL_GPIOACRL 0x88384B88 /* PA7...PA0 */
-#define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
-#define VAL_GPIOAODR 0xFFFFBFDF
-
-/*
- * Port B setup.
- * Everything input with pull-up except:
- * PB3 - Pull-up input (GPIOA_SWO).
- */
-#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
-#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
-#define VAL_GPIOBODR 0xFFFFFFFF
-
-/*
- * Port C setup.
- * Everything input with pull-up except:
- * PC13 - Normal input (GPIOC_BUTTON).
- */
-#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
-#define VAL_GPIOCCRH 0x88488888 /* PC15...PC8 */
-#define VAL_GPIOCODR 0xFFFFFFFF
-
-/*
- * Port D setup.
- * Everything input with pull-up except:
- * PD0 - Normal input (GPIOD_OSC_IN).
- * PD1 - Normal input (GPIOD_OSC_OUT).
- */
-#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
-#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
-#define VAL_GPIODODR 0xFFFFFFFF
-
-/*
- * Port E setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
-#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
-#define VAL_GPIOEODR 0xFFFFFFFF
-
-/*
- * USB bus activation macro, required by the USB driver.
- */
-#define usb_lld_connect_bus(usbp)
-
-/*
- * USB bus de-activation macro, required by the USB driver.
- */
-#define usb_lld_disconnect_bus(usbp)
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
- void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */
|