blob: 61c580222b7f00b0bd6e309f2f47bdfc040795d8 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
|
/*
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for the ST INEMO-M1 Discovery board.
*/
/*
* Board identifier.
*/
#define BOARD_ST_NUCLEO_F103RB
#define BOARD_NAME "STMicroelectronics NUCLEO-F103RB"
/*
* Board frequencies.
*/
#define STM32_LSECLK 0
#if defined(NUCLEO_EXTERNAL_OSCILLATOR)
#define STM32_HSECLK 8000000
#define STM32_HSE_BYPASS
#elif defined(NUCLEO_HSE_CRYSTAL)
#define STM32_HSECLK 8000000
#else
#define STM32_HSECLK 0
#endif
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*/
#define STM32F103xB
/*
* IO pins assignments.
*/
#define GPIOA_PA0 0
#define GPIOA_PA1 1
#define GPIOA_USART_TX 2
#define GPIOA_USART_RX 3
#define GPIOA_PA4 4
#define GPIOA_LED_GREEN 5
#define GPIOA_PA6 6
#define GPIOA_PA7 7
#define GPIOA_PA8 8
#define GPIOA_PA9 9
#define GPIOA_PA10 10
#define GPIOA_PA11 11
#define GPIOA_PA12 12
#define GPIOA_SWDIO 13
#define GPIOA_SWCLK 14
#define GPIOA_PA15 15
#define GPIOB_PB0 0
#define GPIOB_PB1 1
#define GPIOB_PB2 2
#define GPIOB_SWO 3
#define GPIOB_PB4 4
#define GPIOB_PB5 5
#define GPIOB_PB6 6
#define GPIOB_PB7 7
#define GPIOB_PB8 8
#define GPIOB_PB9 9
#define GPIOB_PB10 10
#define GPIOB_PB11 11
#define GPIOB_PB12 12
#define GPIOB_PB13 13
#define GPIOB_PB14 14
#define GPIOB_PB15 15
#define GPIOC_PC0 0
#define GPIOC_PC1 1
#define GPIOC_PC2 2
#define GPIOC_PC3 3
#define GPIOC_PC4 4
#define GPIOC_PC5 5
#define GPIOC_PC6 6
#define GPIOC_PC7 7
#define GPIOC_PC8 8
#define GPIOC_PC9 9
#define GPIOC_PC10 10
#define GPIOC_PC11 11
#define GPIOC_PC12 12
#define GPIOC_BUTTON 13
#define GPIOC_PC14 14
#define GPIOC_PC15 15
#define GPIOD_OSC_IN 0
#define GPIOD_OSC_OUT 1
#define GPIOD_PD2 2
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input with pull-up except:
* PA2 - Alternate output (GPIOA_USART_TX).
* PA3 - Normal input (GPIOA_USART_RX).
* PA5 - Push Pull output (GPIOA_LED_GREEN).
* PA13 - Pull-up input (GPIOA_SWDIO).
* PA14 - Pull-down input (GPIOA_SWCLK).
*/
#define VAL_GPIOACRL 0x88384B88 /* PA7...PA0 */
#define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFBFDF
/*
* Port B setup.
* Everything input with pull-up except:
* PB3 - Pull-up input (GPIOA_SWO).
*/
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup.
* Everything input with pull-up except:
* PC13 - Normal input (GPIOC_BUTTON).
*/
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x88488888 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFFFF
/*
* Port D setup.
* Everything input with pull-up except:
* PD0 - Normal input (GPIOD_OSC_IN).
* PD1 - Normal input (GPIOD_OSC_OUT).
*/
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
#define VAL_GPIODODR 0xFFFFFFFF
/*
* Port E setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
#define VAL_GPIOEODR 0xFFFFFFFF
/*
* USB bus activation macro, required by the USB driver.
*/
#define usb_lld_connect_bus(usbp)
/*
* USB bus de-activation macro, required by the USB driver.
*/
#define usb_lld_disconnect_bus(usbp)
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
