aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* layerscape: update u-boot to LSDK-18.06Yangbo Lu2018-09-221-9/+21
| | | | | | | | | | | | | | The u-boot source code had been migrated to codeaurora for LSDK-18.06 release and the future release. This patch is to update u-boot to LSDK-18.06 for both uboot-layerscape and uboot-layerscape-armv8_32b packages. Besides, this patch also introduced some other changes. - Reworked uboot-layerscape makefile to make it more readable. - Define package in uboot-layerscape-armv8_32b for each board. - Fixed u-boot package selection in target image makefile. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update ls-rcw to LSDK-18.06Yangbo Lu2018-09-221-6/+6
| | | | | | | | | | | | The rcw source code had been migrated to codeaurora for LSDK-18.06 release and the future release. The source code had also involved ls1012ardb/ls1012afrdm/ ls1088ardb/ls2088ardb rcw, so we updated ls-rcw to LSDK-18.06, reworked the makefile and dropped ls-rcw-bin package in this patch. Also reworked ls-rcw patch to adapt to the latest source code. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update fman-ucode to LSDK-18.06Yangbo Lu2018-09-221-3/+3
| | | | | | | | | Actually there was no change for fman-ucode in LSDK-18.06 just tagged with LSDK-18.06. This patch is to rework the fman-ucode makefile to make it more readable, and to use lsdk-1806 as the PKG_VERSION. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* zynq: kernel: select FPGA-related configsLuis Araneda2018-09-221-0/+10
| | | | | | These configs are necessary to program the FPGA fabric Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* sunxi: build image/uboot for the NanoPi NEO2Jasper Scholte2018-09-221-0/+10
| | | | | | | | The NanoPi NEO2 is a small Allwinner H5 based board available with different DRAM configurations. This board is very similar to the NanoPi NEO PLUS2 Signed-off-by: Jasper Scholte <NightNL@outlook.com>
* kernel: generic: Fix nftables inet table breakageBrett Mastbergen2018-09-2231-42/+1230
| | | | | | | | | | | | | | | | | | | | | | | | | | Commit b7265c59ab7d ("kernel: backport a series of netfilter cleanup patches to 4.14") added patch 302-netfilter-nf_tables_inet-don-t-use- multihook-infrast.patch. That patch switches the netfilter core in the kernel to use the new native NFPROTO_INET support. Unfortunately, the new native NFPROTO_INET support does not exist in 4.14 and was not backported along with this patchset. As such, nftables inet tables never see any traffic. As an example the following nft counter rule should increment for every packet coming into the box, but never will: nft add table inet foo nft add chain inet foo bar { type filter hook input priority 0\; } nft add rule inet foo bar counter This commit pulls in the required backport patches to add the new native NFPROTO_INET support, and thus restore nftables inet table functionality. Tested on Turris Omnia (mvebu) Fixes: b7265c59ab7d ("kernel: backport a series of netfilter cleanup ...") Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
* ath79: Fix GL-AR300M USB triggerRobert Marko2018-09-221-1/+1
| | | | | | Correct a typo preventing USB trigger to work on AR300M. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ar71xx: flag FritzBox 4020 buttons as active lowDavid Bauer2018-09-221-2/+2
| | | | | | | | | Buttons of AVM FritzBox 4020 are incorrectly flagged as active high. This was an oversight as RFKill button was working as expected even with incorrectly flagged GPIO. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: flag FritzBox 4020 buttons as active lowDavid Bauer2018-09-221-2/+2
| | | | | | | | | Buttons of AVM FritzBox 4020 are incorrectly flagged as active high. This was an oversight as RFKill button was working as expected even with incorrectly flagged GPIO. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: re-enable MIPS VDSOKevin Darbyshire-Bryant2018-09-221-23/+0
| | | | | | | | | | | | | | kernel upstream commit 9efcaa7c4afba5628f2650a76f69c798f47eeb18 to 4.14 itself a backport of 0f02cfbc3d9e413d450d8d0fd660077c23f67eff has resolved the cache line issues that led to us disabling VDSO by default on MIPS. Remove our force disable patch: pending-4.14/206-mips-disable-vdso.patch Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.71Koen Vandeputte2018-09-2115-48/+48
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.128Koen Vandeputte2018-09-211-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.70Koen Vandeputte2018-09-1711-55/+114
| | | | | | | | | | | | | | | Refreshed all patches. Added new patch: - 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch This fixes a bug introduced in upstream 4.14.68 which caused targets using ubifs to produce file-system errors on boot, rendering them useless. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.127Koen Vandeputte2018-09-176-15/+15
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: add missing symbolJohn Crispin2018-09-101-0/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: Fix early memory calculation for certain MIPS platformsTobias Wolf2018-09-101-0/+45
| | | | | | | | | Kernel upstream commit 67a3ba25aa95 ("MIPS: Fix incorrect mem=X@Y handling") introduced a new issue for rt288x where "PHYS_OFFSET" is 0x0 but the calculated "ramstart" is not. As the prerequisite of custom memory map has been removed, this results in the full memory range of 0x0 - 0x8000000 to be marked as reserved for this platform. This patch adds the originally intended prerequisite again. Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
* ath79: ubnt-xm: add rssileds packageLech Perczak2018-09-101-1/+1
| | | | | | | | In order to make RSSI indicator on the device work out of box, include "rssileds" package in per-device rootfs image by default for Ubiquiti XM family. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: create RSSI monitor on wlan0Lech Perczak2018-09-101-0/+1
| | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti XM family, the mapping for rssileds monitor was omitted by mistake. Therefore create the mapping, so RSSI LEDs work without additional configuration, after starting rssileds service. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for Buffalo WZR-HP-AG300HBernhard Frauendienst2018-09-107-27/+336
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WZR-HP-AG300H is a dual band router based on Qualcom Atheros AR7161 rev 2 Specification: - 680 MHz CPU (Qualcomm Atheros AR7161) - 128 MiB RAM (2x Samsung K4H511638G-LCCC) - 32 MiB Flash (2x Winbond 25Q128BVFG) - WiFi 5 GHz a/n (Atheros AR9220) - WiFi 2.4 GHz b/g/n (Atheros AR9223) - 1000Base-T WAN (Atheros AR7161) - 4x 1000Base-T Switch (Atheros AR8316) - 1x USB 2.0 - 3 Buttons (AOSS/WPS, Reset, USB Eject) - 2 Slide switches (Router (on/off/auto), Movie Engine (on/off)) - 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber, WLAN 5GHz green, WLAN 5GHz LED amber, Router green, Diag red, Movie Engine blue, USB green) It is already supported by the ar71xx target. For more information on the device visit the wiki: <https://openwrt.org/toh/buffalo/wzr-hp-ag300h> Serial console: - The UART Header is next to Movie Engine Switch. - Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V) - The Serial setting is 115200-8-N-1. Installation of OpenWRT from vendor firmware: - Connect to the Web-interface at http://192.168.11.1 - Go to “Administration” → “Firmware Upgrade” - Upload the OpenWrt factory image Tested: - Ethernet (LAN, WAN) - WiFi - Installation - via TFTP rescue - via factory image - on firmware v1.77 (28-05-2012) - on pro firmware v24SP2 r30356 (26-03-2018) - via sysupgrade from ar71xx (wlan devices don't work because of new names) - via sysupgrade from itself - Buttons - LEDS - USB (Power control and device recognition) Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
* kernel: add driver for virtual mtd_concat devicesBernhard Frauendienst2018-09-103-0/+372
| | | | | | | | | | | | | | | | | | | | | | | | | | Some systems require multiple flash chips to be concatenated and read as a single mtd device. The ar71xx target provides custom code to create such mtdconcat devices. When porting devices to ath79, however, there is no way to create such devices from within the device tree. This commit adds a driver for creating virtual mtd-concat devices to the ath79 target. Nodes must have a compatible = "virtual,mtd-concat" line, and define a list of devices to concat in the 'devices' property, for example: flash { compatible = "virtual,mtd-concat"; devices = <&flash0 &flash1>; }; The driver is added to the very end of the mtd Makefile to increase the likelyhood of all child devices already being loaded at the time of probing, preventing unnecessary deferred probes which might in turn cause other problems (like failure to load MAC addresses from art because the partitions are not loaded yet). Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
* ath79: add support for ELECOM WRC-300GHBK2-IINAGAKI Hiroshi2018-09-103-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 4x keys(connected to GPIO: 3x) - UART header on PCB - TX, GND, RX, Vcc from ethernet port side - 115200n8 Flash instruction using factory image: 1. Boot the WRC-300GHBK2-I normaly and connect the computer to its LAN port 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with squashfs-sysupgrade image for WRC-300GHBK2-I 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: backport i2c-gpio working over slow can_sleep GPIOsMartin Schiller2018-09-102-0/+168
| | | | Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* kernel: backport rtc ds1308 support to 4.9Martin Schiller2018-09-101-0/+51
| | | | Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* mvebu: Replace RTC initialization patch with upstreamed versionRosen Penev2018-09-103-74/+78
| | | | | | | | | While we're at it, rename the patches to their proper git format-patch name. Tested on a Turris Omnia. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ath79: add support for WD My Net Wi-Fi Range ExtenderChristian Lamparter2018-09-105-1/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch ports over support for the device from ar71xx. SOC: AR7370 (Wasp - AR9344 rev2 0001974c) RAM: Winbond W9725G6KB-25 32MiB FLASH: Winbond 25Q64FVSIG 8MiB WLAN: AR9380 Dual-Band 802.11abgn 3x3:3 INPUT: WPS, RESET button (hardware on/off toggle button) LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high) Serial: Header Next to the winbond flash chip (labeld JP1) Pinout is GND - NC - RX - TX - 3V3 (JP1) The Serial setting is 115200-8-N-1. - Installation via uboot's upgrade command 0. attach serial cable 1. interrupt uboot and enter "upgrade code.bin" into the u-boot prompt ar7240> upgrade code.bin 2. rename openwrt...sysupgrade.bin to code.bin on PC 3. run a tftp-client on the PC (shell)$ tftp 192.168.1.230 binary put code.bin 4. wait for the device to finish [...] Copy buff to Flash from 0x9f040000 length 0x79f000 Copy to Flash... write addr: 9f040000 done 5. enter "go" in the u-boot prompt ar7240> go - TFTP ramdisk image boot from the uboot prompt (tftp server defaults to serverip 192.168.1.254) => tftpboot 81000000 initramfs.bin => bootm Tested and working: - LEDs - Buttons - Ethernet - Wi-Fi - OpenWRT sysupgrade For flashing and debricking information see: <https://openwrt.org/toh/wd/rext> Users coming from ar71xx can use sysupgrade too. But I highly advise to no save the old configuration and start from a clean state. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: port cybertan_part from ar71xxChristian Lamparter2018-09-103-0/+183
| | | | | | | | | | | | | This patch ports the cybertan_part code from ar71xx and converts the driver to a DT-supported mtd parser. As a result, it will no longer add the u-boot, nvram and art partitions, which were never part of the special Cybertan header. Instead these partitions have to be specified in the DT, which has the upside of making it possible to add properties (i.e.: read-only), labels and references to these important partitions. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* zynq: rename zedboard with correct manufacturerLuis Araneda2018-09-103-9/+51
| | | | | | | | | The board is made by Avnet, so rename it accordingly as upstream has done it Also move the device to maintain alphabetic order Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: add sdcard image supportLuis Araneda2018-09-103-2/+48
| | | | | | | | | | | | | | | Implement the generation of sdcard images with ext4 or squashfs + f2fs overlay, but only enable the latter automatically Additionally, add mkf2fs and e2fsprogs to default packages to manipulate ext4 and f2fs filesystems Finally, disable the automatic generation of initramfs and rootfs.tar.gz images, as they are no longer required (they can still be selected in menuconfig) Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: enable kernel overlay and f2fs supportLuis Araneda2018-09-101-1/+6
| | | | | | | Select configs to enable build-in F2FS support and use the overlayfs provided by generic config Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* zynq: remove bootargs from kernel configLuis Araneda2018-09-101-2/+0
| | | | | | | | Use options from generic instead of target-specific, as the bootargs are now passed by the bootloader and can be device-specific Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ar71xx: fix switch probing on kernel 4.14Koen Vandeputte2018-09-071-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The bump to 4.14 changed the way mdio probes behind switches. While the board_info is added to the list, the code that actually inserted the list info into the phydev structure was missing. This resulted in non-working ethernet ports. Re-add it to fix switch probing. This mimics the exact behaviour as it was in kernel 4.9. Before: [ 1.066007] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0 [ 1.073409] Atheros AR8216/AR8236/AR8316: probe of ag71xx-mdio.0:00 failed with error -22 [ 1.102455] libphy: ag71xx_mdio: probed [ 1.737938] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Generic PHY] [ 1.747994] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 2.377642] ag71xx-mdio.1: Found an AR934X built-in switch [ 2.429938] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII After: [ 11.163357] libphy: Fixed MDIO Bus: probed [ 11.319898] libphy: ag71xx_mdio: probed [ 11.360844] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0 [ 12.447398] libphy: ag71xx_mdio: probed [ 13.077402] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316] [ 13.088989] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 13.717716] ag71xx-mdio.1: Found an AR934X built-in switch [ 13.769990] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.68Koen Vandeputte2018-09-0724-239/+162
| | | | | | | | | | | | | | | | Refreshed all patches. Remove upstream accepted: - 330-Revert-MIPS-BCM47XX-Enable-74K-Core-ExternalSync-for.patch Altered: - 303-v4.16-netfilter-nf_tables-remove-multihook-chains-and-fami.patch - 308-mips32r2_tune.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.125Koen Vandeputte2018-09-073-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 3.18 to 3.18.121Koen Vandeputte2018-09-071-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add support for TP-Link TL-MR3020 v3Carlo Nel2018-09-065-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N. This PR is based on the work of @meyergru[1], with his permission. Specification: - MediaTek MT7628N/N (575 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet Flash instruction: The only way to flash the image in TL-MR3020 v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. [1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3 Signed-off-by: Carlo Nel <carlojnel@gmail.com>
* ath79: fix unaligned access panic in ag71xx_mdio_probeMatt Merhar2018-09-061-2/+2
| | | | | | | | | | | Without "syscon" being present in an ag71xx ethernet DT node's compatible property, a panic occurs at boot during probe citing "Unhandled kernel unaligned access". With this modification, the panic no longer occurs and instead the probe simply fails, allowing the boot process to continue. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* ath79: add syscon compatible property to ar7100 ethernet nodesMatt Merhar2018-09-062-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds "syscon" to the compatible properties for the eth0/eth1 nodes in ar7100.dtsi. Without this, a kernel panic is encountered on boot with some ar7100 boards. This for some reason wasn't an issue for the WNDR3800, which uses a Realtek switch chipset, but the panic was encountered on the RouterStation Pro (using an AR8216 switch) and some other boards that haven't yet been merged. The panic message mentions an unaligned access and happens in ag71xx_mdio_probe in drivers/net/ethernet/atheros/ag71xx/ag71xx_mdio.c. Even if the unaligned access is fixed, the ag71xx_mdio probe still fails without the "syscon" property. This was already being worked around in ar7161_ubnt_routerstation-pro.dts by overriding the compatible property, so this commit removes that as well. All of the other ath79 .dtsi already have this property, so no changes are needed elsewhere. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* ramips: drop obsolete sd card driver codeMathias Kresin2018-09-062-20/+4
| | | | | | | | | | | | | | | | | The pinmux for all SoCs using this driver is now set via the pinmux. It makes this code obsolete. Some of the code targeting the mt76x8 SoCs is still required. The sd card pins share the pads with the EPHY. These pads need to be switched to digital mode if the pins are used for sd cards. The eMMC 8-bit mode has to be enabled via pinmux instead of a kernel option. The uart2 group need to be set to function "sdxc d5 d4", pwm1 to "sdxc d6" and pwm0 to "sdxc d7" to do so. It can't be done by as part of a default pinmux, as it would break the normal operation of uart2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add mt7620/1 sdhci pinmuxMathias Kresin2018-09-068-16/+13
| | | | | | | Set the pins to the required mode via the pinmux driver. It allows to get rid of the pinmux related code in the sd card driver. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix mt7620a ND/SD pins pinmuxesMathias Kresin2018-09-064-4/+4
| | | | | | | | | | Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually exclusive and for most of the boards not even used as GPIOs. If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still GPIOs (#45 and #46). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: reference node by labelMathias Kresin2018-09-061-4/+4
| | | | | | Reference the HC5661A sdhci node by label instead of by the full path. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add rt3352 SPI_CS1 pinmuxMathias Kresin2018-09-061-0/+45
| | | | | | | | The rt3352 has a pin that can be used as second spi chip select, watchdog reset or GPIO. The pinmux setup was missing the definition of said pin but it is already used in the SoC dtsi. Signed-off-by: Mathias Kresin <dev@kresin.me>
* imx6: use BUILD_DEVICES in uboot-imx6 for mx6cuboxiFelix Fietkau2018-09-051-1/+1
| | | | | | Fixes build with the default profile Signed-off-by: Felix Fietkau <nbd@nbd.name>
* imx6: rename Generic profile to Default, fixes u-boot image build issueFelix Fietkau2018-09-051-4/+4
| | | | | | | u-boot.mk checks for the Default profile to build images for all targets. This brings the target default profile in sync with other targets Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mpc85xx: add migration script for TP-Link TL-WDR4900 v1 WLAN PCI pathsMatthias Schiffer2018-09-041-0/+63
| | | | | | | | | | PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9; migrate config so existing wifi-iface definitions don't break. This is implemented as a hotplug handler rather than a uci-defaults script as the migration script must run before the 10-wifi-detect hotplug handler. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* imx6: extend cubox support to hummingboard, add support for building full imagesFelix Fietkau2018-09-033-12/+54
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* imx6: enable f2fs and loopback support in preparation for squashfs with ↵Felix Fietkau2018-09-032-1/+8
| | | | | | overlay support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: add support for enabling the rootfs/boot partition size option via ↵Felix Fietkau2018-09-031-0/+6
| | | | | | target feature Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: ethernet: unify tx descriptor buffer splittingFelix Fietkau2018-09-031-75/+83
| | | | | | | | A buffer is split into multiple descriptors if it exceeds 16 KB. Apply the same split for the skb head as well (to deal with corner cases on fraglist support) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Revert "ramips: mmc: Fix init for MT7628AN"Jo-Philipp Wich2018-08-302-16/+1
| | | | | | | | | | This reverts commit 3a8efaef00d6b7317c46fe6b7e923912d8bf3500. The change reportedly breaks UART2 on some boards. Furthermore it uses bitwise logic on an uninitialized variable and fails to explain what it is fixing exactly. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 20:42:36 +0000