aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/mt7621
Commit message (Collapse)AuthorAgeFilesLines
* ramips: mt7621: refactor set affinity scriptDENG Qingfang2020-07-111-19/+7
| | | | | | | | The current one only looks for mt76x2e and mt7603e, and does not work for 2 or more same Wi-Fi chips. Refactor the script to cover those cases. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)Bjørn Mork2020-07-083-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7621ST WiFi: MediaTek MT7603 Quantenna QT3840BC Flash: 128M NAND RAM: 64M LED: Dual colour red and green BTN: Reset WPS Eth: 4 x 10/100/1000 connected to MT7621 internal switch MT7621 RGMII port connected to Quantenna module GPIO: Power/reset of Quantenna module Quantenna module ---------------- The Quantenna QT3840BC (or QV840) is a separate SoC running another Linux installation. It is mounted on a wide mini-PCIe form factor module, but is connected to the RGMII port of the MT7621. It loads both a second uboot stage and an os image from the MT7621 using tftp. The module is configured using Quantenna specific RPC calls over IP, using 802.1q over the RGMII link to support multiple SSIDs. There is no support for using this module as a WiFi device in OpenWrt. A package with basic firmware and management tools is being prepared. Serial ports ------------ Two serial ports with headers: RRJ1 - 115200 8N1 - Connected to the Quantenna console J1 - 57600 8N1 - Connected to the MT7621 console Both share pinout with many other Zyxel/Mitrastar devices: 1 - NC (VDD) 2 - TX 3 - RX 4 - NC (no pin) 5 - GND Dual system partitions ---------------------- The vendor firmware and boot loader use a dual partition scheme storing a counter in the header of each partition. The partition with the highest number will be selected for boot. OpenWrt does not support this scheme and will always use the first OS partition. It will reset both counters to zero the first time sysupgrade is run, making sure the first partition is selected by the boot loader. Installation from vendor firmware --------------------------------- 1. Run a DHCP server. The WAP6805 is configured as a client device and does not have a default static IP address. Make a note of which address it is assigned 2. tftp the OpenWrt initramfs-kernel.bin image to this address. Wait for the WAP6805 to reboot. 3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a backup of all mtd partitions now. The last used OEM image is still present in either "Kernel" or "Kernel2" at this point, and can be restored later if you save a copy. 4. sysupgrade to the OpenWrt sysupgrade.bin image. Installation from U-Boot ------------------------ This requires serial console access 1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to your tftp server directory. Configure the server address as 192.168.0.33/24 2. Hit ESC when the message "Hit ESC key to stop autoboot" appears 3. Type "ATGU" + Enter, and then "2" immediately after pressing enter. 4. Answer Y to the question "Erase Linux in Flash then burn new one. Are you sure?", and answer the address/filename questions. Defaults: Input device IP (192.168.0.2) Input server IP (192.168.0.33) Input Linux Kernel filename ("ras.bin") 5. Wait until after you see the message "Done!" and power cycle the device. It will hang after flashing. 6. Continue with step 3 and 4 from the vendor firmware procedure. Notes on the WAP6805 U-Boot --------------------------- The bootloader has been modified with both ZyXELs zyloader and the device specific dual partition scheme. These changes appear to have broken a few things. The zyloader shell claims to support a number of ZyXEL AT commands, but not all of them work. The image selection scheme is unreliable and inconsistent. A limited U-Boot menu is available - and used by the above U-Boot install procedure. But direct booting into an uploaded image does not work, neither with ram nor with flash. Flashing works, but requires a hard reset after it is finished. Reverting to OEM firmware ------------------------- The OEM firmware can be restored by using mtd write from OpenWrt, flashing it to the "Kernel" partition. E.g. ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin OEM firmwares for the WAP6805 are not avaible for public download, so a backup of the original installation is required. See above. Alternatively, firmware for the WAP6806 (Armor X1) may be used. This is exactly the same hardware. But the branding features do obviously differ. LED controller -------------- Hardware implementation is unknown. The dual-color LED is controlled by 3 GPIOs: 4: red 7: blinking green 13: green Enabling both red and green makes the LED appear yellow. The boot loader enables hardware blinking, causing the green LED to blink slowly on power-on, until the OpenWrt boot mode starts a faster software blink. Signed-off-by: Bjørn Mork <bjorn@mork.no> [fix alphabetic sorting for image build statement] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Add support for Xiaomi Mi Router(Black,R2100)Emir Efe Kucuk2020-07-083-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many characteristics (apart from its looks and the GPIO ports) with the 6-antenna *white* "Xiaomi Redmi Router AC2100" See the visual comparison of the two routers here: https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg Specification of R2100: - CPU: MediaTek MT7621A - RAM: 128 MB DDR3 - FLASH: 128 MB ESMT NAND - WIFI: 2x2 802.11bgn (MT7603) - WIFI: 4x4 802.11ac (MT7615) - ETH: 3xLAN+1xWAN 1000base-T - LED: Power, WAN in Yellow and Blue - UART: On board (Don't know where is should be confirmed by anybody else) - Modified u-boot Hacking of official firmware process is same at both RM2100 and R2100. Thanks to @namidairo Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide Guide is written for MacOS but it will work at linux. needed packages: python3(with scapy), netcat, http server, telnet client 1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware 2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1 3. nvram set uart_en=1 4. nvram set bootdelay=5 5. nvram set flag_try_sys1_failed=1 6. nvram commit 7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0 other than these I specified in here. Everything is same with: https://github.com/openwrt/openwrt/commit/f3792690c4f0567a8965d82898295b9d50c3bb7e Thanks for all community and especially for this device: @Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com) MAC Locations: WAN *:b5 = factory 0xe006 LAN *:b6 = factory 0xe000 WIFI 5ghz *:b8 = factory 0x8004 WIFI 2.4ghz *:b7 = factory 0x0004 Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com> [refactored common image bits into Device/xiaomi-ac2100, fixed From:] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax Gemini RE23SDavide Fioravanti2020-07-081-9/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 128MB FLASH: 16MB NOR (Macronix MX25L12805D) ETH: 1x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615 (4x4:4) - 5GHz: 1x MT7615 (4x4:4) - 4 antennas: 2 external detachable and 2 internal BTN: - 1x Reset button - 1x WPS button LEDS: - 1x Green led (Power) - 1x Green-Amber-Red led (Wifi) UART: - 57600-8-N-1 Everything works correctly. Installation ------------ Flash the factory image directly from OEM web interface. (You can login using these credentials: admin/1234) Restore OEM Firmware -------------------- Flash the OEM "bin" firmware directly from LUCI. The firmware is downloadable from the OEM web page. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Restoring procedure tested with RE23_1.08.bin MAC addresses ------------- factory 0x4 *:24 factory 0x8004 *:25 Cimage 0x07 *:24 Cimage 0x0D *:24 Cimage 0x13 *:24 Cimage 0x19 *:25 No other addresses were found in factory partition. Since the label contains both the 2.4GHz and 5GHz mac address I decided to set the 5GHz one as label-mac-device. Moreover it also corresponds to the lan mac address. Notes ----- The wifi led in the OEM firmware changes colour depending on the signal strength. This can be done in OpenWrt but just for one interface. So for now will not be any default action for this led. If you want to open the case, pay attention to the antenna placed on the bottom part of the front cover. The wire is a bit short and it breaks easily. (I broke it) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [fix two typos and add extended MAC address section to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use WiFi LED DT triggers for TP-Link RE650 v1Adrian Schmutzler2020-07-071-3/+3
| | | | | | | | | | | | This moves WiFi LED triggers from 01_leds to device tree. While at it, convert the labels there to lower case; this is more commonly used and the change will actually remove competition between DT trigger and leftover uci config on already installed systems. Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE500 v1Christoph Krapp2020-07-072-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device uses the same hardware as RE650 v1 which got supported in 8c51dde. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin from the RE500 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep state_default in DTS files, fix label-mac-device, use lower case for WiFi LEDs] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for NETGEAR WAC124Jan Hoffmann2020-06-272-0/+2
| | | | | | | | | | | | | | | | | | | | | The WAC124 hardware appears to be identical to R6260/R6350/R6850. SoC: MediaTek MT7621AT RAM: 128M DDR3 FLASH: 128M NAND (Macronix MX30LF1G18AC) WiFI: MediaTek MT7603 bgn 2T2R MediaTek MT7615 nac 4T4R ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN) USB: 1x USB 2.0 BTN: Reset, WPS LED: Power, Internet, WiFi, USB (all green) Installation: The factory image can be flashed from the stock firmware web interface or using nmrpflash. With nmrpflash it is also possible to revert to stock firmware. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-162-4/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix IPv4-only corner case in 01_enable_packet_steeringAdrian Schmutzler2020-06-151-0/+1
| | | | | | | | | | | | | | | | The uci config section network.globals set up in /bin/config_generate will only be created if /proc/sys/net/ipv6 exists. Correspondingly, lacking IPv6 support, the command uci set network.globals.packet_steering=1 will fail with "uci: Invalid argument" as the network.globals config has not been set up. Fix that by adding the setup there as well. Fixes: dfd62e575c6c ("ramips: enable packet steering by default on mt7621") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: add support for NETGEAR WAC104Pawel Dembicki2020-06-122-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | NETGEAR WAC104 is an AP based on castrated R6220, without WAN port and USB. SoC: MediaTek MT7621ST RAM: 128M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7612EN an+ac MediaTek MT7603EN bgn ETH: MediaTek MT7621ST (4x LAN) BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: 7x (3x GPIO controlled) Installation: Login to netgear webinterface and flash factory.img Back to stock: Use nmrpflash to revert stock image. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: limit uci commit to the changed config fileAdrian Schmutzler2020-06-111-1/+1
| | | | | | | Since 01_enable_packet_steering only touches the network config, limit the uci commit to this as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable packet steering by default on mt7621Felix Fietkau2020-06-101-0/+4
| | | | | | | It provides a significant performance boost, especially with flow offloading enabled Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: erx and erx-sfp: fix missing WAN interfacePerry Melange2020-06-091-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses"), this change was discussed in https://github.com/openwrt/openwrt/pull/2901#discussion_r407238452 With commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses"), all the ports were put into the LAN bridge, with the argument that the OEM firmware does not have a WAN port enabled. In the default OEM setup, all of the ports except eth0 are dead and eth0 is set to a static IP address without providing DHCP services when connected. It is only after the wizard has been run that eth0 becomes the WAN port and all the rest of the ports belong to LAN with DHCP enabled. Having all of the ports set to the LAN bridge does not mirror the default OEM setup. To accomplish that, then only eth0 would be in the LAN bridge. But this is not the expected behaviour of OpenWrt. Therefore this proposal to set eth0 to WAN and eth1-N to LAN provides the expected behaviour expected from OpenWrt, maintains the current documentation as up-to-date, and does not require the user to manually detach eth0 from the LAN bridge, create the WAN(6) interface(s), and set eth0 to the WAN(6) interface(s). Fixes: 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses") Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com> [commit subject and description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix 04_led_migration case syntax for mt7621Russell Senior2020-05-231-1/+3
| | | | | | | | | | | | | Commit f761f4052c4 had bogus case syntax, the uci-defaults script threw errors as a result and exited non-zero, probably didn't do what was intended, but tried over and over since the non-zero exit prevents the script from being deleted. Fixes: f761f4052c41 ("ramips: mt7621: harmonize naming scheme for Mikrotik") Signed-off-by: Russell Senior <russell@personaltelco.net> [extend commit title, add Fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)Richard Huynh2020-05-203-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7621A - RAM: 128 MB DDR3 - FLASH: 128 MB ESMT NAND - WIFI: 2x2 802.11bgn (MT7603) - WIFI: 4x4 802.11ac (MT7615) - ETH: 3xLAN+1xWAN 1000base-T - LED: Power, WAN, in Amber and White - UART: On board near ethernet, opposite side from power - Modified u-boot Installation: 1. Run linked exploit to get shell, startup telnet and wget the files over 2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1 3. nvram set uart_en=1 4. nvram set bootdelay=5 5. nvram set flag_try_sys1_failed=1 6. nvram commit 7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0 Restore to stock: 1. Setup PXE and TFTP server serving stock firmware image (See dhcp-boot option of dnsmasq) 2. Hold reset button down before powering on and wait for flashing amber led 3. Release reset button 4. Wait until status led changes from flashing amber to white Notes: This device has dual kernel and rootfs slots like other Xiaomi devices currently supported (mir3g, etc.) thus, we use the second slot and overwrite the first rootfs onwards in order to get more space. Exploit and detailed instructions: https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100 An implementation of CVE-2020-8597 against stock firmware version 1.0.14 This requires a computer with ethernet plugged into the wan port and an active PPPoE session, and if successful will open a reverse shell to 192.168.31.177 on port 31337. As this shell is somewhat unreliable and likely to be killed in a random amount of time, it is recommended to wget a static compiled busybox binary onto the device and start telnetd with it. The stock telnetd and dropbear unfortunately appear inoperable. (Disabled on release versions of stock firmware likely) Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox chmod a+x /tmp/busybox /tmp/busybox telnetd -l /bin/sh Tested-by: David Martinez <bonkilla@gmail.com> Signed-off-by: Richard Huynh <voxlympha@gmail.com>
* ramips: add support for Linksys EA7500 v2Davide Fioravanti2020-05-175-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys EA7500 v2 is advertised as AC1900, but its internal hardware is AC2600 capable. Hardware -------- SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads) RAM: 256M (Nanya NT5CC128M16IP-DI) FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI) ETH: 5x 10/100/1000 Mbps Ethernet (MT7530) WIFI: - 2.4GHz: 1x MT7615N (4x4:4) - 5GHz: 1x MT7615N (4x4:4) - 4 antennas: 3 external detachable antennas and 1 internal USB: - 1x USB 3.0 - 1x USB 2.0 BTN: - 1x Reset button - 1x WPS button LEDS: - 1x White led (Power) - 6x Green leds (link lan1-lan4, link wan, wps) - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable) Everything works correctly. Installation ------------ The “factory” openwrt image can be flashed directly from OEM stock firmware. After the flash the router will reboot automatically. However, due to the dual boot system, the first installation could fail (if you want to know why, read the footnotes). If the flash succeed and you can reach OpenWrt through the web interface or ssh, you are done. Otherwise the router will try to boot 3 times and then will automatically boot the OEM firmware (don’t turn off the router. Simply wait and try to reach the router through the web interface every now and then, it will take few minutes). After this, you should be back in the OEM firmware. Now you have to flash the OEM Firmware over itself using the OEM web interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img downloaded from the Linksys website). When the router reboots flash the “factory” OpenWrt image and this time it should work. After the OpenWrt installation you have to use the sysupgrade image for future updates. Restore OEM Firmware -------------------- After the OpenWrt flash, the OEM firmware is still stored in the second partition thanks to the dual boot system. You can switch from OpenWrt to OEM firmware and vice-versa failing the boot 3 times in a row: 1) power on the router 2) wait 15 seconds 3) power off the router 4) repeat steps 1-2-3 twice more. 5) power on the router and you should be in the “other” firmware If you want to completely remove OpenWrt from your router, switch to the OEM firmware and then flash OEM firmware from the web interface as a normal update. This procedure will overwrite the OpenWrt partition. Footnotes --------- The Linksys EA7500-v2 has a dual boot system to avoid bricks. This system works using 2 pair of partitions: 1) "kernel" and "rootfs" 2) "alt_kernel" and "alt_rootfs". After 3 failed boot attempts, the bootloader tries to boot the other pair of partitions and so on. This system is managed by the bootloader, which writes a bootcount in the s_env partition, and if successfully booted, the system add a "zero-bootcount" after the previous value. A system update performed from OEM firmware, writes the firmware on the other pair of partitions and sets the bootloader to boot the new pair of partitions editing the “boot_part” variable in the bootloader vars. Effectively it's a quick and safe system to switch the selected boot partition. Another way to switch the boot partition is: 1) power on the router 2) wait 15 seconds 3) power off the router 4) repeat steps 1-2-3 twice more. 5) power on the router and you should be in the “other” firmware In this OpenWrt port, this dual boot system is partially working because the bootloader sets the right rootfs partition in the cmdline but unfortunately OpenWrt for ramips platform overwrites the cmdline so is not possible to detect the right rootfs partition. Because all of this, I preferred to simply use the first pair of partitions and set read-only the other pair. However this solution is not optimal because is not possible to know without opening the case which is the current booted partition. Let’s take for example a router booting the OEM firmware from the first pair of partitions. If we flash the OpenWrt image, it will be written on the second pair. In this situation the router will bootloop 3 times and then will automatically come back to the first pair of partitions containg the OEM firmware. In this situation, to flash OpenWrt correctly is necessary to switch the booting partition, flashing again the OEM firmware over itself. At this point the OEM firmware is on both pair of partitions but the current booted pair is the second one. Now, flashing the OpenWrt factory image will write the firmware on the first pair and then will boot correctly. If this limitation in the ramips platform about the cmdline will be fixed, the dual boot system can also be implemented in OpenWrt with almost no effort. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Co-Developed-by: Jackson Lim <jackcolentern@gmail.com> Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
* ramips/mt7621: mikrotik: don't use mtd-mac-address in DTSThibaut VARÈNE2020-05-081-1/+4
| | | | | | | | | | | | | As evidenced here[1] the device MAC address can be stored at a random offset in the hard_config partition. Rely on sysfs to update the MAC address correctly. Adjust config so that WAN is base MAC and LAN is base MAC +1 to better match label and vendor OS. [1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021 Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips/mt7621: enable mikrotik platform driverThibaut VARÈNE2020-05-081-0/+2
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips/mt7621: enable CONFIG_MTD_ROUTERBOOT_PARTSThibaut VARÈNE2020-05-081-0/+1
| | | | Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ramips: fix MikroTik 750Gr3 ports MAC addressesDENG Qingfang2020-04-281-1/+0
| | | | | | | | | | | | | | | According to a user in OpenWrt forum, on RouterOS the MAC addresses are ether1(WAN) = MAC ether2(LAN2) = MAC+1 ether3(LAN3) = MAC+2 etc. Fix the MAC addresses in OpenWrt. Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [remove label_mac in 02_network] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable SFP port for Ubiquiti ER-X-SFPRené van Dorst2020-04-252-2/+5
| | | | | | | | | | | | | | | SFP cage of this device is connected via a AT8031 phy to port 5 of the switch. This phy act as a RGMII-to-SerDes converter. Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus. SFP cage also has module detect pin which is connected to I2C gpio expander. With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port. NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding! This means that some SGMII modules can work and only at forced 1GBit/full-duplex! Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: remove config-4.14 for mt7621/mt76x8Adrian Schmutzler2020-04-231-316/+0
| | | | | | | | | | | mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their DTS(I) files are incompatible to kernel 4.14. Remove the corresponding kernel config files to signal that more boldly and to prevent accidentally patching the wrong kernel when pulling in older config patches. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: Ubiquiti ER-X-SFP: fix gpio numbers for POE enable gpiosRené van Dorst2020-04-181-5/+5
| | | | | | | With v5.4 kernel a new gpio driver is used. GPIO numbering has changed so update 03_gpio_switches too. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: mt7621: Ubiquiti ER-X: fix gpio number for POE enable gpioRené van Dorst2020-04-181-1/+1
| | | | | | | With v5.4 kernel a new gpio driver is used. GPIO numbering has changed so update 03_gpio_switches too. Signed-off-by: René van Dorst <opensource@vdorst.com>
* ramips: use all reserved space for HiWiFi HC5962DENG Qingfang2020-04-181-0/+1
| | | | | | | | These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt" do not contain any device-specific data and can be used for /overlay, resulting in 121M space Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: move and rename out-of-tree mtk eth driverChuanhong Guo2020-04-121-0/+1
| | | | | | | move the driver into shared 'files' directory and rename all symbols from mediatek/mtk to ralink. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: tidy up names for Ubiquiti devicesAdrian Schmutzler2020-04-124-8/+8
| | | | | | | | | | | | | | | The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in all targets except ramips and also recommended by the kernel. This patch adjusts the various board/image/device name variables accordingly. Since we touch it anyway, this also adds the space in "EdgeRouter X" as a hyphen to those variables to really make them consistent with the model name. While at it, create a real shared definition for the devices in image/mt7621.mk instead of deriving one device from another. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WN-AX2033GRYanase Yuki2020-04-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX2033GR is roughly the same as I-O DATA WN-AX1167GR2. The difference is Wi-Fi feature. Specification ============= - SoC: MediaTek MT7621A - RAM: DDR3 128 MiB - Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100) - Wi-Fi: MediaTek MT7603E - Wi-Fi: MediaTek MT7615 - Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN) - LED: 2x green LED - Input: 2x tactile switch, 1x slide switch - Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND) - Power: DC 12V This device only supports channel 1-13 and 36-140. Thus, narrower frequency limits compared to other devices are required for limiting wi-fi frequency correctly. Without this, non-supported frequencies are activated. Flash instructions ================== 1. Open the router management page (192.168.0.1). 2. Update router firmware using "initramfs-kernel.bin". 3. After updating, run sysupgrade with "sysupgrade.bin". Recovery instructions ===================== WN-AX2033GR contains Zyxel Z-LOADER 1. Setup TFTP server (IP address: 10.10.10.3). 2. Put official firmware into TFTP server directory (distribution site: https://www.iodata.jp/lib/software/w/2068.htm) 3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server. 4. Connect to serial console. 5. Interrupt booting by Esc key. 6. Flash firmware using "ATNR 1,[firmware filename]" command. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [adjust for kernel 5.4, add recovery instructions/frequency comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: harmonize naming scheme for MikrotikAdrian Schmutzler2020-04-085-12/+20
| | | | | | | | | | | | | | | | | So far, image/device/board names for Mikrotik devices in mt7621 have been used quite inconsistently. This patch harmonizes the naming scheme by applying the same style as used lately in ath79, i.e. using "RouterBOARD" as separate word in the model name (instead of RB prefix for the number) and deriving the board/device name from that (= make lower case and replace spaces by hyphens). This style has already been used for most the model/DEVICE_MODEL variables in mt7621, so this is essentially just adjusting the remaining variables to that. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: add label mac address to rbm11gTobias Schramm2020-04-081-0/+1
| | | | | | | The rbm11g has a label with printed on mac address similar to the rbm33g. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
* ramips: mt7621: bringup dsa master on preinitChuanhong Guo2020-04-041-0/+22
| | | | | | | | DSA requires master netdev to be up before any of its slave ports. Bring it up during preinit so that the first lan port can be used on failsafe. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: add new NAND driverDENG Qingfang2020-04-041-0/+1
| | | | | | Add new NAND driver for MT7621 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix MikroTik 750Gr3 LAN ports namesDENG Qingfang2020-04-041-0/+3
| | | | | | They are labeled as LAN2..LAN5 instead of LAN1..LAN4 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addressesDENG Qingfang2020-04-041-0/+4
| | | | | | | | | | | | | | | | | The name of each user port should be eth0..4, instead of lan1..4 and there is no WAN port. Rename them to match the official firmware. To avoid conflict with the master port (gmac0), rename it to "dsa". The official firmware assigns MAC address in this way: eth0 = label mac eth1 = label mac + 1 ... eth4 = label mac + 4 Since we have switched to DSA, it's possible to use different MAC for each port. Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: switch kernel version to 5.4DENG Qingfang2020-04-041-0/+2
| | | | | | | After all dts and config changes, 4.14 no longer works on mt7621. Switch it to 5.4 directly. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: change default ramips_setup_interfaces configurationDENG Qingfang2020-04-041-63/+1
| | | | | | | Most of MT7621 boards have LAN1~4 and WAN, so make this as the default Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: mt7621: update dts/defconfig for DSADENG Qingfang2020-04-042-214/+68
| | | | | | | | | | | update dts and network/LED configuration for DSA driver. sysupgrade from images prior to this commit with config preserved will cause broken ethernet setup. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Acked-by: Jo-Philipp Wich <jo@mein.io> [split commit] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: refresh kernel configDENG Qingfang2020-04-041-52/+68
| | | | Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: copy patches and kernel config to 5.4DENG Qingfang2020-04-041-0/+315
| | | | | | Copy patches and kernel config to 5.4 for ramips Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for Ubiquiti UniFi nanoHDDavid Bauer2020-03-101-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7621AT WiFi: MediaTek MT7603 bgn 2T2R MediaTek MT7615 ac 4T4R Flash: 32M SPI (Macronix MX25L25635F) RAM: 128M DDR3 (Winbond W631GG6KB) LED: Dome (Blue / White) BTN: Reset Installation ------------ These instructions were written for firmware version v3.9.27. Downgrade if necessary. 1. Copy the OpenWrt sysupgrade image to the devices /tmp folder via scp. On factory defaults, user and password is "ubnt" at 192.168.1.20/24. 2. Write the bootselect flag. Otherwise, the device might boot from the wrong partition. Verify the mtd partition used in the command below is the one labled "bs" in /proc/mtd (as this might change in the future). > dd if=/dev/zero bs=1 count=1 of=/dev/mtd4 3. Write the OpenWrt sysupgrade to the mtd partitions labled "kernel0" and "kernel1". > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6 > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7 4. Reboot or powercycle the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for NETGEAR R6700v2/AC2400Adrian Schmutzler2020-03-043-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Installation: Login to netgear webinterface and flash factory.img Based on a discontinued GitHub Pull Request by kuyokushin <codenamezero@protonmail.com> https://github.com/openwrt/openwrt/pull/2545 NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk AC2400, Nighthawk AC2100 and already added R6800. Rest of them should be really easy supportable. Image for R6700v2 should work perfectly with them. Please refer: https://github.com/openwrt/openwrt/pull/2614 Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2] Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [add guest led to mt7621_netgear_r6700-v2.dts end edit commit message] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: add support for Netgear R6800Pawel Dembicki2020-03-044-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: fix device name of netis WF-2881 to WF2881Sungbo Eo2020-02-072-3/+3
| | | | | | | | | | | The correct model name of WF-2881 is WF2881 without hyphen. The former used boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the sysupgrade-tar image, which is newly added in the previous commit, should not be used to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: use nand_do_upgrade for netis WF-2881Sungbo Eo2020-02-071-0/+1
| | | | | | | | | | WF-2881 sysupgrade image uses UBI rootfs, but still relies on default_do_upgrade. Because of this, config backup is not restored after sysupgrade. It can be fixed by switching to nand_do_upgrade and sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar properly, so one should use factory image to upgrade from older version. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-AX1167GR2INAGAKI Hiroshi2020-02-052-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-AX1167GR2 normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for I-O DATA WN-DX1167RINAGAKI Hiroshi2020-02-053-4/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix HiWiFi HC5962 switch configurationDENG Qingfang2020-01-161-1/+4
| | | | | | HC5962 has only 3 LAN ports, switch port 0 is unused Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add label MAC address for Xiaomi MIR3GAdrian Schmutzler2020-01-081-5/+3
| | | | | | | | | | | | | | | | | | | | | | | The device label shows the address currently assigned to the OpenWrt LAN interface. Current setup is: LAN *:b8 factory 0xe006 label WAN *:b7 factory 0xe000 For vendor FW bootlog we get (manually removed parts of the address): [ 7.520000] set LAN/WAN LWLLL [ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031 [ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7 [ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031 [ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8 [ 7.540000] eth1: ===> VirtualIF_open Without further information, this does not allow verification of the currently unexpected LAN/WAN assignment (we would expect 0xe000 to be LAN). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A8004TYong-hyu Ban2020-01-051-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 256M - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615E - 5GHz: MT7615E - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1 * USB3.0 port - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 - Other info: - J9: Unknown unpopulated header. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe> [do not enable xhci node in DTS which is already enabled in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Edimax RA21SMaksym Medvedev2020-01-041-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Edimax RA21S is a dual band 11ac router, based on MediaTek MT7621A and MT7615N chips. Specification: - SoC: MediaTek MT7621A dual-core @ 880MHz - RAM: 256M (Nanya NT5CC128M16IP) - FLASH: 16MB (Macronix MX25L12835F) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) - USB: No - BTN: Reset, WPS - LED: 4 red LEDs, indistinguishable when case closed - UART: through-hole on PCB. J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad Installation: Update the factory image via the OEM web-interface (by default: http://192.168.2.1/) User: admin Password: 1234 The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect via ethernet port 2. Tested on device by @UAb5eSMn Signed-off-by: Maksym Medvedev <redrathnure@gmail.com> [split DTS and take over improvements from RG21S, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 15:39:15 +0000