aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mvebu/image/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: move definition of factory.img out of Device/DefaultAdrian Schmutzler2020-06-281-1/+0
| | | | | | | | | | The Device/Default definition in mvebu defines an IMAGE/factory.img which is not included in IMAGES, and only used twice in the individual definitions. Move it out of the default definition to keep it closer to the reassignment of IMAGES and make it more consistent with respect to other values of IMAGE/factory.img Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: simplify inclusion of subtarget image filesAdrian Schmutzler2020-06-111-11/+1
| | | | | | | | | | | | | | Many target use a repetitive if-include scheme for their subtarget image files, though their names are consistent with the subtarget names. This patch removes these redundant conditions and just uses the variable for the include where the target setup allows it. For sunxi, this includes a trivial rename of the subtarget image Makefiles. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: add support for Buffalo LinkStation LS421DEDaniel González Cabanelas2020-04-131-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370 Hardware: SoC: Marvell Armada 88F6707-A1 CPU: Cortex-A9 1200 MHz, 1 core Flash: SPI-NOR 1 MiB, NAND 512 MiB RAM: DDR3 512 MiB Ethernet: 1x 10/100/1000 Mbps USB: 1x 2.0, 1x 3.0 SATA: 2x 3.0 Gbps LEDs/Input : 5x / 2x (1x button, 1x slide-switch) RTC: Ricoh RS5C372A, I2C, no battery Flash instruction (UART+TFTP): 1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13) 2. Remove any hard drive from inside the bays. 3. Boot the Openwrt initramfs image using the U-Boot serial console: tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin bootm 0x1200000 4. Flash the sysupgrade image using the Openwrt console: sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin 5. Wait until it finish, the device will reboot with Openwrt installed on the NAND flash. Note: - Device shuting down doesn't work, even if the power slide switch is used. We must first, via MDIO, set the unused LED2 at the ethernet phy0 to off state. Reboot works ok. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-1/+1
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: rework uDPU-firmware recipeTomasz Maciej Nowak2020-03-011-3/+9
| | | | | | | | | Tar has ability to change current dir, so use that instead additional command invocation. Also being here, change tar arguments to make final archive reproducible. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: keep global DTS_DIR intactTomasz Maciej Nowak2020-03-011-1/+2
| | | | | | | | Don't rewrite global DTS_DIR, instead, use proper variable for specifying devices dts directory. For consistency, also specify the variable in default profile, as suggested by Adrian Schmutzler. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: align subtargets makefile namesTomasz Maciej Nowak2020-02-011-3/+3
| | | | | | | Align subtargets makefiles names to actual subtargets. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: use SOC to derive DEVICE_DTSAdrian Schmutzler2020-01-211-0/+1
| | | | | | | | | | | | This introduces the SOC variable to mvebu target to derive some of the DEVICE_DTS variables based on the SOC prefix and the device definition name. Since DTS names and compatible are inconsistent also in the kernel for this target, the scheme cannot be applied to all devices, though. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: move subtarget image Makefile switch to parent MakefileAdrian Schmutzler2020-01-211-0/+8
| | | | | | | | | | This moves the if conditions for choosing which image Makefiles are used to the parent image/Makefile. It seems more convenient to have "codeflow" in the parent while the subtarget-specific files only contain the definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86,tegra,mvebu: image: use common reproducible IMG_PART_SIGNATUREPaul Spooren2019-11-111-5/+3
| | | | | | | | | | | | | These targets are currently using more or less same SIGNATURE variable which provides unique partition ID/signature, so it makes sense to refactor it out into common IMG_PART_SIGNATURE variable which could be reused by all targets. This is another step in the direction of reproducible OpenWrt images. Signed-off-by: Paul Spooren <mail@aparcar.org> [split into separate commit, renamed to IMG_PART_SIGNATURE] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* build: label kernel and rootfs ext4 volumesYousong Zhou2019-11-031-1/+1
| | | | | | | | | | | UUID of ext4 volumes generated by make_ext4fs are determined by volume label and it will all be 57f8f4bc-abf4-655f-bf67-946fc0f9f25b when label is empty Labeling them does not make them unique but tools like block command from fstools have a better chance differentiating them Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* mvebu: uDPU: add sysupgrade supportVladimir Vid2019-08-241-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds sysupgrade, uboot-env and networking support for Methode uDPU device. Device features 4 partitions: ----------------------------------------- | boot | recovery | rootfs | misc | | (ext4) | (ext4) | (fsf2) | (f2fs) | _________________________________________ Idea was to use f2fs only but the u-boot currently lacks support so first 2 partition are ext4 to be u-boot readable, and this was a reason why custom build and sysupgrade sections were required. On the sysupgrade, boot and rootfs partitions are updated, firmare image and user configuration is saved on the misc partition and if the upgrade was successfull, recovery partition will be updated on after the reboot from preinit script. If the sysupgrade fails for any reason, device will fallback to recovery initramfs image. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* mvebu: use device-tree board detectionTomasz Maciej Nowak2019-05-111-1/+1
| | | | | | | | Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: align device names to vendor_device formatTomasz Maciej Nowak2019-05-111-1/+0
| | | | | | | | | | Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: don't create unnecessarily shell variablesTomasz Maciej Nowak2019-05-111-12/+6
| | | | | | | Use make syntax to pass the U-Boot image location and boot with root partitions size, instead of relying on shell functions and variables. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: improve readability of device recipesTomasz Maciej Nowak2019-05-111-16/+5
| | | | | | | | Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: introduce BOOT_SCRIPT variableTomasz Maciej Nowak2019-05-111-3/+7
| | | | | | | | | | | | All of U-Boot scripts repeat the same pattern with only Device Tree blob name changing for respective device. Therefore create generic scripts which will be altered on demad by image build process, and create BOOT_SCRIPT variable which can be added to device recipe and will allow referencing the same script by many device recipes. This will allow to slim down the ammount of files in buildroot tree and avoid needlessly incrementing amount of boot scripts if new devices will be added. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: stack repeated variablesTomasz Maciej Nowak2019-05-111-0/+8
| | | | | | | All of arm64 devices have part of variables repeatedly defined. Stack them to common define, and reference it in each device recipe. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: remove unnecessary code building dtbsTomasz Maciej Nowak2019-05-111-7/+3
| | | | | | | | | Even if dts is not included in upstream Makefile, it is built anyway by recipe specified in include/image.mk. Also remove Build/dtb, it's not used since 3f72f3a ("mvebu: clearfog: include DTB for all variants in image"). Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: make bootfs size for sdcard image configurableTomasz Maciej Nowak2019-04-061-10/+6
| | | | | | | Let's take this oportunity to implement boot-part and rootfs-part feature flags. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: add support for MACCHIATObin (cortex-a72)Damir Samardzic2018-03-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for Marvell MACCHIATObin, cortex-a72 based Marvell ARMADA 8040 Community board. Comes in two forms: Single Shot and Double Shot. Specifications: - Quad core Cortex-A72 (up to 2GHz) - DDR4 DIMM slot with optional ECC and single/dual chip select support - Dual 10GbE (1/2.5/10GbE) via copper or SFP 2.5GbE (1/2.5GbE) via SFP 1GbE via copper - SPI Flash - 3 X SATA 3.0 connectors - MicroSD connector - eMMC - PCI x4 3.0 slot - USB 2.0 Headers (Internal) - USB 3.0 connector - Console port (UART) over microUSB connector - 20-pin Connector for CPU JTAG debugger - 2 X UART Headers - 12V input via DC Jack - ATX type power connector - Form Factor: Mini-ITX (170 mm x 170 mm) More details at http://macchiatobin.net Booting from micro SD card: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually: setenv fdt_name armada-8040-mcbin.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* mvebu: unset uboot build by defaultMathias Kresin2018-03-151-0/+2
| | | | | | | | Initialise the UBOOT variable by default. Otherwise it will be unintended inherit to following images if set and causes an uboot build where not required. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: new subtarget cortex A53Tomasz Maciej Nowak2018-03-101-2/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit introduces new subtarget for Marvell EBU Armada Cortex A53 processor based devices. The first device is Globalscale ESPRESSObin. Some hardware specs: SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53 processor up to 1.2GHz RAM: 512MB, 1GB or 2GB DDR3 Storage: SATA interface µSD card slot with footprint for an optional 4GB EMMC 4MB SPI NOR flash for bootloader Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports Connectors: USB 3.0 USB 2.0 µUSB port connected to PL2303SA (USB to serial bridge controller) for UART access Expansion: 2x 46-pin GPIO headers for accessories and shields with I2C, GPIOs, PWM, UART, SPI, MMC, etc MiniPCIe slot Misc: Reset button, JTAG interface Currently booting only from µSD card is supported. The boards depending on date of dispatch can come with various U-Boot versions. For the newest version 2017.03-armada-17.10 no manual intervention should be needed to boot OpenWrt image. For the older ones it's necessary to modify default U-Boot environment: 1. Interrupt boot process to run U-Boot command line, 2. Run following commands: (for version 2017.03-armada-17.06 and 2017.03-armada-17.08) setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000" saveenv (for version 2015.01-armada-17.02 and 2015.01-armada-17.04) setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait" setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}" saveenv 3. Poweroff, insert SD card with OpenWrt image, boot and enjoy. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: Add subtarget for Cortex A9 buildHauke Mehrtens2018-03-101-153/+1
| | | | | | This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add support for Turris OmniaRyan Mounce2018-03-101-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Turris Omnia and builds an eMMC sysupgrade image in the same format as the SolidRun ClearFog. An initramfs image in the simple yet Omnia-specific 'medkit' image format is also built in order to ease the initial flashing process. Notable hardware support omissions are support for switching between SFP cage and copper PHY, and RGB LED control. Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used. Specifications: - Marvell Armada 385 1.6GHz dual-core ARMv7 CPU - 1GB DDR3 RAM - 8GB eMMC Flash - 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports) - 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN - 2x USB 3.0 - 12x dimmable RGB LEDs controlled by independent MCU - 3x Mini PCIe slots - Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz) - Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz) - Optional Quectel EC20 Mini PCIe LTE modem Flash instructions: If the U-Boot environment has been modified previously (likely manually via serial console), first use serial to reset the default environment. => env default -a => saveenv Method 1 - USB 'medkit' image w/o serial - Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS. Note that the medkit MUST be named omnia-medkit*.tar.gz - Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. - Power on the Omnia and hold down the rear reset button until 4 LEDs are illuminated, then release. - Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times. - Connect a computer to a LAN port of the Turris Omnia with a DHCP client - (if necessary) ssh-keygen -R 192.168.1.1 - ssh root@192.168.1.1 $ mount /dev/sda1 /mnt $ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive. Method 2 - TFTP w/ serial - Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy dtb + zImage to your TFTP server (rename if desired) - Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server - Connect serial console and interrupt U-Boot => dhcp => setenv serverip <tftp_server_ip_here> => tftpboot 0x01000000 zImage => tftpboot 0x02000000 dtb => bootz 0x01000000 - 0x02000000 - OpenWrt will now boot from ramdisk - Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/ $ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: unify boot.scr creationTomasz Maciej Nowak2018-03-021-11/+6
| | | | | | | Unify boot.scr generation so Makefile for device image generation won't grow without a reason. Also make boot-scr step optional. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: make sdcard bootloader option configurableTomasz Maciej Nowak2018-03-021-1/+4
| | | | | | | Remove the necessity for boot loader from SD card image creation process and make it configurable. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: fix partition type and signature for sdcardTomasz Maciej Nowak2018-03-021-1/+4
| | | | | | | | | | | Previously the partition signature was assigned from provided type. Now both are corrected wherein signature is always generated from SOURCE_DATE_EPOCH. With that the root file system can be identified by PARTUUID string, without relying on static declaration of device node. This commit also does some cosmetics, removing trailing whitespace and replacing spaces with tab. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: remove redefinition of image name for clearfogTomasz Maciej Nowak2018-03-021-2/+0
| | | | | | | | The IMAGE_NAME redefinition causes overwriting of generated SD card image when multiple root file system types are selected. In result only single SD card image is generated. This commit fixes this behaviour. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mwlwifi: add and use individual firmware packagesJohnny S. Lee2018-02-261-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | As each mvebu device only uses one of the firmwares provided by mwlwifi package, it makes sense to put them in separate packages and only install the one that is needed. Current mwlwifi version's firmware sizes and usages by devices: 88W8864.bin 118776 caiman, mamba, cobra, shelby 88W8897.bin 489932 (none) 88W8964.bin 449420 rango Changes by this commit: * indicate in title that mwlwifi also is driver for 88W8897 and 88W8964 * remove mwlwifi package's firmware installation rules * add 3 new individual firmware packages (all depends on kmod-mwlwifi): - mwlwifi-firmware-88w8864 - mwlwifi-firmware-88w8897 - mwlwifi-firmware-88w8964 * add firmware package to mvebu devices' DEVICE_PACKAGES accordingly Signed-off-by: Johnny S. Lee <_@jsl.io> [Add the used FW files to the PACKAGES of default image] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: fix sysupgrade from 17.04 for clearfog proJonas Gorski2018-02-111-0/+1
| | | | | | | | | When clearfog was renamed to clearfog pro, it broke sysupgrade from 17.04 as the new images now get rejected as incompatible. Fix this by adding the legacy boardname to the compatible devices. Fixes: ec4a8c6dee81 ("mvebu: ClearFog renamed upstream to ClearFog Pro") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-5/+19
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: clean up ClearFog Base package selectionRyan Mounce2017-10-151-6/+2
| | | | | | | | | | It is unclear why so many packages are selected for ClearFog Base compared to its big brother, and there is no reason to not append metadata for Base. Tidy this up as the only hardware difference between Base/Pro is the presence of a switch and a different board name / device tree. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: WRT3200ACM: add bluetooth moduleHenryk Heisig2017-09-171-1/+1
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* mvebu: clearfog: include DTB for all variants in imageJosua Mayer2017-05-301-3/+5
| | | | | | | Installing all armada-388-clearfog-* DTBs in the same sdcard image, it now becomes much easier to swap sdcards between different device variants. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* mvebu: add ClearFog Base supportMarko Ratkaj2017-05-141-0/+20
| | | | | | | | | | Add support for SolidRun ClearFog Base board. The base model is a smaller version of ClearFog Pro without the DSA switch, replacing it with a second copper gigabit port, and only one PCIe socket. Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: ClearFog renamed upstream to ClearFog ProMarko Ratkaj2017-05-141-6/+6
| | | | | | The conventional model is now known as the "Clearfog Pro" Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: wrt3200acm enable SDIO interfaceHenryk Heisig2017-03-111-0/+1
| | | | | | add mwifiex-sdio package to wrt3200acm Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* mvebu: append metadata to clearfog sd card imagesJonas Gorski2017-02-131-1/+1
| | | | | | | | | | | | | | Fixes the following issue: root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz Saving metaconfig... Image metadata not found Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware Image check 'fwtool_check_image' failed. root@LEDE:/# Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mvebu: put u-boot images into image staging directoryJo-Philipp Wich2017-01-271-1/+1
| | | | | | | | | | | | Do not put the u-boot images into the kernel build directory as this directory might get removed after kernel updates while the u-boot packages InstallDev recipe is not getting re-executed because it is still considered current, leading to image build failures later on due to missing u-boot images. To ensure that built bootloader images persist over kernel version updates in the buildroot, put them into the new STAGING_DIR_IMAGE directory. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* uboot-mvebu: switch to u-boot.mkFelix Fietkau2017-01-241-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: remove the clearfog-bundleFelix Fietkau2017-01-131-13/+1
| | | | | | It is obsoleted by proper SD card image support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: fix image validation errorMathias Kresin2016-12-041-2/+2
| | | | | | | | The name from the Device define will be used in the metadata. Due to typo/different spelling, this name might not match the one exported in /lib/mvebu.sh. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: fix typo in image metadata supportMathias Kresin2016-11-271-2/+2
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: use image metadata for firmware validationFelix Fietkau2016-11-241-1/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add support for the Linksys WRT3200ACM (Rango)Imre Kaloz2016-10-241-1/+9
| | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: add sysupgrade support for clearfogJonas Gorski2016-09-261-1/+1
| | | | | | | | Add and enable sysupgrade support for clearfog boards, based on how the brcm2708 target does it. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add switch node to clearfogJonas Gorski2016-09-261-1/+1
| | | | | | | | Add a switch node to clearfog to probe and initialize it on Clearfog Pro. This make the switch work and allows using all six switch ports. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* uboot-mvebu: make hidden and be m for clearfog to fix IB failing to add itJonas Gorski2016-09-261-1/+1
| | | | | | | | | | | | | Uboot-mvebu isn't a real package, which will break the image builder when it tries to install it during the packing step. Instead of cleafog selecting it through its default packages, make it default to m if the clearfog profile is selected. This will ensure it is always build, but never added to the rootfs. This fixes creating images for clearfog with IB. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* uboot-mvebu: also install into KDIR to ensure it packaged in IBJonas Gorski2016-09-261-1/+1
| | | | | | | | The clearfog image requires u-boot, so package it into KDIR to make sure it is available in imageBuilder. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-10 02:28:13 +0000