aboutsummaryrefslogtreecommitdiffstats
path: root/package
Commit message (Collapse)AuthorAgeFilesLines
* hostapd: add support for enabling HE on channel switchFelix Fietkau2021-07-121-0/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: make it possible to update station airtime weights via ubusFelix Fietkau2021-07-122-0/+99
| | | | | | This allows dynamic tuning based on other runtime information Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uboot-mediatek: several fixes for MT7622Daniel Golle2021-07-114-94/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | * ! Behavior change ! Old behavior: If the Reset button is held down during power-on do factory reset and try booting recovery from TFTP forever. If valid recovery is received via TFTP, write it to flash and boot. New behavior: If the Reset button is held down during power-on do factory reset, then try TFTP *once*, then try booting on-flash recovery, then keep trying via TFTP forever until a valid image is received. Only if there is no bootable recovery stored on flash, store the downloaded recovery. Then boot it. * Set loadaddr to 0x48000000 in order to allow booting images larger than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to 0x48000000 gives us 384MB on devices with 512MB RAM, which should be more than enough as a maximum size for uImage.FIT to be loaded. * Widely unify device-specific default environment in preparation to auto-generate it from parameters. * backport upstream commit fixing MBR/DOS partitioning Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Linksys EA8100 v2Tee Hao Wei2021-07-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
* iwinfo: update to latest Git HEAD and move device info into -data packageJo-Philipp Wich2021-07-111-7/+17
| | | | | | | | | | a0a0e02 iwinfo: rename hardware.txt to devices.txt Also split common devices.txt (former hardware.txt) into a common libiwinfo-data package to allow different libiwinfo versions to coexist without file clashes. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* procd: update to git HEADDaniel Golle2021-07-101-3/+3
| | | | | | 2dcefbd jail: add support for cgroup devices as in OCI run-time spec Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lua: make it easier to detect host-built LuaDaniel Golle2021-07-101-2/+6
| | | | | | Install pkg-config file also for host-build, clean up Lua symlinks. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* hostapd: add HE flag to get_clientsDavid Bauer2021-07-061-0/+1
| | | | | | Expose the hostapd HE flag via ubus to indicate HE capable devices. Signed-off-by: David Bauer <mail@david-bauer.net>
* hostapd: remove unused mac_buff allocationMartin Weinelt2021-07-061-1/+0
| | | | Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
* hostapd: report bssid, ssid and channel over ubusMartin Weinelt2021-07-061-0/+38
| | | | | | | | | Imports a function from iw to convert frequencies to channel numbers. Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de> [fix potential out of bounds read] Signed-off-by: David Bauer <mail@david-bauer.net>
* dnsmasq: use local option for local domain parameterKevin Darbyshire-Bryant2021-07-051-1/+1
| | | | | | | | | '--local' is a synonym for '--server' so let's use '--local' in the resultant config file for uci's 'local' instead of uci's local parameter being turned into '--server'. Slightly less confusion all round. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* iwinfo: build with nl80211 backend only and make sharedJo-Philipp Wich2021-07-021-19/+5
| | | | | | | | | | | Drop support for building the obsolete broadcom-wl backend and always forcibly enable the nl82011 support. This allows us to make the package shared again since no target specific compilation is happening anymore. This will solve various repository coherency issues related to unavailable libiwinfo versions in the long run. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* treewide: unmark selected packages nonsharedPetr Štetiar2021-07-026-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts changes done in commit 72cc44958ef4 ("treewide: mark selected packages nonshared") as it removes the nonshared flag, but keeps the PKG_RELEASE as the PKG_RELEASE bump while adding nonshared flag was incorrect. Unmark uci, ubus, libubox, lua, libnl-tiny and libjson-c as nonshared packages as this fix attempt didn't worked out. Currently the imagebuilder is broken again: openwrt-imagebuilder-21.02.0-rc3-ipq40xx-generic.Linux-x86_64$ make image PROFILE=avm_fritzbox-7530 PACKAGES=luci-ssl-openssl ... Collected errors: * pkg_hash_check_unresolved: cannot find dependency libiwinfo20210430 for luci-mod-status * pkg_hash_fetch_best_installation_candidate: Packages for luci-mod-status found, but incompatible with the architectures configured * pkg_hash_check_unresolved: cannot find dependency libiwinfo20210430 for rpcd-mod-iwinfo * pkg_hash_fetch_best_installation_candidate: Packages for rpcd-mod-iwinfo found, but incompatible with the architectures configured * satisfy_dependencies_for: Cannot satisfy the following dependencies for luci-ssl-openssl: * libiwinfo20210430 * opkg_install_cmd: Cannot install package luci-ssl-openssl. Everything because iwinfo's ABI was changed two times since rc3 release: +IWINFO_ABI_VERSION:=20210430 +IWINFO_ABI_VERSION:=20210420 Since iwinfo is marked as nonshared, it wasn't built by phase2 builders, but luci-mod-status was already updated 2 times since rc3 and was thus rebuilt by phase2 builders: d1d452ed2fb3 luci-mod-status: don't set '-' hostname when creating static lease 95b3633055c1 luci-mod-status: switch to html table for wlan channel analysis So now luci-mod-status depends on libiwinfo20210430 but only libiwinfo20210106 can be downloaded. This is first part of the fix, in the upcoming commit Jo is going to remove nonshared flag from iwinfo package as well. References: https://lists.infradead.org/pipermail/openwrt-devel/2021-July/035736.html References: https://lists.infradead.org/pipermail/openwrt-devel/2021-July/035741.html Acked-by: Jo-Philipp Wich <jo@mein.io> Reported-by: Nick Hainke <vincent@systemli.org> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* package/comgt: Handle bind/unbind eventsArjun AK2021-07-021-0/+2
| | | | | | | | | | | | | This script was expecting only add/remove events which has not been the case since Kernel 4.12 (which added bind/unbind). Bind events were getting treated as remove events which would cause hotplugged 3g modems to not work. More info: https://lkml.org/lkml/2018/12/23/128 https://github.com/systemd/systemd/issues/8221 Signed-off-by: Arjun AK <arjunak234@gmail.com>
* ubus: update to the latest versionFelix Fietkau2021-06-301-3/+3
| | | | | | 4fc532c8a55b ubusd: fix tx_queue linked list usage Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: backport fix for nl80211 control port tx (fixes FS#3857)Felix Fietkau2021-06-307-17/+133
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix a regression in starting aggregation sessions on mesh interfacesFelix Fietkau2021-06-291-0/+112
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* dnsmasq: distinct Ubus names for multiple instancesEtan Kissling2021-06-291-3/+29
| | | | | | | | | | | | | | | | | | | | | | | | Currently, when using multiple dnsmasq instances they are all assigned to the same Ubus instance name. This does not work, as only a single instance can register with Ubus at a time. In the log, this leads to `Cannot add object to UBus: Invalid argument` error messages. Furthermore, upstream 3c93e8eb41952a9c91699386132d6fe83050e9be changes behaviour so that instead of the log, dnsmasq exits at start instead. With this patch, all dnsmasq instances are assigned unique names so that they can register with Ubus concurrently. One of the enabled instances is always assigned the previous default name "dnsmasq" to avoid breaking backwards compatibility with other software relying on that default. Previously, a random instance got assigned that name (while the others produced error logs). Now, the first unnamed dnsmasq config section is assigned the default name. If there are no unnamed dnsmasq sections the first encountered named dnsmasq config section is assigned instead. A similar issue exists for Dbus and was similarly addressed. Signed-off-by: Etan Kissling <etan.kissling@gmail.com> [tweaked commit message] dnsmasq was not crashing it is exiting Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* base-files: wifi: tidy up the reconf codeBob Cantor2021-06-281-1/+2
| | | | | | | | | | | | commit 5edbd390d321532d9a697d6895a1a7c71c40bd5d rearranged the "wifi up" code. This commit tidies up the "wifi reconf" code so as to keep it aligned with the "wifi up" code. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* base-files: wifi: swap the order of some ubus callsBob Cantor2021-06-281-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | "/sbin/wifi up" makes three ubus calls: 1. ubus call network reload 2. ubus call network.wireless down 3. ubus call network.wireless up The first and third ubus calls call drv_mac80211_setup, while the second ubus call triggers wireless_device_setup_cancel, so the call sequence becomes, 1. drv_mac80211_setup 2. wireless_device_setup_cancel 3. drv_mac80211_setup This commit swaps the order of the first two ubus calls, 1. ubus call network.wireless down 2. ubus call network reload 3. ubus call network.wireless up Consequently drv_mac80211_setup is only called once, and two related bugs (#FS3784 and #FS3902) are no longer triggered by /sbin/wifi. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* mac80211: print an error if wifi teardown failsBob Cantor2021-06-281-0/+4
| | | | | | | | | drv_mac80211_teardown fails silently if the device to be torn down is not defined. This commit prints an error message. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* mac80211: always call wireless_set_data (FS#3784)Bob Cantor2021-06-281-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When wifi is turned off, drv_mac80211_teardown sometimes fails (silently) because the device to be torn down is not defined. This situation arises if drv_mac80211_setup was called twice when wifi was turned on. This commit ensures that the device to be torn down is always defined in drv_mac80211_teardown. Steps to reproduce: 1) Use /sbin/wifi to turn on wifi. uci set wireless.@wifi-iface[0].disabled=0 uci set wireless.@wifi-device[0].disabled=0 uci commit wifi 2) Use /sbin/wifi to turn off wifi. uci set wireless.@wifi-device[0].disabled=1 uci commit wifi 3) Observe that wifi is still up. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* mac80211: fix no_reload logic (FS#3902)Bob Cantor2021-06-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If drv_mac80211_setup is called twice with the same wifi configuration, then the second call returns early with error HOSTAPD_START_FAILED. (wifi works nevertheless, despite the fact that setup is incomplete. But "ubus call network.wireless status" erroneously reports that radio0 is down.) The relevant part of drv_mac80211_setup is, if [ "$no_reload" != "0" ]; then add_ap=1 ubus wait_for hostapd local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")" ret="$?" [ "$ret" != 0 -o -z "$hostapd_res" ] && { wireless_setup_failed HOSTAPD_START_FAILED return } wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1 fi This commit sets no_reload = 0 during the second call of drv_mac80211_setup. It is perhaps worth providing a way to reproduce the situation where drv_mac80211_setup is called twice. When /sbin/wifi is used to turn on wifi, uci set wireless.@wifi-iface[0].disabled=0 uci set wireless.@wifi-device[0].disabled=0 uci commit wifi /sbin/wifi makes the following ubus calls, ubus call network reload ubus call network.wireless down ubus call network.wireless up The first and third ubus calls both call drv_mac80211_setup, while the second ubus call triggers wireless_device_setup_cancel. So the call sequence becomes, drv_mac80211_setup wireless_device_setup_cancel drv_mac80211_setup In contrast, when LuCI is used to turn on wifi only a single call is made to drv_mac80211_setup. branches affected: trunk, 21.02 Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
* iwinfo: update to the latest versionFelix Fietkau2021-06-281-3/+3
| | | | | | c9b1672f5a83 nl80211: fix path compatibility issue Signed-off-by: Felix Fietkau <nbd@nbd.name>
* zram-swap: clean up the log messagesRui Salvaterra2021-06-271-8/+8
| | | | | | | | Remove redundant tags and name things more consistently. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [removed superflous dash] Signed-off-by: Paul Spooren <mail@aparcar.org>
* zram-swap: set the zram swap priority to 100 by defaultRui Salvaterra2021-06-271-2/+5
| | | | | | | New swap devices are added in decreasing priority order, starting at -1. Make sure the zram swap device has the highest priority, by default. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* busybox: sysntpd: add trigger to reload serverAlexey Dobrovolsky2021-06-271-2/+22
| | | | | | | | | | | | sysntpd server becomes unavailable if the index of the bound interface changes. So let's add an interface trigger to reload sysntpd. This patch also adds the ability for the sysntpd script to handle uci interface name from configuration. Fixes: 4da60500ebd2 ("busybox: sysntpd: option to bind server to iface") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
* dante: move to packages.gitPaul Spooren2021-06-263-207/+0
| | | | | | | Rather than maintaining it in core, move it to packages.git where it's maintained by a community. Signed-off-by: Paul Spooren <mail@aparcar.org>
* Revert "dnsmasq: Update to version 2.86test3"Kevin Darbyshire-Bryant2021-06-262-5/+5
| | | | | | | | This reverts commit 3628870015ef46eacf2c936f36e3c1ed3b4c9855. dnsmasq v2.86test3 has some issues with ubus, so is being reverted. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* Revert "dnsmasq: add config option for connmark DNS filtering"Kevin Darbyshire-Bryant2021-06-261-12/+0
| | | | | | | | | This reverts commit dea4bae7c2b963af02e1e3e3bdb5cd656a5ea3d3. dnsmasq v2.86test3 has some issues with ubus and needs reverting, hence this needs reverting. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* dnsmasq: add config option for connmark DNS filteringEtan Kissling2021-06-261-0/+12
| | | | | | | | This adds uci support to configure connmark based DNS filtering. Signed-off-by: Etan Kissling <etan_kissling@apple.com> (See https://lists.thekelleys.org.uk/pipermail/dnsmasq-discuss/2021q2/015151.html) Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
* dnsmasq: Update to version 2.86test3Etan Kissling2021-06-262-5/+5
| | | | | | | | | | | | | | Need this version to add config option for connmark DNS filtering. Summary of upstream CHANGELOG: * Handle DHCPREBIND requests in the DHCPv6 server code. * Fix bug which caused dnsmasq to lose track of processes forked. * Major rewrite of the DNS server and domain handling code. * Revise resource handling for number of concurrent DNS queries. * Improve efficiency of DNSSEC. * Connection track mark based DNS query filtering. Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
* base-files: fix /tmp/TZ when zoneinfo not installedPaul Spooren2021-06-241-7/+4
| | | | | | | | | | | | The zoneinfo packages are not installed per default so neither /tmp/localtime nor /tmp/TZ is generated. This patch mostly reverts the previous fix and instead incooperates a solution suggested by Jo. Fixes "base-files: fix zoneinfo support " 8af62ed Signed-off-by: Paul Spooren <mail@aparcar.org>
* zram-swap: robustify mkswap/swapon/swapoff invocationRui Salvaterra2021-06-242-36/+13
| | | | | | | | | | | Instead of assuming /sbin contains the correct BusyBox symlinks, directly invoke the busybox executable. The required utilities are guaranteed to be present, since the zram-swap package selects them. Additionally, don't assume busybox resides in /bin, rely on PATH to find it. While at it, update the copyright year, use SPDX and switch to AUTORELEASE. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: add support for providing vendor specific IE elementsFelix Fietkau2021-06-241-1/+4
| | | | | | They can be added as hex digit strings via the 'vendor_elements' option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hostapd: add default_disabled option to the supplicantRaphaël Mélotte2021-06-231-2/+8
| | | | | | | | | | | | | | | | | | | | | | | With the default configuration we generate, the supplicant starts scanning and tries to connect to any open network when the interface is enabled. In some cases it can be desirable to prevent the supplicant from scanning by itself. For example, if on the same radio an AP is configured and an unconfigured STA is added (to be configured with WPS), the AP might not be able to beacon until the STA stops scanning. In such a case, the STA configuration can still be required to set specific settings (e.g. multi_ap_backhaul_sta) so it can't be set to "disabled" in uci (because that would prevent the supplicant from being run at all). The alternative is to add the "disabled" parameter to the default network block in the supplicant configuration. This patch adds a "default_disabled" setting in UCI which, when set, adds the "disabled" parameter to the supplicant default network block. Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
* base-files: fix zoneinfo supportRosen Penev2021-06-231-7/+9
| | | | | | | | | | | | | | | | The system init script currently sets /tmp/localinfo when zoneinfo is populated. However, zoneinfo has spaces in it whereas the actual files have _ instead of spaces. This made the if condition never return true. Example failure when removing the if condition: /tmp/localtime -> /usr/share/zoneinfo/America/Los Angeles This file does not exist. America/Los_Angeles does. Ran through shfmt -w -ci -bn -sr -s Signed-off-by: Rosen Penev <rosenp@gmail.com>
* base-files: bring up vlan interface tooLuiz Angelo Daros de Luca2021-06-221-0/+3
| | | | | | | Vlan subinterface was never brought up when using vlan-based preinit network. Tested forcing ifname="" before preinit_ip() on a Tp-Link Archer C5v4. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* base-files: failsafe: Remove the VLAN modifier from interface nameHauke Mehrtens2021-06-221-0/+2
| | | | | | | Some interfaces have a VLAN modifier like :t in lan1:t, this modifier should be removed from the interface before calling preinit_ip_config(). Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* base-files: failsafe: Fix IP configurationHauke Mehrtens2021-06-221-3/+9
| | | | | | | | | | | | | Adapt the preinit_config_board() to the board.json network changes. It now looks for the device and the ports variables to configure the LAN network. This works with swconfig configurations. Fixes: FS#3866 Fixes: d42640e389a8 ("base-files: use "ports" array in board.json network for bridges") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: crypto: limit crypto-hw-hifn-795x to devices with pci supportAleksander Jan Bajkowski2021-06-221-1/+1
| | | | | | | CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on devices with pci support. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* hostapd: make wnm_sleep_mode_no_keys configurableTimo Sigurdsson2021-06-221-3/+7
| | | | | | | | | | | | In the aftermath of the KRACK attacks, hostapd gained an AP-side workaround against WNM-Sleep Mode GTK/IGTK reinstallation attacks. WNM Sleep Mode is not enabled by default on OpenWrt, but it is configurable through the option wnm_sleep_mode. Thus, make the AP-side workaround configurable as well by exposing the option wnm_sleep_mode_no_keys. If you use the option wpa_disable_eapol_key_retries and have wnm_sleep_mode enabled, you might consider using this workaround. Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
* base-files: fix enabled for services with only STOPKarel Kočí2021-06-221-1/+6
| | | | | | | | | | | | | | | There are services that have only STOP value set. They are executed only on shutdown and it is common to use them for system cleanup. There is one such service shipped directly with base-files, it is 'umount'. Those work the same way as those with START but enabled does not report them as enabled although it should have as they can be enabled and disabled as any other service. This also changes check from check for executable to check for symbolic link. The implementation depends on those being links to service file and it is much cleaner and direct to check for them being links. Signed-off-by: Karel Kočí <karel.koci@nic.cz>
* bcm63xx-cfe: update to the latest masterRafał Miłecki2021-06-221-4/+4
| | | | | | e5050f3 linksys: ea9500-v2: add cferam file Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* hostapd: fix handling of the channel utilization optionsTimo Sigurdsson2021-06-211-0/+2
| | | | | | | | | | | | Commit 0a7657c ("hostapd: add channel utilization as config option") added the two new uci options bss_load_update_period and chan_util_avg_period. However, the corresponding "config_add_int" calls for these options weren't added, so attempting to actually use these options and change their values is bound to fail - they always stay at their defaults. Add the missing code to actually make these options work. Fixes: 0a7657c ("hostapd: add channel utilization as config option") Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
* hostapd: make country3 option configurableTimo Sigurdsson2021-06-211-2/+3
| | | | | | | | | The country3 option in hostapd.conf allows the third octet of the country string to be set. It can be used e.g. to indicate indoor or outdoor use (see hostapd.conf for further details). Make this option configurable but optional in OpenWrt. Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
* ustream-ssl: variants conflict with each otherKarel Kočí2021-06-211-1/+3
| | | | | | | | This adds conflicts between variants of libustream pacakge. They provide the same file and thus it should not be possible to install them side by side. Signed-off-by: Karel Kočí <karel.koci@nic.cz>
* grub2: update to 2.06Dirk Neukirchen2021-06-213-59/+19
| | | | | | | | | | | | | | | -300-CVE-2015-8370.patch is upstreamed with different code (upstream id: 451d80e52d851432e109771bb8febafca7a5f1f2) - fixup OpenWrts setup_root patch compile tested: x86_64,i386 runtime tested: VM x86_64,VM i386 - booted fine - grub-editenv worked Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
* kernel/modules: make sure igb loads at bootChris Blake2021-06-211-1/+1
| | | | | | | | | | Without loading the igb at boot, the recovery wouldn't have network available. All network drivers should be loaded before etc/board.d/02_network is called. Note that other network drivers already have this set, such as tg3. Fixes: 7e0e5110bc90 ("kernel: add igb kernel module") Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* uci: add uci_revert functionFlorian Eckert2021-06-212-1/+9
| | | | | | Add missing uci_revert shell function wrapper. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-29 18:56:49 +0000