aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* tplink-safeloader: add support for TP-Link Archer A7 v5 (RU)Alexey Kunitskiy2021-02-051-1/+2
| | | | | | | | | | | | | | | | | | | Although provided in separate zip archives, the firmwares for EU and RU version are byte-identical. This adds the missing ID compared to the support-list in the vendor firmware. Note (since I checked it anyway): Partitions and support list are unchanged for all three existing firmware versions: * 20200721-rel40773 * 20201029-rel43238 * 20201120-rel50399 Signed-off-by: Alexey Kunitskiy <alexey.kv@gmail.com> [rewrite commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: wrap ucidef_add_switch in 02_networkAdrian Schmutzler2021-02-051-1/+2
| | | | | | Wrap line to be consistent with all other definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: move elx-header into image-commands.mkYanase Yuki2021-02-052-20/+20
| | | | | | | ELECOM WAB-I1750-PS will need this in ath79, so move it to common Makefile. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* kirkwood: refresh kernel configSungbo Eo2021-02-051-63/+2
| | | | | | Refresh config with make kernel_oldconfig. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* lantiq: change phy-mode to mii for FRITZ!Box 7412Aleksander Jan Bajkowski2021-02-051-1/+1
| | | | | | | | | | | FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is more accurate in this case. Gmii is used by Gigabit ethernet PHYs. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Reviewed-by: Mathias Kresin <dev@kresin.me> [minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: replace full-text BSC license by SPDX identifierAdrian Schmutzler2021-02-051-27/+1
| | | | | | | | | | This replaces a full-text BSD clause by the corresponding SPDX identifier. This should make it easier to identify the license both by humans and machines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: replace full-text licenses by SPDX identifierAdrian Schmutzler2021-02-0512-269/+12
| | | | | | | | | | This replaces several full-text and abbreviated licenses found in DTS files by the corresponding SPDX identifiers. This should make it easier to identify the license both by humans and machines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for UniElec U7621-01David Bentham2021-02-053-0/+174
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UniElec U7621-01 is a router platform board, the smaller model of the U7621-06. The device has the following specifications: - MT7621AT (880 MHz) - 256 of RAM (DDR3) - 16 MB of FLASH (SPI NOR) - 5x 1 Gbps Ethernet (MT7621 built-in switch) - 1x 2.4Ghz MT7603E - 1x 5Ghz MT7612 - 1x miniPCIe slots (PCIe bus only) - 1x miniSIM slot - 1x USB 2.0 (uses the usb 3.0 driver) - 8x LEDs (1x GPIO-controlled) - 1x reset button - 1x UART header (4-pins) - 1x GPIO header (30-pins) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - 1x 2.4Ghz MT7603E (wifi) - 1x 5Ghz MT7612 (wifi) - miniPCIe slots (tested with Wi-Fi cards and LTE modem cards) - miniSIM slot (works with normal size simcard) - sysupgrade - reset button Installation: This board has no locked down bootloader. The seller can be asked to install openwrt v18.06, so upgrades are standard sysupgrade method. Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. LEDs list (left to right): - ESW_P0_LED_0 - ESW_P1_LED_0 - ESW_P2_LED_0 - ESW_P3_LED_0 - ESW_P4_LED_0 - CTS2_N (GPIO10, configured as "status" LED) - LED_WLAN# (connected with pin 44 in wifi1 slot) Signed-off-by: David Bentham <db260179@gmail.com> [add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Meraki MR12Martin Kennedy2021-02-057-9/+209
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Port device support for Meraki MR12 from the ar71xx target to ath79. Specifications: - SoC: AR7242-AH1A CPU - RAM: 64MiB (NANYA NT5DS32M16DS-5T) - NOR Flash: 16MiB (MXIC MX25L12845EMI-10G) - Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY) - Ethernet: 1 x 100Mbit port (SoC MAC+PHY) - Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n) Installation: 1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins 2. Open shell case 3. Connect a USB->TTL cable to headers furthest from the RF shield 4. Power on the router; connect to U-boot over 115200-baud connection 5. Interrupt U-boot process to boot Openwrt by running: setenv bootcmd bootm 0xbf0a0000; saveenv; tftpboot 0c00000 <filename-of-initramfs-kernel>.bin; bootm 0c00000; 6. Copy sysupgrade image to /tmp on MR12 7. sysupgrade /tmp/<filename-of-sysupgrade>.bin Notes: - kmod-owl-loader is still required to load the ART partition into the driver. - The manner of storing MAC addresses is updated from ar71xx; it is at 0x66 of the 'config' partition, where it was discovered that the OEM firmware stores it. This is set as read-only. If you are migrating from ar71xx and used the method mentioned above to upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more method for doing this is described below. - Migrating directly from ar71xx has not been thoroughly tested, but one method has been used a couple of times with good success, migrating 18.06.2 to a full image produced as of this commit. Please note that these instructions are only for experienced users, and/or those still able to open their device up to flash it via the serial headers should anything go wrong. 1) Install kmod-mtd-rw and uboot-envtools 2) Run `insmod mtd-rw.ko i_want_a_brick=1` 3) Modify /etc/fw_env.config to point to the u-boot-env partition. The file /etc/fw_env.config should contain: # MTD device env offset env size sector size /dev/mtd1 0x00000 0x10000 0x10000 See https://openwrt.org/docs/techref/bootloader/uboot.config for more details. 4) Run `fw_printenv` to verify everything is correct, as per the link above. 5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address. 6) Manually modify /lib/upgrade/common.sh's get_image function: Change ... cat "$from" 2>/dev/null | $cmd ... into ... ( dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes echo -ne '\x00\x18\x0a\x12\x34\x56' ; # Add in MAC address dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest cat "$from" 2>/dev/null ) | $cmd ... which, during the upgrade process, will pad the image by 128K of zeroes-plus-MAC-address, in order for the ar71xx's firmware partition -- which starts at 0xbf080000 -- to be instead aligned with the ath79 firmware partition, which starts 128K later at 0xbf0a0000. 7) Copy the sysupgrade image into /tmp, as above 8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait Again, this may BRICK YOUR DEVICE, so make *sure* to have your serial cable handy. Signed-off-by: Martin Kennedy <hurricos@gmail.com> [add LED migration and extend compat message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Hi-Link HLK-7688AEwan Parker2021-02-054-0/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7688AN - RAM: 128 MB - Flash: 32 MB - Ethernet: 5x 10/100 (1x WAN, 4x LAN) - Wireless: built in 2.4GHz (bgn) - USB: 1x USB 2.0 port - Buttons: 1x Reset - LEDs: 1x (WiFi) Flash instructions: - Configure TFTP server with IP address 10.10.10.3 - Name the firmware file as firmware.bin - Connect any Ethernet port to the TFTP server's LAN - Choose option 2 in U-Boot - Alternatively choose option 7 to upload firmware to the built-in web server MAC addresses as verified by OEM firmware: use address source 2g *:XX factory 0x4 LAN *:XX+1 factory 0x28 WAN *:XX+1 factory 0x2e Notes: This board is ostensibly a module containing the MediaTek MT7688AN SoC, 128 MB DDR2 SDRAM and 32 MB flash storage. The SoC can be operated in IoT Gateway Mode or IoT Device Mode. From some vendors the U-Boot that comes installed operates on UART 2 which is inaccessible in gateway mode and operates unreliably in the Linux kernel when using more than 64 MB of RAM. For those, updating U-Boot is recommended. Signed-off-by: Ewan Parker <ewan@ewan.cc> [add WLAN to 01_leds] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* build: use SPDX license tagsPaul Spooren2021-02-0538-175/+72
| | | | | | | | | The license folder is a core part of OpenWrt and all GPL-2.0 licensed. Use SPDX license tags to allow machines to check licenses. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, keep some Copyright lines, sharpen commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* selinux-policy: update to version 0.6Daniel Golle2021-02-051-2/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add defaults for new SELinux optionsDaniel Golle2021-02-051-0/+10
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.4 to 5.4.95John Audia2021-02-043-40/+3
| | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Removed upstreamed patches: imx6: 303-ARM-dts-imx6qdl-gw52xx-fix-duplicate-regulator-namin.patch Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* hostapd: add forgotten patch for P2P vulnerability fixPetr Štetiar2021-02-042-1/+39
| | | | | | | | Commit 7c8c4f1be648 ("hostapd: fix P2P group information processing vulnerability") was missing the actual patch for the vulnerability. Fixes: 7c8c4f1be648 ("hostapd: fix P2P group information processing vulnerability") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* hostapd: fix P2P group information processing vulnerabilityDaniel Golle2021-02-041-1/+1
| | | | | | | | | | | A vulnerability was discovered in how wpa_supplicant processing P2P (Wi-Fi Direct) group information from active group owners. This issue was discovered by fuzz testing of wpa_supplicant by Google's OSS-Fuzz. https://w1.fi/security/2020-2/wpa_supplicant-p2p-group-info-processing-vulnerability.txt Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* trusted-firmware-a.mk: add PKG_CPE_IDDaniel Golle2021-02-041-0/+1
| | | | | | | Vulnerabilities of Trusted Firmware A are tracked as cpe:/a:arm:arm_trusted_firmware Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-mediatek: make use of trusted-firmware-a.mkDaniel Golle2021-02-031-10/+6
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* tfa-layerscape: don't build fiptoolDaniel Golle2021-02-031-8/+3
| | | | | | tfa-fiptool is now provided by an extra package. Use that instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* arm-trusted-firmware-tools: add packageDaniel Golle2021-02-031-0/+70
| | | | | | | Package ARM Trusted Firmware host tools separately. (instead of building tfa-fiptool as part of tfa-layerscape) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* iptables: update to 1.8.7Curtis Deptuck2021-02-021-2/+2
| | | | | | | | | | ChangeLog: https://netfilter.org/projects/iptables/files/changes-iptables-1.8.7.txt Refresh patch: None required Signed-off-by: Curtis Deptuck <curtdept@me.com>
* bcm63xx: sprom: override the PCI device IDDaniel González Cabanelas2021-02-022-1/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PCI device ID detected by the wifi drivers on devices using a fallback SPROM is wrong. Currently the chipnum is used for this parameter. Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on devices without a physical SPROM, the only one way to detect if the device suports both bands or only the 5GHz band, is by reading the device ID from the fallback SPROM. In some devices, this may lead to a non working wifi on a 5GHz-only card, or in the best case a working 2.4GHz-only in a dual band wifi card. The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is 0x0060. This is true for any SPROM version. Override the PCI device ID with the one defined at the fallback SPROM, to detect the correct wifi card model and allow using the 5GHz band if supported. The patch has been tested with the following wifi radios: BCM43222: b43: both 2.4/5GHz working brcm-wl: both 2.4/5GHz working BCM43225: b43: 2.4GHz, working brcmsmac: working brcm-wl: it lacks support BCM43217: b43: 2.4GHz, working brcmsmac: it lacks support brcm-wl: it lacks support Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> [amend commit description, rework patch to avoid using a new global variable and keep ssb sprom extraction code as close to ssb/pci.c as possible] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: backport upstream SSB SPROM extractionÁlvaro Fernández Rojas2021-02-026-38/+102
| | | | | | | New upstream changes extract more SPROM values and fix the antenna gain. These changes can be found in linux drivers/ssb/pci.c. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* arm-trusted-firmware-mediatek: add ATF builds for MT7622Daniel Golle2021-02-021-0/+111
| | | | | | | | | | | | | | ATF bl2 comes in 4 variants for MT7622 depending on the boot media: * nor * snand * emmc * sdmmc Additional binary headers needed for emmc and sdmmc are downloaded as well and provided along with bl2*.bin and bl31.bin to allow building images including ATF for MT7622. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* procd: update to git HEADDaniel Golle2021-02-021-4/+4
| | | | | | | | | | 0aee1c3 hotplug.c: set nl_pid to zero d6dda31 procd: fix compiler warning 92c8e8f jail: remove duplicate check for hook file permissions 0a74c06 jail: only output BPF instr. table header if debugging fd18379 jail: cgroups: fix uninitialized variabl Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.4 to 5.4.94John Audia2021-02-019-31/+31
| | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build-tested: bcm27xx/bcm2711, ipq806x/R7800, Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* mac80211: fix station rate table updates on assocFelix Fietkau2021-02-011-0/+38
| | | | | | | | If the driver uses .sta_add, station entries are only uploaded after the sta is in assoc state. Fix early station rate table updates by deferring them until the sta has been uploaded Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: fix incorrect parameterDavid Bauer2021-02-011-1/+1
| | | | | | | he_mu_beamformer only accepts values of 0 and 1 according to the hostapd documentation. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: add ethtool statistics supportLeon Leijssen2021-02-011-0/+86
| | | | | | | | | Add statistics to ethtool. The statistics can be useful to debug network issues. The code is backported from mainline ag71xx.c driver. Signed-off-by: Leon Leijssen <leon.git@leijssen.info>
* uboot-rockchip: fix RockPro64 boot from eMMCMarty Jones2021-02-011-0/+27
| | | | | | | | | | | With upstream commit f81f9f0ebac5 ("rockchip: rockpro64: initialize USB in preboot") CONFIG_USE_PREBOOT was enabled on the RockPro64, which is causing boot issues when a eMMC is used, as a workaround will temporarily disable this option. Signed-off-by: Marty Jones <mj8263788@gmail.com> [Improve patch description] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for Ubiquiti UniFi AP Outdoor+David Bauer2021-02-016-55/+180
| | | | | | | | | | | | | | | | | | | Hardware -------- Atheros AR7241 16M SPI-NOR 64M DDR2 Atheros AR9283 2T2R b/g/n 2x Fast Ethernet (built-in) Installation ------------ Transfer the Firmware update to the device using SCP. Install using fwupdate.real -m <openwrt.bin> -d Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: convert UniFi Outdoor+ HSR support to OFDavid Bauer2021-02-012-27/+10
| | | | | | | | Enable support for the Ubiquiti UniFi Outdoor+ RF filter via device-tree. The old way of using platform data is not required anymore, as it was only used on the now removed ar71xx target. Signed-off-by: David Bauer <mail@david-bauer.net>
* util-linux: remove custom pkgconfig patchRosen Penev2021-01-312-77/+11
| | | | | | | | | | | Replace with sed as done elsewhere. Fixes error with at least btrfs-progs: Package '@LIBSELINUX@', required by 'mount', not found Package '@LIBCRYPTSETUP@', required by 'mount', not foun Signed-off-by: Rosen Penev <rosenp@gmail.com>
* selinux-policy: update to git tag v0.5Daniel Golle2021-01-311-2/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* glibc: update to latest 2.32 commit (bug 27256)Hans Dedecker2021-01-311-2/+2
| | | | | | 760e1d2878 gconv: Fix assertion failure in ISO-2022-JP-3 module (bug 27256) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mvebu: omnia: make initramfs image usable out of the boxPetr Štetiar2021-01-311-2/+2
| | | | | | | | | | | | | | | Currently it's not possible to boot the device with just initramfs image without additional effort as the initramfs image doesn't contain device tree. Fix it by producing FIT based image which could be booted with following commands: setenv bootargs earlyprintk console=ttyS0,115200 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin bootm ${kernel_addr_r} Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* tools/zstd: compile with cmakeRosen Penev2021-01-302-3/+9
| | | | | | | | It's faster and more reliable. Removed ccache cmake build dependency as it's now implicit. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/zstd: update to 1.4.8Rosen Penev2021-01-302-65/+3
| | | | | | | Switch to the normal tarball instead of the codeload generated one. The latter has the potential to change hashes based on changes in the repo. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* rules: fix empty COMMITCOUNT/AUTORELEASEPaul Spooren2021-01-301-2/+2
| | | | | | | | | | | | | | | | | | | | | Packages that are in-tree only often lack a PKG_VERSION and only use the PKG_RELEASE to mark changes. Using COMMITCOUNT/AUTORELEASE variables causes an issue as both variables are empty during the metadata DUMP phase. Instead of leaving these variables empty and causing an error message like below, set the variables to 0 during dumping. On actual building the variable is evaluated causing in a value above 0. ERROR: please fix package/utils/px5g-wolfssl/Makefile - \ see logs/package/utils/px5g-wolfssl/dump.txt for details Makefile:48: *** Package/px5g-wolfssl is missing the VERSION field. Stop. Reported-by: Daniel Golle <daniel@makrotopia.org> Reported-by: Stijn Segers <foss@volatilesystems.org> Reported-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Paul Spooren <mail@aparcar.org>
* odhcpd: update to latest git HEADHans Dedecker2021-01-301-3/+3
| | | | | | 8d8a8cd dhcpv6-ia: apply prefix_filter on dhcpv6 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* trusted-firmware-a.mk: pass package version as version identifierAndre Heider2021-01-301-0/+1
| | | | | | | Upon boot it now prints: NOTICE: BL1: v2.4(release):OpenWRT v2.4-1 (espressobin-v3-v5-1gb-2cs) (Marvell-devel-18.12.0) Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: pass commit ids to a3700-utils/mv-ddr-marvellAndre Heider2021-01-303-0/+29
| | | | | | | | | The two required tools fail to identify their version when not compiling from a git clone, patch that in and pass on the used commit hashes. Upon boot it now prints "WTMI-devel-18.12.1-5598e150". Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: bump espressobin boards to CPU_1000_DDR_800Andre Heider2021-01-301-6/+6
| | | | | | | | | | | | | The cpufreq issue has been identified and a fix is in the process of beeing upstreamed [0]. Bump the boards to the default 1000MHz so they can run at that frequency once the fix is merged. Until then the boards are stuck at 800MHz (just claiming to run 1000Hz, which is a lie). [0] https://lore.kernel.org/linux-arm-kernel/20210114124032.12765-1-pali@kernel.org/ Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: update to v2.4Andre Heider2021-01-302-12/+12
| | | | Signed-off-by: Andre Heider <a.heider@gmail.com>
* uboot-mvebu: update to v2021.01Andre Heider2021-01-304-533/+2
| | | | | | | u-boot now detects emmc variants at runtime, we don't need to build seperate binaries anymore. Signed-off-by: Andre Heider <a.heider@gmail.com>
* arm-trusted-firmware-mvebu: don't build emmc variantsAndre Heider2021-01-301-55/+0
| | | | | | | Starting with u-boot v2021.01 a single binary will be used for non-emmc and emmc variants. Signed-off-by: Andre Heider <a.heider@gmail.com>
* mvebu: LS421DE: fix the thermal zonesDaniel González Cabanelas2021-01-301-13/+42
| | | | | | | | | | | | | | | | | | | | | | The thermal zones kernel documentation is misleading, we cannot use more than one sensor in a thermal zone node. Furthermore the drivetemp driver for some reason it only catches one sensor from the hard drives array (the first available). In the Buffalo Linkstation LS421DE board there is also a sensor at the ethernet phy chip that can also be monitored. Very useful to stop the fan when there are no hard drives in the bays. (It might be also possible to add the CPU sensor, but it requires kernel patching for registering the sensor via device tree, using the function: devm_thermal_zone_of_sensor_register) Fix the thermal zones to use only one sensor per node and add the ethernet phy sensor. Also adjust the hdd temperatures to be more conservative for a mechanical hard drive. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* strace: update package to v5.10Geordan Neukum2021-01-301-2/+2
| | | | | | | | | | v5.10 has been released for strace. As such, let's go ahead bring in the latest version of this package. See here for the changelog: https://github.com/strace/strace/releases/tag/v5.10 Signed-off-by: Geordan Neukum <gneukum1@gmail.com>
* base-files: mount pstore if presentBrian Norris2021-01-291-0/+1
| | | | | | | | Pstore (persistent store) can be used to stash debug information (kernel console, panics, ftrace) across reboots or crashes. If the filesystem is present, mount it. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* ath10k-ct: update to latest versionMichael Yartys2021-01-291-3/+3
| | | | | | | | | Changelog: - ath10k-ct: Pull in some upstream patches. Runtime-tested on ipq806x (Netgear R7800). Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-01 03:36:41 +0000