aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/ipq806x')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/01_leds3
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata6
-rw-r--r--target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts430
-rw-r--r--target/linux/ipq806x/image/Makefile14
-rw-r--r--target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch3
6 files changed, 457 insertions, 3 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index c23f25540b..fed821663a 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -27,6 +27,9 @@ nec,wg2600hp)
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt"
ucidef_set_led_switch "wan" "WAN" "green:active" "switch0" "0x2"
;;
+nec,wg2600hp3)
+ ucidef_set_led_switch "wan" "WAN" "green:active" "switch0" "0x2"
+ ;;
netgear,d7800 |\
netgear,r7500 |\
netgear,r7500v2 |\
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index eecf81a8cd..10b2ec0148 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -46,6 +46,10 @@ linksys,ea8500)
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
+nec,wg2600hp3)
+ ucidef_add_switch "switch0" \
+ "2:lan" "3:lan" "4:lan" "5:lan" "0@eth1" "1:wan" "6@eth0"
+ ;;
netgear,r7800 |\
tplink,c2600)
ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index a22af9b676..8788fc92f6 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -24,7 +24,8 @@ case "$FIRMWARE" in
caldata_extract "art" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1)
;;
- nec,wg2600hp)
+ nec,wg2600hp |\
+ nec,wg2600hp3)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary PRODUCTDATA 0x12)
;;
@@ -62,7 +63,8 @@ case "$FIRMWARE" in
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2)
;;
- nec,wg2600hp)
+ nec,wg2600hp |\
+ nec,wg2600hp3)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary PRODUCTDATA 0xc)
;;
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts
new file mode 100644
index 0000000000..d234b94a46
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8062-wg2600hp3.dts
@@ -0,0 +1,430 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq8062.dtsi"
+#include <dt-bindings/input/input.h>
+
+/delete-node/ &nand_pins;
+
+/ {
+ model = "NEC Platforms Aterm WG2600HP3";
+ compatible = "nec,wg2600hp3", "qcom,ipq8062", "qcom,ipq8064";
+
+ memory {
+ device_type = "memory";
+ reg = <0x42000000 0x1e000000>;
+ };
+
+ aliases {
+ label-mac-device = &gmac2;
+
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_red;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&buttons_pins>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ mode0 {
+ label = "mode0";
+ gpios = <&qcom_pinmux 40 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ };
+
+ mode1 {
+ label = "mode1";
+ gpios = <&qcom_pinmux 41 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-0 = <&leds_pins>;
+ pinctrl-names = "default";
+
+ led_power_green: power_green {
+ label = "green:power";
+ gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_power_red: power_red {
+ label = "red:power";
+ gpios = <&qcom_pinmux 35 GPIO_ACTIVE_HIGH>;
+ };
+
+ active_green {
+ label = "green:active";
+ gpios = <&qcom_pinmux 42 GPIO_ACTIVE_HIGH>;
+ };
+
+ active_red {
+ label = "red:active";
+ gpios = <&qcom_pinmux 38 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g_green {
+ label = "green:wlan2g";
+ gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wlan2g_red {
+ label = "red:wlan2g";
+ gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g_green {
+ label = "green:wlan5g";
+ gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g_red {
+ label = "red:wlan5g";
+ gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>;
+ };
+
+ tv_green {
+ label = "green:tv";
+ gpios = <&qcom_pinmux 46 GPIO_ACTIVE_HIGH>;
+ };
+
+ tv_red {
+ label = "red:tv";
+ gpios = <&qcom_pinmux 36 GPIO_ACTIVE_HIGH>;
+ };
+
+ converter_green {
+ label = "green:converter";
+ gpios = <&qcom_pinmux 43 GPIO_ACTIVE_HIGH>;
+ };
+
+ converter_red {
+ label = "red:converter";
+ gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&qcom_pinmux {
+ pinctrl-0 = <&akro_pins>;
+ pinctrl-names = "default";
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <10>;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ buttons_pins: buttons_pins {
+ mux {
+ pins = "gpio22", "gpio24", "gpio40",
+ "gpio41";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ leds_pins: leds_pins {
+ mux {
+ pins = "gpio14", "gpio15", "gpio35",
+ "gpio36", "gpio38", "gpio42",
+ "gpio43", "gpio46", "gpio55",
+ "gpio56", "gpio57", "gpio58";
+ function = "gpio";
+ bias-pull-down;
+ };
+
+ akro2 {
+ pins = "gpio15", "gpio35", "gpio38",
+ "gpio42", "gpio43", "gpio46",
+ "gpio55", "gpio56", "gpio57",
+ "gpio58";
+ drive-strength = <2>;
+ };
+
+ akro4 {
+ pins = "gpio14", "gpio36";
+ drive-strength = <4>;
+ };
+ };
+
+ /*
+ * Stock firmware has the following settings, so let's do the same.
+ * I don't sure why these are required.
+ */
+ akro_pins: akro_pinmux {
+ akro {
+ pins = "gpio17", "gpio26", "gpio47";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ reset {
+ pins = "gpio45";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ gmac0_rgmii {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+};
+
+&gsbi5 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_SPI>;
+
+ spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x0000000 0x0020000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "MIBIB";
+ reg = <0x0020000 0x0020000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "SBL2";
+ reg = <0x0040000 0x0040000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "SBL3";
+ reg = <0x0080000 0x0080000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "DDRCONFIG";
+ reg = <0x0100000 0x0010000>;
+ read-only;
+ };
+
+ partition@110000 {
+ label = "SSD";
+ reg = <0x0110000 0x0010000>;
+ read-only;
+ };
+
+ partition@120000 {
+ label = "TZ";
+ reg = <0x0120000 0x0080000>;
+ read-only;
+ };
+
+ partition@1a0000 {
+ label = "RPM";
+ reg = <0x01a0000 0x0080000>;
+ read-only;
+ };
+
+ partition@220000 {
+ label = "APPSBL";
+ reg = <0x0220000 0x0080000>;
+ read-only;
+ };
+
+ partition@2a0000 {
+ label = "APPSBLENV";
+ reg = <0x02a0000 0x0010000>;
+ read-only;
+ };
+
+ factory: partition@2b0000 {
+ label = "PRODUCTDATA";
+ reg = <0x02b0000 0x0030000>;
+ read-only;
+ };
+
+ partition@2e0000 {
+ label = "ART";
+ reg = <0x02e0000 0x0040000>;
+ read-only;
+ };
+
+ partition@320000 {
+ label = "TP";
+ reg = <0x0320000 0x0040000>;
+ read-only;
+ };
+
+ partition@360000 {
+ label = "TINY";
+ reg = <0x0360000 0x0500000>;
+ read-only;
+ };
+
+ partition@860000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x0860000 0x17a0000>;
+ };
+ };
+ };
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+
+ qcom,ath10k-calibration-variant = "NEC-Platforms-WG2600HP3";
+ };
+ };
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+
+ ieee80211-freq-limit = <2400000 2483000>;
+ qcom,ath10k-calibration-variant = "NEC-Platforms-WG2600HP3";
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x04 0x80080080 /* PAD0_MODE */
+ 0x0c 0x06000000 /* PAD6_MODE */
+ 0x10 0x002613a0 /* PWS_REG */
+ 0x50 0xcc36cc36 /* LED_CTRL0 */
+ 0x54 0xca36ca36 /* LED_CTRL1 */
+ 0x58 0xc936c936 /* LED_CTRL2 */
+ 0x5c 0x03ffff00 /* LED_CTRL3 */
+ 0x7c 0x0000004e /* PORT0_STATUS */
+ 0x94 0x0000004e /* PORT6_STATUS */
+ 0xe0 0xc74164de /* SGMII_CTRL */
+ 0xe4 0x0006a545 /* MAC_PWR_SEL */
+ >;
+ };
+};
+
+&gmac1 {
+ status = "okay";
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ mdiobus = <&mdio0>;
+ mtd-mac-address = <&factory 0x0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ mdiobus = <&mdio0>;
+ mtd-mac-address = <&factory 0x6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index ad7c4b94d2..80bfec5ad9 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -193,6 +193,20 @@ define Device/nec_wg2600hp
endef
TARGET_DEVICES += nec_wg2600hp
+define Device/nec_wg2600hp3
+ $(call Device/LegacyImage)
+ DEVICE_VENDOR := NEC Platforms
+ DEVICE_MODEL := Aterm WG2600HP3
+ SOC := qcom-ipq8062
+ BLOCKSIZE := 64k
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+ DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform -kmod-usb-ohci -kmod-usb2 \
+ -kmod-usb-ledtrig-usbport -kmod-usb-phy-qcom-dwc3 -kmod-usb3 -kmod-usb-dwc3-qcom \
+ ath10k-firmware-qca9984-ct ipq-wifi-nec_wg2600hp3
+endef
+TARGET_DEVICES += nec_wg2600hp3
+
define Device/netgear_d7800
$(call Device/DniImage)
DEVICE_VENDOR := NETGEAR
diff --git a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch
index 6bbf184ac7..795684cdf5 100644
--- a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch
@@ -10,9 +10,10 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -843,6 +843,21 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -843,6 +843,22 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
++ qcom-ipq8062-wg2600hp3.dtb \
qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-c2600.dtb \
+ qcom-ipq8064-d7800.dtb \