ath79: add support for TP-Link TL-WR802N V1 and V2

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
  [V1] http://192.168.0.1
  [V2] http://192.168.0.254
  Default user is "admin" & password is "admin".
  On V2, there is no DHCP server running by default, so remember to set
  IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
  [V1] "*.factory.bin"
  [V2] "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
  Web interface may complain if filename is too long. In such case,
  rename .bin to something shorter.
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Notes:

When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.

The MAC address assignment has been checked with OEM firmware.

Installation manual based on ar71xx support by Thomas Roberts

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

2 files changed, 21 insertions, 1 deletions

diff --git a/target/linux/ath79/tiny/base-files/etc/board.d/02_network b/target/linux/ath79/tiny/base-files/etc/board.d/02_network
index 5e559363b2..bff17bcce8 100755
--- a/target/linux/ath79/tiny/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/tiny/base-files/etc/board.d/02_network
@@ -43,7 +43,9 @@ ath79_setup_interfaces()
 	tplink,tl-wa901nd-v2|\
 	tplink,tl-wa901nd-v4|\
 	tplink,tl-wa901nd-v5|\
-	tplink,tl-wr703n)
+	tplink,tl-wr703n|\
+	tplink,tl-wr802n-v1|\
+	tplink,tl-wr802n-v2)
 		ucidef_set_interface_lan "eth0"
 		;;
 	tplink,tl-mr3220-v1|\
diff --git a/target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration
new file mode 100644
index 0000000000..377135f530
--- /dev/null
+++ b/target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration
@@ -0,0 +1,18 @@
+. /lib/functions.sh
+. /lib/functions/migrations.sh
+
+board=$(board_name)
+boardonly="${board##*,}"
+
+case "$board" in
+tplink,tl-wr802n-v1)
+	migrate_leds ":blue:=:green:"
+	;;
+tplink,tl-wr802n-v2)
+	migrate_leds "^$boardonly:=tp-link:"
+	;;
+esac
+
+migrations_apply system
+
+exit 0