From 7e513136c63108bf55b38be4d2b65aa00b0d2b26 Mon Sep 17 00:00:00 2001 From: Lech Perczak Date: Fri, 29 May 2020 20:50:05 +0200 Subject: ath79: add support for TP-Link TL-WR802N V1 and V2 Specification: - SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc) - RAM: 32 MiB - Storage: 4 MiB of Flash on board - Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) Installation through OEM Web Interface: - Connect to TL-WR802N by Ethernet or Wi-Fi - Go to web interface: [V1] http://192.168.0.1 [V2] http://192.168.0.254 Default user is "admin" & password is "admin". On V2, there is no DHCP server running by default, so remember to set IP manually. - Go to "System Tools -> Firmware Upgrade" - Browse for firmware: [V1] "*.factory.bin" [V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model Web interface may complain if filename is too long. In such case, rename .bin to something shorter. - Click upgrade Installation through tftp: Note: T_OUT, T_IN and GND on the board must be connected to USB TTL Serial Configuration 115200 8n1 - Boot the TL-WR802N - When "Autobooting in 1 seconds" appears type "tpl" followed by enter - Connect to the board Ethernet port (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10) - tftpboot 0x80000000 - Record the result of "printenv bootcmd" - Enter "erase +0x3c0000" (e.g erase 0x9f020000 +0x3c0000) - Enter "cp.b 0x80000000 0x3c0000" (e.g cp.b 0x80000000 0x9f020000 0x3c0000) - Enter "bootm " (e.g bootm 0x9f020000) Notes: When porting from ar71xx target to ath79, I found out that on V2, reset button is on GPIO12 and active low, instead of GPIO11 and active high. By cross-flashing V1 firmware to V2, I confirmed the same is true for V1. Also according to manual of V1, this one also has green LED instead of blue - both of those issues were fixed accordingly. The MAC address assignment has been checked with OEM firmware. Installation manual based on ar71xx support by Thomas Roberts Signed-off-by: Lech Perczak [slightly adjust commit message, add MAC address comment] Signed-off-by: Adrian Schmutzler --- .../linux/ath79/tiny/base-files/etc/board.d/02_network | 4 +++- .../tiny/base-files/etc/uci-defaults/04_led_migration | 18 ++++++++++++++++++ 2 files changed, 21 insertions(+), 1 deletion(-) create mode 100644 target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration (limited to 'target/linux/ath79/tiny/base-files') diff --git a/target/linux/ath79/tiny/base-files/etc/board.d/02_network b/target/linux/ath79/tiny/base-files/etc/board.d/02_network index 5e559363b2..bff17bcce8 100755 --- a/target/linux/ath79/tiny/base-files/etc/board.d/02_network +++ b/target/linux/ath79/tiny/base-files/etc/board.d/02_network @@ -43,7 +43,9 @@ ath79_setup_interfaces() tplink,tl-wa901nd-v2|\ tplink,tl-wa901nd-v4|\ tplink,tl-wa901nd-v5|\ - tplink,tl-wr703n) + tplink,tl-wr703n|\ + tplink,tl-wr802n-v1|\ + tplink,tl-wr802n-v2) ucidef_set_interface_lan "eth0" ;; tplink,tl-mr3220-v1|\ diff --git a/target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration new file mode 100644 index 0000000000..377135f530 --- /dev/null +++ b/target/linux/ath79/tiny/base-files/etc/uci-defaults/04_led_migration @@ -0,0 +1,18 @@ +. /lib/functions.sh +. /lib/functions/migrations.sh + +board=$(board_name) +boardonly="${board##*,}" + +case "$board" in +tplink,tl-wr802n-v1) + migrate_leds ":blue:=:green:" + ;; +tplink,tl-wr802n-v2) + migrate_leds "^$boardonly:=tp-link:" + ;; +esac + +migrations_apply system + +exit 0 -- cgit v1.2.3