aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files/etc/diag.sh
diff options
context:
space:
mode:
authorPiotr Dymacz <pepe2k@gmail.com>2016-12-02 22:42:41 +0100
committerJohn Crispin <john@phrozen.org>2016-12-12 09:57:40 +0100
commitc198ca682c187e61730119134e1dde75da2e7a16 (patch)
tree79a8603079c335003ca982a2fbaaece0a113507a /target/linux/ar71xx/base-files/etc/diag.sh
parent6ae71708c9ced26961f73286d794e1aafedd6c52 (diff)
downloadupstream-c198ca682c187e61730119134e1dde75da2e7a16.tar.gz
upstream-c198ca682c187e61730119134e1dde75da2e7a16.tar.bz2
upstream-c198ca682c187e61730119134e1dde75da2e7a16.zip
ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ar71xx/base-files/etc/diag.sh')
-rw-r--r--target/linux/ar71xx/base-files/etc/diag.sh4
1 files changed, 3 insertions, 1 deletions
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 9b9aea8a77..43ea2b683e 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -18,7 +18,9 @@ get_status_led() {
antminer-s3|\
antminer-r1|\
minibox-v1|\
- som9331)
+ som9331|\
+ sr3200|\
+ xd3200)
status_led="$board:green:system"
;;
ap132|\