aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files
diff options
context:
space:
mode:
authorPiotr Dymacz <pepe2k@gmail.com>2016-12-02 22:42:41 +0100
committerJohn Crispin <john@phrozen.org>2016-12-12 09:57:40 +0100
commitc198ca682c187e61730119134e1dde75da2e7a16 (patch)
tree79a8603079c335003ca982a2fbaaece0a113507a /target/linux/ar71xx/base-files
parent6ae71708c9ced26961f73286d794e1aafedd6c52 (diff)
downloadupstream-c198ca682c187e61730119134e1dde75da2e7a16.tar.gz
upstream-c198ca682c187e61730119134e1dde75da2e7a16.tar.bz2
upstream-c198ca682c187e61730119134e1dde75da2e7a16.zip
ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ar71xx/base-files')
-rwxr-xr-xtarget/linux/ar71xx/base-files/etc/board.d/01_leds6
-rwxr-xr-xtarget/linux/ar71xx/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ar71xx/base-files/etc/diag.sh4
-rw-r--r--target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata4
-rwxr-xr-xtarget/linux/ar71xx/base-files/lib/ar71xx.sh6
-rwxr-xr-xtarget/linux/ar71xx/base-files/lib/upgrade/platform.sh4
6 files changed, 24 insertions, 4 deletions
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index a93ea1d578..38e665fb64 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -444,6 +444,9 @@ som9331)
ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt"
ucidef_set_led_usbdev "usb" "USB" "$board:green:system" "1-1"
;;
+sr3200)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
+ ;;
tellstick-znet-lite)
ucidef_set_led_netdev "lan_act" "LANACT" "tellstick:green:lan" "eth0" "tx rx"
ucidef_set_led_netdev "lan_link" "LANLINK" "tellstick:orange:lan" "eth0" "link"
@@ -738,6 +741,9 @@ wzr-hp-g300nh)
ucidef_set_led_netdev "router" "Router" "buffalo:green:router" "eth1"
ucidef_set_led_usbdev "usb" "USB" "buffalo:blue:usb" "1-1"
;;
+xd3200)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:blue:wlan2g" "phy1tpt"
+ ;;
z1)
ucidef_set_led_netdev "wlan1" "WLAN1" "$board:blue:tricolor0" "wlan1"
;;
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 949f161c9c..57d690d60c 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -230,6 +230,7 @@ ar71xx_setup_interfaces()
dir-835-a1|\
esr900|\
mynet-n750|\
+ sr3200|\
wndr3700v4|\
wndr4300)
ucidef_add_switch "switch0" \
@@ -395,7 +396,8 @@ ar71xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:wan"
;;
- unifiac-pro)
+ unifiac-pro|\
+ xd3200)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 9b9aea8a77..43ea2b683e 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -18,7 +18,9 @@ get_status_led() {
antminer-s3|\
antminer-r1|\
minibox-v1|\
- som9331)
+ som9331|\
+ sr3200|\
+ xd3200)
status_led="$board:green:system"
;;
ap132|\
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 7983dad80c..97875bd79a 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -49,7 +49,9 @@ case "$FIRMWARE" in
case $board in
cf-e380ac-v1|\
cf-e380ac-v2|\
- dlan-pro-1200-ac)
+ dlan-pro-1200-ac|\
+ sr3200|\
+ xd3200)
ath10kcal_extract "art" 20480 2116
;;
dap-2695-a1)
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 526d03344b..c27cd136b0 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -905,6 +905,9 @@ ar71xx_board_detect() {
*SOM9331)
name="som9331"
;;
+ *SR3200)
+ name="sr3200"
+ ;;
*TEW-632BRP)
name="tew-632brp"
;;
@@ -1190,6 +1193,9 @@ ar71xx_board_detect() {
*WHR-HP-G300N)
name="whr-hp-g300n"
;;
+ *XD3200)
+ name="xd3200"
+ ;;
*Z1)
name="z1"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 5f4375da6a..7b59bf3a55 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -228,6 +228,7 @@ platform_check_image() {
rocket-m-xw|\
rocket-m|\
rw2458n|\
+ sr3200|\
tew-632brp|\
tew-712br|\
tew-732br|\
@@ -251,7 +252,8 @@ platform_check_image() {
wzr-hp-ag300h|\
wzr-hp-g300nh2|\
wzr-hp-g300nh|\
- wzr-hp-g450h)
+ wzr-hp-g450h|\
+ xd3200)
[ "$magic" != "2705" ] && {
echo "Invalid image type."
return 1