aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: move partitions into partion table nodeJohn Crispin2016-06-191-25/+31
| | | | | | | | | | Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Mathias Kresin <openwrt@kresin.me> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49280 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: remove read-only flag on two partitions on BTHOMEHUBV3AJohn Crispin2016-04-261-2/+0
| | | | | | | | | | | Remove read-only flag on two partitions on BTHOMEHUBV3A: uboot-config - otherwise fw_setenv command cannot be used. ath9k-cal - so that ath9k calibration data can be copied to the partition on a newly installed board. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49250 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: use devicename:colour:function led naming schemeJohn Crispin2016-01-011-9/+9
| | | | | | | | | | | | | | | | The leds of the following boards are not renamed due to lack of manuals/informations: - ARV7519PW - ARV7510PW22 - ARV4510PW The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't match the leds from the manual or pictures (e.g. there shouldn't be a wps led). Signed-off-by: Mathias Kresin <openwrt@kresin.me> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48042 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add support for indicating the boot state using three ledsJohn Crispin2016-01-011-4/+8
| | | | | | | | | | | | | | The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48041 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: define default leds in dts filesJohn Crispin2016-01-011-3/+8
| | | | | | | | | | - ARV7525PW: use the power led as dsl led as done by the stock firmware - FRITZ3370: use the info led as internet led - FRITZ7320: use the power led as dsl led as done by the stock firmware Signed-off-by: Mathias Kresin <openwrt@kresin.me> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48037 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: BT Home Hub3A - device treeJohn Crispin2015-01-081-0/+210
BT Home Hub3A - device tree Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43877 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-13 02:19:14 +0000