Clean up the driver directory structure by moving all board specific files into the boards sub-structure.

2 files changed, 181 insertions, 0 deletions

diff --git a/boards/addons/tdisp/HD44780/tdisp_lld_board_olimex_e407.h b/boards/addons/tdisp/HD44780/tdisp_lld_board_olimex_e407.h
new file mode 100644
index 00000000..12407356
--- /dev/null
+++ b/boards/addons/tdisp/HD44780/tdisp_lld_board_olimex_e407.h
@@ -0,0 +1,59 @@
+/*
+ * This file is subject to the terms of the GFX License. If a copy of
+ * the license was not distributed with this file, you can obtain one at:
+ *
+ *              http://ugfx.org/license.html
+ */
+
+/**
+ * @file    drivers/tdisp/HD44780/tdisp_lld_board_olimex_e407.h
+ * @brief   TDISP driver subsystem board interface for the HD44780 display
+ *
+ * @addtogroup TDISP
+ * @{
+ */
+
+#ifndef _TDISP_LLD_BOARD_H
+#define _TDISP_LLD_BOARD_H
+
+/* Configure these to match the hardware connections on your board */
+#define BUS_4BITS	FALSE
+#define PORT_DATA	GPIOG
+#define PORT_CTRL	GPIOE
+#define PIN_RS		0
+#define PIN_RW		1
+#define PIN_EN		2
+
+static void init_board(void) {
+	palSetGroupMode(PORT_CTRL, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
+	palSetGroupMode(PORT_DATA, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
+	palClearPad(PORT_CTRL, PIN_RW);
+}
+
+static void writeToLCD(uint8_t data) {
+	palWritePort(PORT_DATA, data);
+	palSetPad(PORT_CTRL, PIN_EN);
+	gfxSleepMicroseconds(1);
+	palClearPad(PORT_CTRL, PIN_EN);
+	gfxSleepMicroseconds(5);
+}
+
+static void write_cmd(uint8_t data) {
+	palClearPad(PORT_CTRL, PIN_RS);
+	#if BUS_4BITS
+		writeToLCD(data>>4);
+	#endif
+	writeToLCD(data);
+}
+
+static void write_data(uint8_t data) {
+	palSetPad(PORT_CTRL, PIN_RS);
+	#if BUS_4BITS
+		writeToLCD(data>>4);
+	#endif
+	writeToLCD(data);
+}
+
+#endif /* _TDISP_LLD_BOARD_H */
+/** @} */
+
diff --git a/boards/addons/tdisp/HD44780/tdisp_lld_board_st_stm32f4_discovery.h b/boards/addons/tdisp/HD44780/tdisp_lld_board_st_stm32f4_discovery.h
new file mode 100644
index 00000000..43e161f1
--- /dev/null
+++ b/boards/addons/tdisp/HD44780/tdisp_lld_board_st_stm32f4_discovery.h
@@ -0,0 +1,122 @@
+/*
+ * This file is subject to the terms of the GFX License. If a copy of
+ * the license was not distributed with this file, you can obtain one at:
+ *
+ *              http://ugfx.org/license.html
+ */
+
+/**
+ * @file    drivers/tdisp/HD44780/tdisp_lld_board_st_stm32f4_discovery.h
+ * @brief   TDISP driver subsystem board interface for the HD44780 display
+ *
+ * @addtogroup TDISP
+ * @{
+ */
+
+#ifndef _TDISP_LLD_BOARD_H
+#define _TDISP_LLD_BOARD_H
+
+/* Configure these to match the hardware connections on your board */
+#define BUS_4BITS	TRUE
+
+/* Configure the bitoffset in the dataport so they match with the
+ * hardware pins. An offset of 0 means bit0 stays at bit0 of the dataport.
+ * If the offset is set to 3, bit0 of the nibble will be positioned at
+ * P[A..G]3 of the hardware-port.
+ */
+#define hardware_offset	3
+
+/* The port where the data is sent to. In the
+ * low-leveldriver het hardware_offset is taken
+ * into account. If for example the hardware_offset
+ * is set to 3, then de data will be sent to
+ * PE3, PE4, PE5 en PE6, if the dataport where GPIOE.
+ */
+#define PORT_DATA	GPIOE
+
+/* The port used to controle the controle lines of
+ * the display.
+ */
+#define PORT_CTRL	GPIOD
+/* Pin to controle the R/S-line of the display */
+#define PIN_RS		0
+/* Pin to controle the EN-line of the display */
+#define PIN_EN		1
+/* Pin to controle the R/W-pin of the display.
+ * If reading of the display is not used disable
+ * reading in the gfxconf.h and put a dummy value here
+ * as it will not be used.
+ */
+#define PIN_RW		7
+
+
+static void init_board(void) {
+	/* Initialize the ports for data and controle-lines */
+	palSetGroupMode(PORT_CTRL, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
+	palSetGroupMode(PORT_DATA, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
+	/* Set alle controle pins to low */
+	palClearPad(PORT_CTRL, PIN_RS);
+	palClearPad(PORT_CTRL, PIN_EN);
+	#if TDISP_NEED_READ
+	  palClearPad(PORT_CTRL, PIN_RW);
+	#endif
+}
+
+/* This is the low-level routine for sending the bits
+ * to the LCD-display. This routine shifts
+ * the bits so they match the hardware port.
+ */
+static void writeToLCD(uint8_t data) {
+	palWritePort(PORT_DATA, data<<hardware_offset);
+	palSetPad(PORT_CTRL, PIN_EN);
+	gfxSleepMicroseconds(1);
+	palClearPad(PORT_CTRL, PIN_EN);
+	/* wait a little while so that de display can process the data */
+	gfxSleepMicroseconds(5);
+}
+
+/* Writes a command to the display. The
+ * RS-line is pulled low and than the
+ * data is send.
+ */
+static void write_cmd(uint8_t data) {
+	palClearPad(PORT_CTRL, PIN_RS);
+	#if BUS_4BITS
+		/* first send the high-nibble */
+		writeToLCD(data>>4);
+	#endif
+	/* send the low-nibble */
+	#if BUS_4BITS
+		/* in 4-bit mode the high-nibble is zeroed out */
+		writeToLCD(data & 0x0F);
+	#else
+		writeToLCD(data);
+	#endif
+}
+
+// static void write_initcmd(uint8_t data) {
+//   write_cmd(data);
+// }
+
+/* Write data to the display. The
+ * RS-line is pulled high and than the
+ * data is send.
+ */
+static void write_data(uint8_t data) {
+	palSetPad(PORT_CTRL, PIN_RS);
+	#if BUS_4BITS
+		/* first send the high-nibble */
+		writeToLCD(data>>4);
+	#endif
+	/* send the low-nibble */
+	#if BUS_4BITS
+		/* in 4-bit mode the high-nibble is zeroed out */
+		writeToLCD(data & 0x0F);
+	#else
+		writeToLCD(data);
+	#endif
+}
+
+#endif /* _TDISP_LLD_BOARD_H */
+/** @} */
+