diff options
Diffstat (limited to 'os/hal/boards/NONSTANDARD_STM32F4_BARTHESS1/board.h')
-rw-r--r-- | os/hal/boards/NONSTANDARD_STM32F4_BARTHESS1/board.h | 520 |
1 files changed, 520 insertions, 0 deletions
diff --git a/os/hal/boards/NONSTANDARD_STM32F4_BARTHESS1/board.h b/os/hal/boards/NONSTANDARD_STM32F4_BARTHESS1/board.h new file mode 100644 index 000000000..a51044f61 --- /dev/null +++ b/os/hal/boards/NONSTANDARD_STM32F4_BARTHESS1/board.h @@ -0,0 +1,520 @@ +/*
+ ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for STMicroelectronics STM32F4-Discovery board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_NONSTANDARD_STM32F4_BARTHESS1
+#define BOARD_NAME "Hand made STM32F4x board"
+
+/*
+ * Board frequencies.
+ * NOTE: The LSE crystal is not fitted by default on the board.
+ */
+#define STM32_LSECLK 32768
+#define STM32_HSECLK 8000000
+
+/*
+ * Board voltages.
+ * Required for performance limits calculation.
+ */
+#define STM32_VDD 300
+
+/*
+ * MCU type as defined in the ST header.
+ */
+#define STM32F40_41xxx
+
+/*
+ * IO pins assignments.
+ */
+#define GPIOA_USART2_CTS 0 /* xbee */
+#define GPIOA_USART2_RTS 1 /* xbee */
+#define GPIOA_USART2_TX 2 /* xbee */
+#define GPIOA_USART2_RX 3 /* xbee */
+#define GPIOA_SPI1_NSS 4
+#define GPIOA_SPI1_SCK 5
+#define GPIOA_SPI1_MISO 6
+#define GPIOA_SPI1_MOSI 7
+#define GPIOA_5V_DOMAIN_EN 8
+#define GPIOA_USART1_TX 9 /* gps */
+#define GPIOA_USART1_RX 10/* gps */
+#define GPIOA_OTG_FS_DM 11
+#define GPIOA_OTG_FS_DP 12
+#define GPIOA_JTMS 13
+#define GPIOA_JTCK 14
+#define GPIOA_JTDI 15
+
+#define GPIOB_RECEIVER_PPM 0
+#define GPIOB_TACHOMETER 1
+#define GPIOB_BOOT1 2
+#define GPIOB_JTDO 3
+#define GPIOB_NJTRST 4
+#define GPIOB_LED_R 6
+#define GPIOB_LED_G 7
+#define GPIOB_LED_B 8
+#define GPIOB_I2C2_SCL 10
+#define GPIOB_I2C2_SDA 11
+
+
+#define GPIOC_AN_CURRENT_SENS 0
+#define GPIOC_AN_SUPPLY_SENS 1
+#define GPIOC_AN_6V_SENS 2
+#define GPIOC_AN33_0 3
+#define GPIOC_AN33_1 4
+#define GPIOC_AN33_2 5
+#define GPIOC_SDIO_D0 8
+#define GPIOC_SDIO_D1 9
+#define GPIOC_SDIO_D2 10
+#define GPIOC_SDIO_D3 11
+#define GPIOC_SDIO_CK 12
+#define GPIOC_TAMPER_RTC 13
+#define GPIOC_OSC32_IN 14
+#define GPIOC_OSC32_OUT 15
+
+#define GPIOD_SDIO_CMD 2
+#define GPIOD_PWM1 12
+#define GPIOD_PWM2 13
+#define GPIOD_PWM3 14
+#define GPIOD_PWM4 15
+
+#define GPIOE_GPS_PPS 0
+#define GPIOE_XBEE_SLEEP 1
+#define GPIOE_XBEE_RESET 2
+#define GPIOE_SDIO_DETECT 3
+#define GPIOE_USB_DISCOVERY 4
+#define GPIOE_GPS_PWR_EN 5
+#define GPIOE_BMP085_EOC 6
+#define GPIOE_MAG_INT 7
+#define GPIOE_MMA8451_INT1 8
+#define GPIOE_PWM5 9
+#define GPIOE_ITG3200_INT 10
+#define GPIOE_PWM6 11
+#define GPIOE_PWM7 13
+#define GPIOE_PWM8 14
+#define GPIOE_MMA8451_INT2 15
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ * Please refer to the STM32 Reference Manual for details.
+ *
+ * 1 for open drain outputs denotes hi-Z state
+ */
+#define PIN_MODE_INPUT(n) (0U << ((n) * 2))
+#define PIN_MODE_OUTPUT(n) (1U << ((n) * 2))
+#define PIN_MODE_ALTERNATE(n) (2U << ((n) * 2))
+#define PIN_MODE_ANALOG(n) (3U << ((n) * 2))
+#define PIN_OTYPE_PUSHPULL(n) (0U << (n))
+#define PIN_OTYPE_OPENDRAIN(n) (1U << (n))
+#define PIN_OSPEED_2M(n) (0U << ((n) * 2))
+#define PIN_OSPEED_25M(n) (1U << ((n) * 2))
+#define PIN_OSPEED_50M(n) (2U << ((n) * 2))
+#define PIN_OSPEED_100M(n) (3U << ((n) * 2))
+#define PIN_PUDR_FLOATING(n) (0U << ((n) * 2))
+#define PIN_PUDR_PULLUP(n) (1U << ((n) * 2))
+#define PIN_PUDR_PULLDOWN(n) (2U << ((n) * 2))
+#define PIN_AFIO_AF(n, v) ((v##U) << ((n % 8) * 4))
+
+/*
+ * Port A setup.
+ * All input with pull-up except:
+#define GPIOA_USART2_CTS 0 //xbee
+#define GPIOA_USART2_RTS 1 //xbee
+#define GPIOA_USART2_TX 2 //xbee
+#define GPIOA_USART2_Rx 3 //xbee
+#define GPIOA_SPI1_NSS 4
+#define GPIOA_SPI1_SCK 5
+#define GPIOA_SPI1_MISO 6
+#define GPIOA_SPI1_MOSI 7
+#define GPIOA_5V_DOMAIN_EN 8
+#define GPIOA_USART1_TX 9
+#define GPIOA_USART1_RX 10
+#define GPIOA_OTG_FS_DM 11
+#define GPIOA_OTG_FS_DP 12
+#define GPIOA_JTMS 13
+#define GPIOA_JTCK 14
+#define GPIOA_JTDI 15
+ */
+
+/* default after reset 0xA8000000 */
+#define VAL_GPIOA_MODER (PIN_MODE_ALTERNATE(GPIOA_USART2_CTS) | \
+ PIN_MODE_ALTERNATE(GPIOA_USART2_RTS) | \
+ PIN_MODE_ALTERNATE(GPIOA_USART2_TX) | \
+ PIN_MODE_ALTERNATE(GPIOA_USART2_RX) | \
+ PIN_MODE_ALTERNATE(GPIOA_SPI1_NSS) | \
+ PIN_MODE_ALTERNATE(GPIOA_SPI1_SCK) | \
+ PIN_MODE_ALTERNATE(GPIOA_SPI1_MISO) | \
+ PIN_MODE_ALTERNATE(GPIOA_SPI1_MOSI) | \
+ PIN_MODE_OUTPUT(GPIOA_5V_DOMAIN_EN) | \
+ PIN_MODE_ALTERNATE(GPIOA_USART1_TX) | \
+ PIN_MODE_ALTERNATE(GPIOA_USART1_RX) | \
+ PIN_MODE_ALTERNATE(GPIOA_OTG_FS_DM) | \
+ PIN_MODE_ALTERNATE(GPIOA_OTG_FS_DP) | \
+ PIN_MODE_ALTERNATE(GPIOA_JTMS) | \
+ PIN_MODE_ALTERNATE(GPIOA_JTCK) | \
+ PIN_MODE_ALTERNATE(GPIOA_JTDI))
+/* default 0x00000000 */
+#define VAL_GPIOA_OTYPER 0x00000000
+/* default 0x00000000 */
+#define VAL_GPIOA_OSPEEDR 0x00000000
+/* 0x64000000 */
+#define VAL_GPIOA_PUPDR (PIN_PUDR_FLOATING(GPIOA_USART2_CTS) | \
+ PIN_PUDR_FLOATING(GPIOA_USART2_RTS) | \
+ PIN_PUDR_FLOATING(GPIOA_USART2_TX) | \
+ PIN_PUDR_FLOATING(GPIOA_USART2_RX) | \
+ PIN_PUDR_PULLUP(GPIOA_SPI1_NSS) | \
+ PIN_PUDR_PULLUP(GPIOA_SPI1_SCK) | \
+ PIN_PUDR_PULLUP(GPIOA_SPI1_MISO) | \
+ PIN_PUDR_PULLUP(GPIOA_SPI1_MOSI) | \
+ PIN_PUDR_FLOATING(GPIOA_5V_DOMAIN_EN) | \
+ PIN_PUDR_FLOATING(GPIOA_USART1_TX) | \
+ PIN_PUDR_FLOATING(GPIOA_USART1_RX) | \
+ PIN_PUDR_FLOATING(GPIOA_OTG_FS_DM) | \
+ PIN_PUDR_FLOATING(GPIOA_OTG_FS_DP) | \
+ PIN_PUDR_PULLUP(GPIOA_JTMS) | \
+ PIN_PUDR_PULLDOWN(GPIOA_JTCK) | \
+ PIN_PUDR_PULLUP(GPIOA_JTDI))
+/* 0x00000000 */
+#define VAL_GPIOA_ODR 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOA_AFRL (PIN_AFIO_AF(GPIOA_USART2_CTS, 7) | \
+ PIN_AFIO_AF(GPIOA_USART2_RTS, 7) | \
+ PIN_AFIO_AF(GPIOA_USART2_TX, 7) | \
+ PIN_AFIO_AF(GPIOA_USART2_RX, 7)| \
+ PIN_AFIO_AF(GPIOA_SPI1_NSS, 5) | \
+ PIN_AFIO_AF(GPIOA_SPI1_SCK, 5) | \
+ PIN_AFIO_AF(GPIOA_SPI1_MISO, 5) | \
+ PIN_AFIO_AF(GPIOA_SPI1_MOSI, 5))
+/* 0x00000000 */
+#define VAL_GPIOA_AFRH (PIN_AFIO_AF(GPIOA_USART1_TX, 7) | \
+ PIN_AFIO_AF(GPIOA_USART1_RX, 7) | \
+ PIN_AFIO_AF(GPIOA_OTG_FS_DM, 10) | \
+ PIN_AFIO_AF(GPIOA_OTG_FS_DP, 10) | \
+ PIN_AFIO_AF(GPIOA_JTMS, 0) | \
+ PIN_AFIO_AF(GPIOA_JTCK, 0) | \
+ PIN_AFIO_AF(GPIOA_JTDI, 0))
+
+/*
+ * Port B setup.
+#define GPIOB_RECEIVER_PPM 0
+#define GPIOB_TACHOMETER 1
+#define GPIOB_BOOT1 2
+#define GPIOB_JTDO 3
+#define GPIOB_NJTRST 4
+#define GPIOB_LED_R 6
+#define GPIOB_LED_G 7
+#define GPIOB_LED_B 8
+#define GPIOB_I2C2_SCL 10
+#define GPIOB_I2C2_SDA 11
+ */
+/* 0x00000280 */
+#define VAL_GPIOB_MODER (PIN_MODE_INPUT(GPIOB_RECEIVER_PPM) | \
+ PIN_MODE_INPUT(GPIOB_TACHOMETER) | \
+ PIN_MODE_INPUT(GPIOB_BOOT1) | \
+ PIN_MODE_ALTERNATE(GPIOB_JTDO) | \
+ PIN_MODE_ALTERNATE(GPIOB_NJTRST) | \
+ PIN_MODE_INPUT(5) | \
+ PIN_MODE_OUTPUT(GPIOB_LED_R) | \
+ PIN_MODE_OUTPUT(GPIOB_LED_G) | \
+ PIN_MODE_OUTPUT(GPIOB_LED_B) | \
+ PIN_MODE_INPUT(9) | \
+ PIN_MODE_ALTERNATE(GPIOB_I2C2_SCL) | \
+ PIN_MODE_ALTERNATE(GPIOB_I2C2_SDA) | \
+ PIN_MODE_INPUT(12) | \
+ PIN_MODE_INPUT(13) | \
+ PIN_MODE_INPUT(14) | \
+ PIN_MODE_INPUT(15))
+/* 0x00000000 */
+#define VAL_GPIOB_OTYPER (PIN_OTYPE_OPENDRAIN(GPIOB_LED_R) | \
+ PIN_OTYPE_OPENDRAIN(GPIOB_LED_G) | \
+ PIN_OTYPE_OPENDRAIN(GPIOB_LED_B) | \
+ PIN_OTYPE_OPENDRAIN(GPIOB_I2C2_SCL) | \
+ PIN_OTYPE_OPENDRAIN(GPIOB_I2C2_SDA))
+/* 0x000000C0 */
+#define VAL_GPIOB_OSPEEDR 0x000000C0//0xAAAAAAEA
+/* 0x00000100 */
+#define VAL_GPIOB_PUPDR (PIN_PUDR_PULLDOWN(GPIOB_RECEIVER_PPM) | \
+ PIN_PUDR_PULLDOWN(GPIOB_TACHOMETER) | \
+ PIN_PUDR_FLOATING(GPIOB_BOOT1) | \
+ PIN_PUDR_FLOATING(GPIOB_JTDO) | \
+ PIN_PUDR_PULLUP(GPIOB_NJTRST) | \
+ PIN_PUDR_FLOATING(5) | \
+ PIN_PUDR_FLOATING(GPIOB_LED_R) | \
+ PIN_PUDR_FLOATING(GPIOB_LED_G) | \
+ PIN_PUDR_FLOATING(GPIOB_LED_B) | \
+ PIN_PUDR_FLOATING(9) | \
+ PIN_PUDR_FLOATING(GPIOB_I2C2_SCL) | \
+ PIN_PUDR_FLOATING(GPIOB_I2C2_SDA) | \
+ PIN_PUDR_PULLUP(12) | \
+ PIN_PUDR_PULLUP(13) | \
+ PIN_PUDR_PULLUP(14) | \
+ PIN_PUDR_PULLUP(15))
+/* 0x00000000 */
+#define VAL_GPIOB_ODR 0x000001C0
+/* 0x00000000 */
+#define VAL_GPIOB_AFRL (PIN_AFIO_AF(GPIOB_RECEIVER_PPM, 0) | \
+ PIN_AFIO_AF(GPIOB_JTDO, 0))
+/* 0x00000000 */
+#define VAL_GPIOB_AFRH (PIN_AFIO_AF(GPIOB_I2C2_SCL, 4) | \
+ PIN_AFIO_AF(GPIOB_I2C2_SDA, 4))
+
+
+/*
+ * Port C setup.
+#define GPIOC_AN_CURRENT_SENS 0
+#define GPIOC_AN_SUPPLY_SENS 1
+#define GPIOC_AN_6V_SENS 2
+#define GPIOC_AN33_0 3
+#define GPIOC_AN33_1 4
+#define GPIOC_AN33_2 5
+
+#define GPIOC_SDIO_D0 8
+#define GPIOC_SDIO_D1 9
+#define GPIOC_SDIO_D2 10
+#define GPIOC_SDIO_D3 11
+#define GPIOC_SDIO_CK 12
+
+#define GPIOC_TAMPER_RTC 13
+#define GPIOC_OSC32_IN 14
+#define GPIOC_OSC32_OUT 15
+ */
+/* 0x00000000 */
+#define VAL_GPIOC_MODER (PIN_MODE_ANALOG(GPIOC_AN_CURRENT_SENS) | \
+ PIN_MODE_ANALOG(GPIOC_AN_SUPPLY_SENS) | \
+ PIN_MODE_ANALOG(GPIOC_AN_6V_SENS) | \
+ PIN_MODE_ANALOG(GPIOC_AN33_0) | \
+ PIN_MODE_ANALOG(GPIOC_AN33_1) | \
+ PIN_MODE_ANALOG(GPIOC_AN33_2) | \
+ PIN_MODE_INPUT(6) | \
+ PIN_MODE_INPUT(7) | \
+ PIN_MODE_ALTERNATE(GPIOC_SDIO_D0) | \
+ PIN_MODE_ALTERNATE(GPIOC_SDIO_D1) | \
+ PIN_MODE_ALTERNATE(GPIOC_SDIO_D2) | \
+ PIN_MODE_ALTERNATE(GPIOC_SDIO_D3) | \
+ PIN_MODE_ALTERNATE(GPIOC_SDIO_CK) | \
+ PIN_MODE_INPUT(GPIOC_TAMPER_RTC) | \
+ PIN_MODE_INPUT(GPIOC_OSC32_IN) | \
+ PIN_MODE_INPUT(GPIOC_OSC32_OUT))
+
+/* 0x00000000 */
+#define VAL_GPIOC_OTYPER 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOC_OSPEEDR (PIN_OSPEED_25M(GPIOC_SDIO_D0) | \
+ PIN_OSPEED_25M(GPIOC_SDIO_D1) | \
+ PIN_OSPEED_25M(GPIOC_SDIO_D2) | \
+ PIN_OSPEED_25M(GPIOC_SDIO_D3) | \
+ PIN_OSPEED_25M(GPIOC_SDIO_CK) | \
+ PIN_OSPEED_2M(GPIOC_TAMPER_RTC))
+/* 0x00000000 */
+#define VAL_GPIOC_PUPDR (PIN_PUDR_FLOATING(GPIOC_AN_CURRENT_SENS) | \
+ PIN_PUDR_FLOATING(GPIOC_AN_SUPPLY_SENS) | \
+ PIN_PUDR_FLOATING(GPIOC_AN_6V_SENS) | \
+ PIN_PUDR_FLOATING(GPIOC_AN33_0) | \
+ PIN_PUDR_FLOATING(GPIOC_AN33_1) | \
+ PIN_PUDR_FLOATING(GPIOC_AN33_2) | \
+ PIN_PUDR_PULLUP(6) | \
+ PIN_PUDR_PULLUP(7) | \
+ PIN_PUDR_PULLUP(GPIOC_SDIO_D0) | \
+ PIN_PUDR_PULLUP(GPIOC_SDIO_D1) | \
+ PIN_PUDR_PULLUP(GPIOC_SDIO_D2) | \
+ PIN_PUDR_PULLUP(GPIOC_SDIO_D3) | \
+ PIN_PUDR_PULLUP(GPIOC_SDIO_CK) | \
+ PIN_PUDR_FLOATING(GPIOC_TAMPER_RTC) | \
+ PIN_PUDR_FLOATING(GPIOC_OSC32_IN) | \
+ PIN_PUDR_FLOATING(GPIOC_OSC32_OUT))
+/* 0x00000000 */
+#define VAL_GPIOC_ODR 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOC_AFRL 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOC_AFRH (PIN_AFIO_AF(GPIOC_SDIO_D0, 12) | \
+ PIN_AFIO_AF(GPIOC_SDIO_D1, 12) | \
+ PIN_AFIO_AF(GPIOC_SDIO_D2, 12) | \
+ PIN_AFIO_AF(GPIOC_SDIO_D3, 12) | \
+ PIN_AFIO_AF(GPIOC_SDIO_CK, 12))
+
+/*
+ * Port D setup.
+#define GPIOD_SDIO_CMD 2
+#define GPIOD_PWM1 12
+#define GPIOD_PWM2 13
+#define GPIOD_PWM3 14
+#define GPIOD_PWM4 15
+ */
+/* 0x00000000 */
+#define VAL_GPIOD_MODER (PIN_MODE_ALTERNATE(GPIOD_SDIO_CMD) | \
+ PIN_MODE_ALTERNATE(GPIOD_PWM1) | \
+ PIN_MODE_ALTERNATE(GPIOD_PWM2) | \
+ PIN_MODE_ALTERNATE(GPIOD_PWM3) | \
+ PIN_MODE_ALTERNATE(GPIOD_PWM4))
+/* 0x00000000 */
+#define VAL_GPIOD_OTYPER 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOD_OSPEEDR (PIN_OSPEED_25M(GPIOD_SDIO_CMD))
+/* 0x00000000 */
+#define VAL_GPIOD_PUPDR (PIN_PUDR_PULLUP(GPIOD_SDIO_CMD) | \
+ PIN_PUDR_PULLDOWN(GPIOD_PWM1) | \
+ PIN_PUDR_PULLDOWN(GPIOD_PWM2) | \
+ PIN_PUDR_PULLDOWN(GPIOD_PWM3) | \
+ PIN_PUDR_PULLDOWN(GPIOD_PWM4))
+/* 0x00000000 */
+#define VAL_GPIOD_ODR 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOD_AFRL (PIN_AFIO_AF(GPIOD_SDIO_CMD, 12))
+/* 0x00000000 */
+#define VAL_GPIOD_AFRH (PIN_AFIO_AF(GPIOD_PWM1, 2) | \
+ PIN_AFIO_AF(GPIOD_PWM2, 2) | \
+ PIN_AFIO_AF(GPIOD_PWM3, 2) | \
+ PIN_AFIO_AF(GPIOD_PWM4, 2))
+
+
+/*
+ * Port E setup.
+#define GPIOE_GPS_PPS 0
+#define GPIOE_XBEE_SLEEP 1
+#define GPIOE_XBEE_RESET 2
+#define GPIOE_SDIO_DETECT 3
+#define GPIOE_USB_DISCOVERY 4
+#define GPIOE_GPS_EN 5
+#define GPIOE_BMP085_EOC 6
+#define GPIOE_MAG_INT 7
+#define GPIOE_MMA8451_INT1 8
+#define GPIOE_PWM5 9
+#define GPIOE_ITG3200_INT 10
+#define GPIOE_PWM6 11
+#define GPIOE_TACHOMETER 12
+#define GPIOE_PWM7 13
+#define GPIOE_PWM8 14
+#define GPIOE_MMA8451_INT2 15
+ */
+/* 0x00000000 */
+#define VAL_GPIOE_MODER (PIN_MODE_INPUT(GPIOE_GPS_PPS) | \
+ PIN_MODE_OUTPUT(GPIOE_XBEE_SLEEP) | \
+ PIN_MODE_OUTPUT(GPIOE_XBEE_RESET) | \
+ PIN_MODE_INPUT(GPIOE_SDIO_DETECT) | \
+ PIN_MODE_OUTPUT(GPIOE_USB_DISCOVERY) | \
+ PIN_MODE_OUTPUT(GPIOE_GPS_PWR_EN) | \
+ PIN_MODE_INPUT(GPIOE_BMP085_EOC) | \
+ PIN_MODE_INPUT(GPIOE_MAG_INT) | \
+ PIN_MODE_INPUT(GPIOE_MMA8451_INT1) | \
+ PIN_MODE_ALTERNATE(GPIOE_PWM5) | \
+ PIN_MODE_INPUT(GPIOE_ITG3200_INT) | \
+ PIN_MODE_ALTERNATE(GPIOE_PWM6) | \
+ PIN_MODE_INPUT(12) | \
+ PIN_MODE_ALTERNATE(GPIOE_PWM7) | \
+ PIN_MODE_ALTERNATE(GPIOE_PWM8) | \
+ PIN_MODE_INPUT(GPIOE_MMA8451_INT2))
+/* 0x00000000 */
+#define VAL_GPIOE_OTYPER (PIN_OTYPE_PUSHPULL(GPIOE_XBEE_SLEEP) | \
+ PIN_OTYPE_PUSHPULL(GPIOE_XBEE_RESET) | \
+ PIN_OTYPE_PUSHPULL(GPIOE_USB_DISCOVERY) | \
+ PIN_OTYPE_OPENDRAIN(GPIOE_GPS_PWR_EN) | \
+ PIN_OTYPE_PUSHPULL(GPIOE_PWM5) | \
+ PIN_OTYPE_PUSHPULL(GPIOE_PWM6) | \
+ PIN_OTYPE_PUSHPULL(GPIOE_PWM7) | \
+ PIN_OTYPE_PUSHPULL(GPIOE_PWM8))
+/* 0x00000000 */
+#define VAL_GPIOE_OSPEEDR 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOE_PUPDR (PIN_PUDR_PULLDOWN(GPIOE_GPS_PPS) | \
+ PIN_PUDR_PULLUP(GPIOE_XBEE_SLEEP) | \
+ PIN_PUDR_FLOATING(GPIOE_XBEE_RESET) | \
+ PIN_PUDR_PULLUP(GPIOE_SDIO_DETECT) | \
+ PIN_PUDR_FLOATING(GPIOE_USB_DISCOVERY) | \
+ PIN_PUDR_FLOATING(GPIOE_GPS_PWR_EN) | \
+ PIN_PUDR_PULLDOWN(GPIOE_BMP085_EOC) | \
+ PIN_PUDR_PULLDOWN(GPIOE_MAG_INT) | \
+ PIN_PUDR_PULLDOWN(GPIOE_MMA8451_INT1) | \
+ PIN_PUDR_PULLDOWN(GPIOE_PWM5) | \
+ PIN_PUDR_PULLDOWN(GPIOE_ITG3200_INT) | \
+ PIN_PUDR_PULLDOWN(GPIOE_PWM6) | \
+ PIN_PUDR_PULLUP(12) | \
+ PIN_PUDR_PULLDOWN(GPIOE_PWM7) | \
+ PIN_PUDR_PULLDOWN(GPIOE_PWM8) | \
+ PIN_PUDR_PULLDOWN(GPIOE_MMA8451_INT2))
+/* 0x00000000 */
+#define VAL_GPIOE_ODR 0x30
+/* 0x00000000 */
+#define VAL_GPIOE_AFRL 0x00000000
+/* 0x00000000 */
+#define VAL_GPIOE_AFRH (PIN_AFIO_AF(GPIOE_PWM5, 1) | \
+ PIN_AFIO_AF(GPIOE_PWM6, 1) | \
+ PIN_AFIO_AF(GPIOE_PWM7, 1) | \
+ PIN_AFIO_AF(GPIOE_PWM8, 1))
+
+/*
+ * Port F setup.
+ */
+#define VAL_GPIOF_MODER 0x00000000
+#define VAL_GPIOF_OTYPER 0x00000000
+#define VAL_GPIOF_OSPEEDR 0x00000000
+#define VAL_GPIOF_PUPDR 0x00000000
+#define VAL_GPIOF_ODR 0x00000000
+#define VAL_GPIOF_AFRL 0x00000000
+#define VAL_GPIOF_AFRH 0x00000000
+
+/*
+ * Port G setup.
+ */
+#define VAL_GPIOG_MODER 0x00000000
+#define VAL_GPIOG_OTYPER 0x00000000
+#define VAL_GPIOG_OSPEEDR 0x00000000
+#define VAL_GPIOG_PUPDR 0x00000000
+#define VAL_GPIOG_ODR 0x00000000
+#define VAL_GPIOG_AFRL 0x00000000
+#define VAL_GPIOG_AFRH 0x00000000
+
+/*
+ * Port H setup.
+ */
+#define VAL_GPIOH_MODER 0x00000000
+#define VAL_GPIOH_OTYPER 0x00000000
+#define VAL_GPIOH_OSPEEDR 0x00000000
+#define VAL_GPIOH_PUPDR 0x00000000
+#define VAL_GPIOH_ODR 0x00000000
+#define VAL_GPIOH_AFRL 0x00000000
+#define VAL_GPIOH_AFRH 0x00000000
+
+/*
+ * Port I setup.
+ */
+#define VAL_GPIOI_MODER 0x00000000
+#define VAL_GPIOI_OTYPER 0x00000000
+#define VAL_GPIOI_OSPEEDR 0x00000000
+#define VAL_GPIOI_PUPDR 0x00000000
+#define VAL_GPIOI_ODR 0x00000000
+#define VAL_GPIOI_AFRL 0x00000000
+#define VAL_GPIOI_AFRH 0x00000000
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+ void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
|