Add CRC Driver

This patch includes a high level and two low level drivers.

The high level driver is enabled with flag HAL_USE_CRC

The low level drivers include:
    * Hardware CRC for the STM32 cortex processor lines.(when supported)
        * Enabled with flag STM32_CRC_USE_CRC1
        * DMA is enabled with CRC_USE_DMA
          * SYNC api will use DMA, but put calling thread to sleep
          * ASYNC api enabled.
        * DMA Disabled
          * SYNC api spin while calculating CRC
          * ASYNC api disabled
    * Software CRC (3 modes)
        * CRCSW_CRC32_TABLE - Enables crc32 with lookup table.
        * CRCSW_CRC16_TABLE - Enables crc16 with lookup tables.
        * CRCSW_PROGRAMMBLE - Enables any crc done with computation.
          * Can calculate any crc configuration.
        * CRC_USE_DMA obviously not support with software CRC

1 files changed, 340 insertions, 0 deletions

diff --git a/testhal/STM32/STM32F0xx/crc/halconf.h b/testhal/STM32/STM32F0xx/crc/halconf.h
new file mode 100644
index 0000000..17118b0
--- /dev/null
+++ b/testhal/STM32/STM32F0xx/crc/halconf.h
@@ -0,0 +1,340 @@
+/*

+    ChibiOS - Copyright (C) 2015 Michael D. Spradling

+

+    Licensed under the Apache License, Version 2.0 (the "License");

+    you may not use this file except in compliance with the License.

+    You may obtain a copy of the License at

+

+        http://www.apache.org/licenses/LICENSE-2.0

+

+    Unless required by applicable law or agreed to in writing, software

+    distributed under the License is distributed on an "AS IS" BASIS,

+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

+    See the License for the specific language governing permissions and

+    limitations under the License.

+*/

+

+/**

+ * @file    templates/halconf.h

+ * @brief   HAL configuration header.

+ * @details HAL configuration file, this file allows to enable or disable the

+ *          various device drivers from your application. You may also use

+ *          this file in order to override the device drivers default settings.

+ *

+ * @addtogroup HAL_CONF

+ * @{

+ */

+

+#ifndef _HALCONF_H_

+#define _HALCONF_H_

+

+#include "mcuconf.h"

+

+/**

+ * @brief   Enables the PAL subsystem.

+ */

+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)

+#define HAL_USE_PAL                 TRUE

+#endif

+

+/**

+ * @brief   Enables the ADC subsystem.

+ */

+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)

+#define HAL_USE_ADC                 FALSE

+#endif

+

+/**

+ * @brief   Enables the CAN subsystem.

+ */

+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)

+#define HAL_USE_CAN                 FALSE

+#endif

+

+/**

+ * @brief   Enables the DAC subsystem.

+ */

+#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)

+#define HAL_USE_DAC                 FALSE

+#endif

+

+/**

+ * @brief   Enables the EXT subsystem.

+ */

+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)

+#define HAL_USE_EXT                 FALSE

+#endif

+

+/**

+ * @brief   Enables the GPT subsystem.

+ */

+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)

+#define HAL_USE_GPT                 FALSE

+#endif

+

+/**

+ * @brief   Enables the I2C subsystem.

+ */

+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)

+#define HAL_USE_I2C                 FALSE

+#endif

+

+/**

+ * @brief   Enables the I2S subsystem.

+ */

+#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)

+#define HAL_USE_I2S                 FALSE

+#endif

+

+/**

+ * @brief   Enables the ICU subsystem.

+ */

+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)

+#define HAL_USE_ICU                 FALSE

+#endif

+

+/**

+ * @brief   Enables the MAC subsystem.

+ */

+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)

+#define HAL_USE_MAC                 FALSE

+#endif

+

+/**

+ * @brief   Enables the MMC_SPI subsystem.

+ */

+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)

+#define HAL_USE_MMC_SPI             FALSE

+#endif

+

+/**

+ * @brief   Enables the PWM subsystem.

+ */

+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)

+#define HAL_USE_PWM                 FALSE

+#endif

+

+/**

+ * @brief   Enables the RTC subsystem.

+ */

+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)

+#define HAL_USE_RTC                 FALSE

+#endif

+

+/**

+ * @brief   Enables the SDC subsystem.

+ */

+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)

+#define HAL_USE_SDC                 FALSE

+#endif

+

+/**

+ * @brief   Enables the SERIAL subsystem.

+ */

+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)

+#define HAL_USE_SERIAL              FALSE

+#endif

+

+/**

+ * @brief   Enables the SERIAL over USB subsystem.

+ */

+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)

+#define HAL_USE_SERIAL_USB          FALSE

+#endif

+

+/**

+ * @brief   Enables the SPI subsystem.

+ */

+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)

+#define HAL_USE_SPI                 FALSE

+#endif

+

+/**

+ * @brief   Enables the UART subsystem.

+ */

+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)

+#define HAL_USE_UART                FALSE

+#endif

+

+/**

+ * @brief   Enables the USB subsystem.

+ */

+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)

+#define HAL_USE_USB                 FALSE

+#endif

+

+/*===========================================================================*/

+/* ADC driver related settings.                                              */

+/*===========================================================================*/

+

+/**

+ * @brief   Enables synchronous APIs.

+ * @note    Disabling this option saves both code and data space.

+ */

+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)

+#define ADC_USE_WAIT                TRUE

+#endif

+

+/**

+ * @brief   Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.

+ * @note    Disabling this option saves both code and data space.

+ */

+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)

+#define ADC_USE_MUTUAL_EXCLUSION    TRUE

+#endif

+

+/*===========================================================================*/

+/* CAN driver related settings.                                              */

+/*===========================================================================*/

+

+/**

+ * @brief   Sleep mode related APIs inclusion switch.

+ */

+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)

+#define CAN_USE_SLEEP_MODE          TRUE

+#endif

+

+/*===========================================================================*/

+/* I2C driver related settings.                                              */

+/*===========================================================================*/

+

+/**

+ * @brief   Enables the mutual exclusion APIs on the I2C bus.

+ */

+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)

+#define I2C_USE_MUTUAL_EXCLUSION    TRUE

+#endif

+

+/*===========================================================================*/

+/* MAC driver related settings.                                              */

+/*===========================================================================*/

+

+/**

+ * @brief   Enables an event sources for incoming packets.

+ */

+#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)

+#define MAC_USE_ZERO_COPY           FALSE

+#endif

+

+/**

+ * @brief   Enables an event sources for incoming packets.

+ */

+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)

+#define MAC_USE_EVENTS              TRUE

+#endif

+

+/*===========================================================================*/

+/* MMC_SPI driver related settings.                                          */

+/*===========================================================================*/

+

+/**

+ * @brief   Delays insertions.

+ * @details If enabled this options inserts delays into the MMC waiting

+ *          routines releasing some extra CPU time for the threads with

+ *          lower priority, this may slow down the driver a bit however.

+ *          This option is recommended also if the SPI driver does not

+ *          use a DMA channel and heavily loads the CPU.

+ */

+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)

+#define MMC_NICE_WAITING            TRUE

+#endif

+

+/*===========================================================================*/

+/* SDC driver related settings.                                              */

+/*===========================================================================*/

+

+/**

+ * @brief   Number of initialization attempts before rejecting the card.

+ * @note    Attempts are performed at 10mS intervals.

+ */

+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)

+#define SDC_INIT_RETRY              100

+#endif

+

+/**

+ * @brief   Include support for MMC cards.

+ * @note    MMC support is not yet implemented so this option must be kept

+ *          at @p FALSE.

+ */

+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)

+#define SDC_MMC_SUPPORT             FALSE

+#endif

+

+/**

+ * @brief   Delays insertions.

+ * @details If enabled this options inserts delays into the MMC waiting

+ *          routines releasing some extra CPU time for the threads with

+ *          lower priority, this may slow down the driver a bit however.

+ */

+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)

+#define SDC_NICE_WAITING            TRUE

+#endif

+

+/*===========================================================================*/

+/* SERIAL driver related settings.                                           */

+/*===========================================================================*/

+

+/**

+ * @brief   Default bit rate.

+ * @details Configuration parameter, this is the baud rate selected for the

+ *          default configuration.

+ */

+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)

+#define SERIAL_DEFAULT_BITRATE      38400

+#endif

+

+/**

+ * @brief   Serial buffers size.

+ * @details Configuration parameter, you can change the depth of the queue

+ *          buffers depending on the requirements of your application.

+ * @note    The default is 64 bytes for both the transmission and receive

+ *          buffers.

+ */

+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)

+#define SERIAL_BUFFERS_SIZE         16

+#endif

+

+/*===========================================================================*/

+/* SERIAL_USB driver related setting.                                        */

+/*===========================================================================*/

+

+/**

+ * @brief   Serial over USB buffers size.

+ * @details Configuration parameter, the buffer size must be a multiple of

+ *          the USB data endpoint maximum packet size.

+ * @note    The default is 64 bytes for both the transmission and receive

+ *          buffers.

+ */

+#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)

+#define SERIAL_USB_BUFFERS_SIZE     256

+#endif

+

+/*===========================================================================*/

+/* SPI driver related settings.                                              */

+/*===========================================================================*/

+

+/**

+ * @brief   Enables synchronous APIs.

+ * @note    Disabling this option saves both code and data space.

+ */

+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)

+#define SPI_USE_WAIT                TRUE

+#endif

+

+/**

+ * @brief   Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.

+ * @note    Disabling this option saves both code and data space.

+ */

+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)

+#define SPI_USE_MUTUAL_EXCLUSION    TRUE

+#endif

+

+/*===========================================================================*/

+/* Community drivers's includes                                              */

+/*===========================================================================*/

+

+#include "halconf_community.h"

+

+#endif /* _HALCONF_H_ */

+

+/** @} */