diff options
Diffstat (limited to 'roms/u-boot/doc/README.mpc85xxcds')
| -rw-r--r-- | roms/u-boot/doc/README.mpc85xxcds | 225 |
1 files changed, 225 insertions, 0 deletions
diff --git a/roms/u-boot/doc/README.mpc85xxcds b/roms/u-boot/doc/README.mpc85xxcds new file mode 100644 index 00000000..bc5db0ca --- /dev/null +++ b/roms/u-boot/doc/README.mpc85xxcds @@ -0,0 +1,225 @@ +Motorola MPC85xxCDS boards +-------------------------- + +The CDS family of boards consists of a PCI backplane called the +"Arcadia", a PCI-form-factor carrier card that plugs into a PCI slot, +and a CPU daughter card that bolts onto the daughter card. + +Much of the content of the README.mpc85xxads for the 85xx ADS boards +applies to the 85xx CDS boards as well. In particular the toolchain, +the switch nomenclature, and the basis for the memory map. There are +some differences, though. + + +Building U-Boot +--------------- + +The Binutils in current ELDK toolchain will not support MPC85xx +chip. You need to use binutils-2.14.tar.bz2 (or newer) from + http://ftp.gnu.org/gnu/binutils. + +The 85xx CDS code base is known to compile using: + gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a) + + +Memory Map +---------- + +The memory map for u-boot and linux has been extended w.r.t. the ADS +platform to allow for utilization of all 85xx CDS devices. The memory +map is setup for linux to operate properly. The linux source when +configured for MPC85xx CDS has been updated to reflect the new memory +map. + +The mapping is: + + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x9fff_ffff PCI1 MEM 512M + 0xa000_0000 0xbfff_ffff PCI2 MEM 512M + 0xe000_0000 0xe00f_ffff CCSR 1M + 0xe200_0000 0xe2ff_ffff PCI1 IO 16M + 0xe300_0000 0xe3ff_ffff PCI2 IO 16M + 0xf000_0000 0xf7ff_ffff SDRAM 128M + 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M + 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M + 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M + + (*) The system control registers (CADMUS) start at offset 0xfdb0_4000 + within the NVRAM/CADMUS region of memory. + + +Using Flash +----------- + +The CDS board has two flash banks, each 8MB in size (2^23 = 0x00800000). +There is a switch which allows the boot-bank to be selected. The switch +settings for updating flash are given below. + +The u-boot commands for copying the boot-bank into the secondary bank are +as follows: + + erase ff780000 ff7fffff + cp.b fff80000 ff780000 80000 + + +U-boot/kermit commands for downloading an image, then copying +it into the secondary bank: + + loadb + [Drop to kermit: + ^\c + send <u-boot-bin-image> + c + ] + + erase ff780000 ff7fffff + cp.b $loadaddr ff780000 80000 + + +U-boot commands for downloading an image via tftp and flashing +it into the second bank: + + tftp 10000 <u-boot.bin.image> + erase ff780000 ff7fffff + cp.b 10000 ff780000 80000 + + +After copying the image into the second bank of flash, be sure to toggle +SW2[2] on the carrier card before resetting the board in order to set the +secondary bank as the boot-bank. + + +Carrier Board Switches +---------------------- + +As a reminder, you should read the README.mpc85xxads too. + +Most switches on the carrier board should not be changed. The only +user-settable switches on the carrier board are used to configure +the flash banks and determining the PCI slot. + +The first two bits of SW2 control how flash is used on the board: + + 12345678 + -------- + SW2=00XXXXXX FLASH: Boot bank 1, bank 2 available. + 01XXXXXX FLASH: Boot bank 2, bank 1 available (swapped). + 10XXXXXX FLASH: Boot promjet, bank 1 available + 11XXXXXX FLASH: Boot promjet, bank 2 available + +The boot bank is always mapped to FF80_0000 and listed first by +the "flinfo" command. The secondary bank is always FF00_0000. + +When using PCI, linux needs to know to which slot the CDS carrier is +connected.. By convention, the user-specific bits of SW2 are used to +convey this information: + + 12345678 + -------- + SW2=xxxxxx00 PCI SLOT INFORM: The CDS carrier is in slot0 of the Arcadia + xxxxxx01 PCI SLOT INFORM: The CDS carrier is in slot1 of the Arcadia + xxxxxx10 PCI SLOT INFORM: The CDS carrier is in slot2 of the Arcadia + xxxxxx11 PCI SLOT INFORM: The CDS carrier is in slot3 of the Arcadia + +These are cleverly, er, clearly silkscreened as Slot 1 through 4, +respectively, on the Arcadia near the support posts. + + +The default setting of all switches on the carrier board is: + + 12345678 + -------- + SW1=01101100 + SW2=0x1111yy x=Flash bank, yy=PCI slot + SW3=11101111 + SW4=10001000 + + +8555/41 CPU Card Switches +------------------------- + +Most switches on the CPU Card should not be changed. However, the +frequency can be changed by setting SW3: + + 12345678 + -------- + SW3=XX00XXXX == CORE:CCB 2:1 + XX01XXXX == CORE:CCB 5:2 + XX10XXXX == CORE:CCB 3:1 + XX11XXXX == CORE:CCB 7:2 + XXXX1000 == CCB:SYSCLK 8:1 + XXXX1010 == CCB:SYSCLK 10:1 + +A safe default setting for all switches on the CPU board is: + + 12345678 + -------- + SW1=10001111 + SW2=01000111 + SW3=00001000 + SW4=11111110 + + +8548 CPU Card Switches +---------------------- +And, just to be confusing, in this set of switches: + + ON = 1 + OFF = 0 + +Default + SW1=11111101 + SW2=10011111 + SW3=11001000 (8X) (2:1) + SW4=11110011 + + SW3=X000XXXX == CORE:CCB 4:1 + X001XXXX == CORE:CCB 9:2 + X010XXXX == CORE:CCB 1:1 + X011XXXX == CORE:CCB 3:2 + X100XXXX == CORE:CCB 2:1 + X101XXXX == CORE:CCB 5:2 + X110XXXX == CORE:CCB 3:1 + X111XXXX == CORE:CCB 7:2 + XXXX0000 == CCB:SYSCLK 16:1 + XXXX0001 == RESERVED + XXXX0010 == CCB:SYSCLK 2:1 + XXXX0011 == CCB:SYSCLK 3:1 + XXXX0100 == CCB:SYSCLK 4:1 + XXXX0101 == CCB:SYSCLK 5:1 + XXXX0110 == CCB:SYSCLK 6:1 + XXXX0111 == RESERVED + XXXX1000 == CCB:SYSCLK 8:1 + XXXX1001 == CCB:SYSCLK 9:1 + XXXX1010 == CCB:SYSCLK 10:1 + XXXX1011 == RESERVED + XXXX1100 == CCB:SYSCLK 12:1 + XXXX1101 == CCB:SYSCLK 20:1 + XXXX1110 == RESERVED + XXXX1111 == RESERVED + + +eDINK Info +---------- + +One bank of flash may contain an eDINK image. + +Memory Map: + + CCSRBAR @ 0xe0000000 + Flash Bank 1 @ 0xfe000000 + Flash Bank 2 @ 0xff000000 + Ram @ 0 + +Commands for downloading a u-boot image to memory from edink: + + env -c + time -s 4/8/2004 4:30p + dl -k -b -o 100000 + [Drop to kermit: + ^\c + transmit /binary <u-boot-bin-image> + c + ] + + fu -l 100000 fe780000 80000 |