diff options
Diffstat (limited to 'roms/u-boot/arch/powerpc/cpu/ppc4xx/miiphy.c')
| -rw-r--r-- | roms/u-boot/arch/powerpc/cpu/ppc4xx/miiphy.c | 346 |
1 files changed, 346 insertions, 0 deletions
diff --git a/roms/u-boot/arch/powerpc/cpu/ppc4xx/miiphy.c b/roms/u-boot/arch/powerpc/cpu/ppc4xx/miiphy.c new file mode 100644 index 00000000..10147de0 --- /dev/null +++ b/roms/u-boot/arch/powerpc/cpu/ppc4xx/miiphy.c @@ -0,0 +1,346 @@ +/* + * SPDX-License-Identifier: GPL-2.0 IBM-pibs + */ +/*-----------------------------------------------------------------------------+ + | + | File Name: miiphy.c + | + | Function: This module has utilities for accessing the MII PHY through + | the EMAC3 macro. + | + | Author: Mark Wisner + | + +-----------------------------------------------------------------------------*/ + +/* define DEBUG for debugging output (obviously ;-)) */ +#if 0 +#define DEBUG +#endif + +#include <common.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <ppc_asm.tmpl> +#include <commproc.h> +#include <asm/ppc4xx-emac.h> +#include <asm/ppc4xx-mal.h> +#include <miiphy.h> + +#if !defined(CONFIG_PHY_CLK_FREQ) +#define CONFIG_PHY_CLK_FREQ 0 +#endif + +/***********************************************************/ +/* Dump out to the screen PHY regs */ +/***********************************************************/ + +void miiphy_dump (char *devname, unsigned char addr) +{ + unsigned long i; + unsigned short data; + + for (i = 0; i < 0x1A; i++) { + if (miiphy_read (devname, addr, i, &data)) { + printf ("read error for reg %lx\n", i); + return; + } + printf ("Phy reg %lx ==> %4x\n", i, data); + + /* jump to the next set of regs */ + if (i == 0x07) + i = 0x0f; + + } /* end for loop */ +} /* end dump */ + +/***********************************************************/ +/* (Re)start autonegotiation */ +/***********************************************************/ +int phy_setup_aneg (char *devname, unsigned char addr) +{ + u16 bmcr; + +#if defined(CONFIG_PHY_DYNAMIC_ANEG) + /* + * Set up advertisement based on capablilities reported by the PHY. + * This should work for both copper and fiber. + */ + u16 bmsr; +#if defined(CONFIG_PHY_GIGE) + u16 exsr = 0x0000; +#endif + + miiphy_read (devname, addr, MII_BMSR, &bmsr); + +#if defined(CONFIG_PHY_GIGE) + if (bmsr & BMSR_ESTATEN) + miiphy_read (devname, addr, MII_ESTATUS, &exsr); + + if (exsr & (ESTATUS_1000XF | ESTATUS_1000XH)) { + /* 1000BASE-X */ + u16 anar = 0x0000; + + if (exsr & ESTATUS_1000XF) + anar |= ADVERTISE_1000XFULL; + + if (exsr & ESTATUS_1000XH) + anar |= ADVERTISE_1000XHALF; + + miiphy_write (devname, addr, MII_ADVERTISE, anar); + } else +#endif + { + u16 anar, btcr; + + miiphy_read (devname, addr, MII_ADVERTISE, &anar); + anar &= ~(0x5000 | LPA_100BASE4 | LPA_100FULL | + LPA_100HALF | LPA_10FULL | LPA_10HALF); + + miiphy_read (devname, addr, MII_CTRL1000, &btcr); + btcr &= ~(0x00FF | PHY_1000BTCR_1000FD | PHY_1000BTCR_1000HD); + + if (bmsr & BMSR_100BASE4) + anar |= LPA_100BASE4; + + if (bmsr & BMSR_100FULL) + anar |= LPA_100FULL; + + if (bmsr & BMSR_100HALF) + anar |= LPA_100HALF; + + if (bmsr & BMSR_10FULL) + anar |= LPA_10FULL; + + if (bmsr & BMSR_10HALF) + anar |= LPA_10HALF; + + miiphy_write (devname, addr, MII_ADVERTISE, anar); + +#if defined(CONFIG_PHY_GIGE) + if (exsr & ESTATUS_1000_TFULL) + btcr |= PHY_1000BTCR_1000FD; + + if (exsr & ESTATUS_1000_THALF) + btcr |= PHY_1000BTCR_1000HD; + + miiphy_write (devname, addr, MII_CTRL1000, btcr); +#endif + } + +#else /* defined(CONFIG_PHY_DYNAMIC_ANEG) */ + /* + * Set up standard advertisement + */ + u16 adv; + + miiphy_read (devname, addr, MII_ADVERTISE, &adv); + adv |= (LPA_LPACK | LPA_100FULL | LPA_100HALF | + LPA_10FULL | LPA_10HALF); + miiphy_write (devname, addr, MII_ADVERTISE, adv); + + miiphy_read (devname, addr, MII_CTRL1000, &adv); + adv |= (0x0300); + miiphy_write (devname, addr, MII_CTRL1000, adv); + +#endif /* defined(CONFIG_PHY_DYNAMIC_ANEG) */ + + /* Start/Restart aneg */ + miiphy_read (devname, addr, MII_BMCR, &bmcr); + bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART); + miiphy_write (devname, addr, MII_BMCR, bmcr); + + return 0; +} + +/***********************************************************/ +/* read a phy reg and return the value with a rc */ +/***********************************************************/ +/* AMCC_TODO: + * Find out of the choice for the emac for MDIO is from the bridges, + * i.e. ZMII or RGMII as approporiate. If the bridges are not used + * to determine the emac for MDIO, then is the SDR0_ETH_CFG[MDIO_SEL] + * used? If so, then this routine below does not apply to the 460EX/GT. + * + * sr: Currently on 460EX only EMAC0 works with MDIO, so we always + * return EMAC0 offset here + * vg: For 460EX/460GT if internal GPCS PHY address is specified + * return appropriate EMAC offset + */ +unsigned int miiphy_getemac_offset(u8 addr) +{ +#if defined(CONFIG_440) && \ + !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ + !defined(CONFIG_460EX) && !defined(CONFIG_460GT) + unsigned long zmii; + unsigned long eoffset; + + /* Need to find out which mdi port we're using */ + zmii = in_be32((void *)ZMII0_FER); + + if (zmii & (ZMII_FER_MDI << ZMII_FER_V (0))) + /* using port 0 */ + eoffset = 0; + + else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (1))) + /* using port 1 */ + eoffset = 0x100; + + else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (2))) + /* using port 2 */ + eoffset = 0x400; + + else if (zmii & (ZMII_FER_MDI << ZMII_FER_V (3))) + /* using port 3 */ + eoffset = 0x600; + + else { + /* None of the mdi ports are enabled! */ + /* enable port 0 */ + zmii |= ZMII_FER_MDI << ZMII_FER_V (0); + out_be32((void *)ZMII0_FER, zmii); + eoffset = 0; + /* need to soft reset port 0 */ + zmii = in_be32((void *)EMAC0_MR0); + zmii |= EMAC_MR0_SRST; + out_be32((void *)EMAC0_MR0, zmii); + } + + return (eoffset); +#else + +#if defined(CONFIG_405EX) + unsigned long rgmii; + int devnum = 1; + + rgmii = in_be32((void *)RGMII_FER); + if (rgmii & (1 << (19 - devnum))) + return 0x100; +#endif + +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) + u32 eoffset = 0; + + switch (addr) { +#if defined(CONFIG_HAS_ETH1) && defined(CONFIG_GPCS_PHY1_ADDR) + case CONFIG_GPCS_PHY1_ADDR: + if (addr == EMAC_MR1_IPPA_GET(in_be32((void *)EMAC0_MR1 + 0x100))) + eoffset = 0x100; + break; +#endif +#if defined(CONFIG_HAS_ETH2) && defined(CONFIG_GPCS_PHY2_ADDR) + case CONFIG_GPCS_PHY2_ADDR: + if (addr == EMAC_MR1_IPPA_GET(in_be32((void *)EMAC0_MR1 + 0x300))) + eoffset = 0x300; + break; +#endif +#if defined(CONFIG_HAS_ETH3) && defined(CONFIG_GPCS_PHY3_ADDR) + case CONFIG_GPCS_PHY3_ADDR: + if (addr == EMAC_MR1_IPPA_GET(in_be32((void *)EMAC0_MR1 + 0x400))) + eoffset = 0x400; + break; +#endif + default: + eoffset = 0; + break; + } + return eoffset; +#endif + + return 0; +#endif +} + +static int emac_miiphy_wait(u32 emac_reg) +{ + u32 sta_reg; + int i; + + /* wait for completion */ + i = 0; + do { + sta_reg = in_be32((void *)EMAC0_STACR + emac_reg); + if (i++ > 5) { + debug("%s [%d]: Timeout! EMAC0_STACR=0x%0x\n", __func__, + __LINE__, sta_reg); + return -1; + } + udelay(10); + } while ((sta_reg & EMAC_STACR_OC) == EMAC_STACR_OC_MASK); + + return 0; +} + +static int emac_miiphy_command(u8 addr, u8 reg, int cmd, u16 value) +{ + u32 emac_reg; + u32 sta_reg; + + emac_reg = miiphy_getemac_offset(addr); + + /* wait for completion */ + if (emac_miiphy_wait(emac_reg) != 0) + return -1; + + sta_reg = reg; /* reg address */ + + /* set clock (50MHz) and read flags */ +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_405EX) +#if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */ + sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | cmd; +#else + sta_reg |= cmd; +#endif +#else + sta_reg = (sta_reg | cmd) & ~EMAC_STACR_CLK_100MHZ; +#endif + + /* Some boards (mainly 405EP based) define the PHY clock freqency fixed */ + sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; + sta_reg = sta_reg | ((u32)addr << 5); /* Phy address */ + sta_reg = sta_reg | EMAC_STACR_OC_MASK; /* new IBM emac v4 */ + if (cmd == EMAC_STACR_WRITE) + memcpy(&sta_reg, &value, 2); /* put in data */ + + out_be32((void *)EMAC0_STACR + emac_reg, sta_reg); + debug("%s [%d]: sta_reg=%08x\n", __func__, __LINE__, sta_reg); + + /* wait for completion */ + if (emac_miiphy_wait(emac_reg) != 0) + return -1; + + debug("%s [%d]: sta_reg=%08x\n", __func__, __LINE__, sta_reg); + if ((sta_reg & EMAC_STACR_PHYE) != 0) + return -1; + + return 0; +} + +int emac4xx_miiphy_read (const char *devname, unsigned char addr, unsigned char reg, + unsigned short *value) +{ + unsigned long sta_reg; + unsigned long emac_reg; + + emac_reg = miiphy_getemac_offset(addr); + + if (emac_miiphy_command(addr, reg, EMAC_STACR_READ, 0) != 0) + return -1; + + sta_reg = in_be32((void *)EMAC0_STACR + emac_reg); + *value = sta_reg >> 16; + + return 0; +} + +/***********************************************************/ +/* write a phy reg and return the value with a rc */ +/***********************************************************/ + +int emac4xx_miiphy_write (const char *devname, unsigned char addr, unsigned char reg, + unsigned short value) +{ + return emac_miiphy_command(addr, reg, EMAC_STACR_WRITE, value); +} |