diff options
Diffstat (limited to 'roms/u-boot/arch/powerpc/cpu/mpc824x/cpu_init.c')
| -rw-r--r-- | roms/u-boot/arch/powerpc/cpu/mpc824x/cpu_init.c | 311 |
1 files changed, 311 insertions, 0 deletions
diff --git a/roms/u-boot/arch/powerpc/cpu/mpc824x/cpu_init.c b/roms/u-boot/arch/powerpc/cpu/mpc824x/cpu_init.c new file mode 100644 index 00000000..68d88e91 --- /dev/null +++ b/roms/u-boot/arch/powerpc/cpu/mpc824x/cpu_init.c @@ -0,0 +1,311 @@ +/* + * (C) Copyright 2000 + * Rob Taylor. Flying Pig Systems. robt@flyingpig.com. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/processor.h> +#include <mpc824x.h> + +#ifndef CONFIG_SYS_BANK0_ROW +#define CONFIG_SYS_BANK0_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK1_ROW +#define CONFIG_SYS_BANK1_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK2_ROW +#define CONFIG_SYS_BANK2_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK3_ROW +#define CONFIG_SYS_BANK3_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK4_ROW +#define CONFIG_SYS_BANK4_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK5_ROW +#define CONFIG_SYS_BANK5_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK6_ROW +#define CONFIG_SYS_BANK6_ROW 0 +#endif +#ifndef CONFIG_SYS_BANK7_ROW +#define CONFIG_SYS_BANK7_ROW 0 +#endif +#ifndef CONFIG_SYS_DBUS_SIZE2 +#define CONFIG_SYS_DBUS_SIZE2 0 +#endif + +/* + * Breath some life into the CPU... + * + * Set up the memory map, + * initialize a bunch of registers, + */ +void +cpu_init_f (void) +{ + register unsigned long val; + CONFIG_WRITE_HALFWORD(PCICR, 0x06); /* Bus Master, respond to PCI memory space acesses*/ +/* CONFIG_WRITE_HALFWORD(PCISR, 0xffff); */ /*reset PCISR*/ + +#if defined(CONFIG_MUSENKI) +/* Why is this here, you ask? Try, just try setting 0x8000 + * in PCIACR with CONFIG_WRITE_HALFWORD() + * this one was a stumper, and we are annoyed + */ + +#define M_CONFIG_WRITE_HALFWORD( addr, data ) \ + __asm__ __volatile__(" \ + stw %2,0(%0)\n \ + sync\n \ + sth %3,2(%1)\n \ + sync\n \ + " \ + : /* no output */ \ + : "r" (CONFIG_ADDR), "r" (CONFIG_DATA), \ + "r" (PCISWAP(addr & ~3)), "r" (PCISWAP(data << 16)) \ + ); + + M_CONFIG_WRITE_HALFWORD(PCIACR, 0x8000); +#endif + + CONFIG_WRITE_BYTE(PCLSR, 0x8); /* set PCI cache line size */ + CONFIG_WRITE_BYTE (PLTR, 0x40); /* set PCI latency timer */ + /* + * Note that although this bit is cleared after a hard reset, it + * must be explicitly set and then cleared by software during + * initialization in order to guarantee correct operation of the + * DLL and the SDRAM_CLK[0:3] signals (if they are used). + */ + CONFIG_READ_BYTE (AMBOR, val); + CONFIG_WRITE_BYTE(AMBOR, val & 0xDF); + CONFIG_WRITE_BYTE(AMBOR, val | 0x20); + CONFIG_WRITE_BYTE(AMBOR, val & 0xDF); +#ifdef CONFIG_MPC8245 + /* silicon bug 28 MPC8245 */ + CONFIG_READ_BYTE(AMBOR,val); + CONFIG_WRITE_BYTE(AMBOR,val|0x1); + +#if 0 + /* + * The following bug only affects older (XPC8245) processors. + * DMA transfers initiated by external devices get corrupted due + * to a hardware scheduling problem. + * + * The effect is: + * when transferring X words, the first 32 words are transferred + * OK, the next 3 x 32 words are 'old' data (from previous DMA) + * while the rest of the X words is xferred fine. + * + * Disabling 3 of the 4 32 word hardware buffers solves the problem + * with no significant performance loss. + */ + + CONFIG_READ_BYTE(PCMBCR,val); + /* in order not to corrupt data which is being read over the PCI bus + * with the PPC as slave, we need to reduce the number of PCMRBs to 1, + * 4.11 in the processor user manual + * */ + +#if 1 + CONFIG_WRITE_BYTE(PCMBCR,(val|0xC0)); /* 1 PCMRB */ +#else + CONFIG_WRITE_BYTE(PCMBCR,(val|0x80)); /* 2 PCMRBs */ + CONFIG_WRITE_BYTE(PCMBCR,(val|0x40)); /* 3 PCMRBs */ + /* default, 4 PCMRBs are used */ +#endif +#endif +#endif + + CONFIG_READ_WORD(PICR1, val); +#if defined(CONFIG_MPC8240) + CONFIG_WRITE_WORD( PICR1, + (val & (PICR1_ADDRESS_MAP | PICR1_RCS0)) | + PIRC1_MSK | PICR1_PROC_TYPE_603E | + PICR1_FLASH_WR_EN | PICR1_MCP_EN | + PICR1_CF_DPARK | PICR1_EN_PCS | + PICR1_CF_APARK ); +#elif defined(CONFIG_MPC8245) + CONFIG_WRITE_WORD( PICR1, + (val & (PICR1_RCS0)) | + PICR1_PROC_TYPE_603E | + PICR1_FLASH_WR_EN | PICR1_MCP_EN | + PICR1_CF_DPARK | PICR1_NO_BUSW_CK | + PICR1_DEC| PICR1_CF_APARK | 0x10); /* 8245 UM says bit 4 must be set */ +#else +#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif + + CONFIG_READ_WORD(PICR2, val); + val= val & ~ (PICR2_CF_SNOOP_WS_MASK | PICR2_CF_APHASE_WS_MASK); /*mask off waitstate bits*/ + val |= PICR2_CF_SNOOP_WS_1WS | PICR2_CF_APHASE_WS_1WS; /*1 wait state*/ + CONFIG_WRITE_WORD(PICR2, val); + + CONFIG_WRITE_WORD(EUMBBAR, CONFIG_SYS_EUMB_ADDR); +#ifndef CONFIG_SYS_RAMBOOT + CONFIG_WRITE_WORD(MCCR1, (CONFIG_SYS_ROMNAL << MCCR1_ROMNAL_SHIFT) | + (CONFIG_SYS_BANK0_ROW) | + (CONFIG_SYS_BANK1_ROW << MCCR1_BANK1ROW_SHIFT) | + (CONFIG_SYS_BANK2_ROW << MCCR1_BANK2ROW_SHIFT) | + (CONFIG_SYS_BANK3_ROW << MCCR1_BANK3ROW_SHIFT) | + (CONFIG_SYS_BANK4_ROW << MCCR1_BANK4ROW_SHIFT) | + (CONFIG_SYS_BANK5_ROW << MCCR1_BANK5ROW_SHIFT) | + (CONFIG_SYS_BANK6_ROW << MCCR1_BANK6ROW_SHIFT) | + (CONFIG_SYS_BANK7_ROW << MCCR1_BANK7ROW_SHIFT) | + (CONFIG_SYS_ROMFAL << MCCR1_ROMFAL_SHIFT)); +#endif + +#if defined(CONFIG_SYS_ASRISE) && defined(CONFIG_SYS_ASFALL) + CONFIG_WRITE_WORD(MCCR2, CONFIG_SYS_REFINT << MCCR2_REFINT_SHIFT | + CONFIG_SYS_ASRISE << MCCR2_ASRISE_SHIFT | + CONFIG_SYS_ASFALL << MCCR2_ASFALL_SHIFT); +#else + CONFIG_WRITE_WORD(MCCR2, CONFIG_SYS_REFINT << MCCR2_REFINT_SHIFT); +#endif + +#if defined(CONFIG_MPC8240) + CONFIG_WRITE_WORD(MCCR3, + (((CONFIG_SYS_BSTOPRE & 0x003c) >> 2) << MCCR3_BSTOPRE2TO5_SHIFT) | + (CONFIG_SYS_REFREC << MCCR3_REFREC_SHIFT) | + (CONFIG_SYS_RDLAT << MCCR3_RDLAT_SHIFT)); +#elif defined(CONFIG_MPC8245) + CONFIG_WRITE_WORD(MCCR3, + (((CONFIG_SYS_BSTOPRE & 0x003c) >> 2) << MCCR3_BSTOPRE2TO5_SHIFT) | + (CONFIG_SYS_REFREC << MCCR3_REFREC_SHIFT)); +#else +#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif + +/* this is gross. We think these should all be the same, and various boards + * should define CONFIG_SYS_ACTORW to 0 if they don't want to set it, or even, if + * its not set, we define it to zero in this file + */ +#if defined(CONFIG_CU824) + CONFIG_WRITE_WORD(MCCR4, + (CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) | + (CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) | + MCCR4_BIT21 | + (CONFIG_SYS_REGISTERD_TYPE_BUFFER ? MCCR4_REGISTERED: 0) | + ((CONFIG_SYS_BSTOPRE & 0x0003) <<MCCR4_BSTOPRE0TO1_SHIFT ) | + (((CONFIG_SYS_SDMODE_CAS_LAT <<4) | (CONFIG_SYS_SDMODE_WRAP <<3) | + CONFIG_SYS_SDMODE_BURSTLEN) << MCCR4_SDMODE_SHIFT) | + (CONFIG_SYS_ACTORW << MCCR4_ACTTORW_SHIFT) | + (((CONFIG_SYS_BSTOPRE & 0x03c0) >> 6) << MCCR4_BSTOPRE6TO9_SHIFT)); +#elif defined(CONFIG_MPC8240) + CONFIG_WRITE_WORD(MCCR4, + (CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) | + (CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) | + MCCR4_BIT21 | + (CONFIG_SYS_REGISTERD_TYPE_BUFFER ? MCCR4_REGISTERED: 0) | + ((CONFIG_SYS_BSTOPRE & 0x0003) <<MCCR4_BSTOPRE0TO1_SHIFT ) | + (((CONFIG_SYS_SDMODE_CAS_LAT <<4) | (CONFIG_SYS_SDMODE_WRAP <<3) | + (CONFIG_SYS_SDMODE_BURSTLEN)) <<MCCR4_SDMODE_SHIFT) | + (((CONFIG_SYS_BSTOPRE & 0x03c0) >> 6) <<MCCR4_BSTOPRE6TO9_SHIFT )); +#elif defined(CONFIG_MPC8245) + CONFIG_READ_WORD(MCCR1, val); + val &= MCCR1_DBUS_SIZE0; /* test for 64-bit mem bus */ + + CONFIG_WRITE_WORD(MCCR4, + (CONFIG_SYS_PRETOACT << MCCR4_PRETOACT_SHIFT) | + (CONFIG_SYS_ACTTOPRE << MCCR4_ACTTOPRE_SHIFT) | + (CONFIG_SYS_EXTROM ? MCCR4_EXTROM : 0) | + (CONFIG_SYS_REGDIMM ? MCCR4_REGDIMM : 0) | + (CONFIG_SYS_REGISTERD_TYPE_BUFFER ? MCCR4_REGISTERED: 0) | + ((CONFIG_SYS_BSTOPRE & 0x0003) <<MCCR4_BSTOPRE0TO1_SHIFT ) | + (CONFIG_SYS_DBUS_SIZE2 << MCCR4_DBUS_SIZE2_SHIFT) | + (((CONFIG_SYS_SDMODE_CAS_LAT <<4) | (CONFIG_SYS_SDMODE_WRAP <<3) | + (val ? 2 : 3)) << MCCR4_SDMODE_SHIFT) | + (CONFIG_SYS_ACTORW << MCCR4_ACTTORW_SHIFT) | + (((CONFIG_SYS_BSTOPRE & 0x03c0) >> 6) <<MCCR4_BSTOPRE6TO9_SHIFT )); +#else +#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) +#endif + + CONFIG_WRITE_WORD(MSAR1, + ( (CONFIG_SYS_BANK0_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) | + (((CONFIG_SYS_BANK1_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK2_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK3_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(EMSAR1, + ( (CONFIG_SYS_BANK0_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) | + (((CONFIG_SYS_BANK1_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK2_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK3_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(MSAR2, + ( (CONFIG_SYS_BANK4_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) | + (((CONFIG_SYS_BANK5_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK6_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK7_START & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(EMSAR2, + ( (CONFIG_SYS_BANK4_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) | + (((CONFIG_SYS_BANK5_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK6_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK7_START & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(MEAR1, + ( (CONFIG_SYS_BANK0_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) | + (((CONFIG_SYS_BANK1_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK2_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK3_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(EMEAR1, + ( (CONFIG_SYS_BANK0_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) | + (((CONFIG_SYS_BANK1_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK2_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK3_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(MEAR2, + ( (CONFIG_SYS_BANK4_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) | + (((CONFIG_SYS_BANK5_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK6_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK7_END & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) << 24)); + CONFIG_WRITE_WORD(EMEAR2, + ( (CONFIG_SYS_BANK4_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) | + (((CONFIG_SYS_BANK5_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 8) | + (((CONFIG_SYS_BANK6_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 16) | + (((CONFIG_SYS_BANK7_END & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) << 24)); + + CONFIG_WRITE_BYTE(ODCR, CONFIG_SYS_ODCR); +#ifdef CONFIG_SYS_DLL_MAX_DELAY + CONFIG_WRITE_BYTE(MIOCR1, CONFIG_SYS_DLL_MAX_DELAY); /* needed to make DLL lock */ +#endif +#if defined(CONFIG_SYS_DLL_EXTEND) && defined(CONFIG_SYS_PCI_HOLD_DEL) + CONFIG_WRITE_BYTE(PMCR2, CONFIG_SYS_DLL_EXTEND | CONFIG_SYS_PCI_HOLD_DEL); +#endif +#if defined(MIOCR2) && defined(CONFIG_SYS_SDRAM_DSCD) + CONFIG_WRITE_BYTE(MIOCR2, CONFIG_SYS_SDRAM_DSCD); /* change memory input */ +#endif /* setup & hold time */ + + CONFIG_WRITE_BYTE(MBER, + CONFIG_SYS_BANK0_ENABLE | + (CONFIG_SYS_BANK1_ENABLE << 1) | + (CONFIG_SYS_BANK2_ENABLE << 2) | + (CONFIG_SYS_BANK3_ENABLE << 3) | + (CONFIG_SYS_BANK4_ENABLE << 4) | + (CONFIG_SYS_BANK5_ENABLE << 5) | + (CONFIG_SYS_BANK6_ENABLE << 6) | + (CONFIG_SYS_BANK7_ENABLE << 7)); + +#ifdef CONFIG_SYS_PGMAX + CONFIG_WRITE_BYTE(MPMR, CONFIG_SYS_PGMAX); +#endif + + /* ! Wait 200us before initialize other registers */ + /*FIXME: write a decent udelay wait */ + __asm__ __volatile__( + " mtctr %0 \n \ + 0: bdnz 0b\n" + : + : "r" (0x10000)); + + CONFIG_READ_WORD(MCCR1, val); + CONFIG_WRITE_WORD(MCCR1, val | MCCR1_MEMGO); /* set memory access going */ + __asm__ __volatile__("eieio"); +} + +/* + * initialize higher level parts of CPU like time base and timers + */ +int cpu_init_r (void) +{ + return (0); +} |