1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
From 409f4b56de7611d703790c54a70fad9a6e2bb161 Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Wed, 1 Mar 2017 16:07:39 +0000
Subject: [PATCH] amba_pl011: Round input clock up
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
---
drivers/tty/serial/amba-pl011.c | 23 +++++++++++++++++++++--
1 file changed, 21 insertions(+), 2 deletions(-)
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1662,6 +1662,23 @@ static void pl011_put_poll_char(struct u
#endif /* CONFIG_CONSOLE_POLL */
+unsigned long pl011_clk_round(unsigned long clk)
+{
+ unsigned long scaler;
+
+ /*
+ * If increasing a clock by less than 0.1% changes it
+ * from ..999.. to ..000.., round up.
+ */
+ scaler = 1;
+ while (scaler * 100000 < clk)
+ scaler *= 10;
+ if ((clk + scaler - 1)/scaler % 1000 == 0)
+ clk = (clk/scaler + 1) * scaler;
+
+ return clk;
+}
+
static int pl011_hwinit(struct uart_port *port)
{
struct uart_amba_port *uap =
@@ -1678,7 +1695,7 @@ static int pl011_hwinit(struct uart_port
if (retval)
return retval;
- uap->port.uartclk = clk_get_rate(uap->clk);
+ uap->port.uartclk = pl011_clk_round(clk_get_rate(uap->clk));
/* Clear pending error and receive interrupts */
pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS |
@@ -2322,7 +2339,7 @@ static int pl011_console_setup(struct co
plat->init();
}
- uap->port.uartclk = clk_get_rate(uap->clk);
+ uap->port.uartclk = pl011_clk_round(clk_get_rate(uap->clk));
if (uap->vendor->fixed_options) {
baud = uap->fixed_baud;
@@ -2507,6 +2524,7 @@ static struct uart_driver amba_reg = {
.cons = AMBA_CONSOLE,
};
+#if 0
static int pl011_probe_dt_alias(int index, struct device *dev)
{
struct device_node *np;
@@ -2538,6 +2556,7 @@ static int pl011_probe_dt_alias(int inde
return ret;
}
+#endif
/* unregisters the driver also if no more ports are left */
static void pl011_unregister_port(struct uart_amba_port *uap)
|
