1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
|
From 3c54a4cdc8c65248c347a02b36ac378fe81379ba Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dave.stevenson@raspberrypi.org>
Date: Wed, 28 Aug 2019 13:34:30 +0100
Subject: [PATCH] media: dt-bindings: Add binding for the Sony IMX219
sensor
The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes.
Document the binding for this device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
---
.../devicetree/bindings/media/i2c/imx219.txt | 59 +++++++++++++++++++
1 file changed, 59 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx219.txt
@@ -0,0 +1,59 @@
+* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
+
+The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with
+an active array size of 3280H x 2464V. It is programmable through I2C
+interface. The I2C address is fixed to 0x10 as per sensor data sheet.
+Image data is sent through MIPI CSI-2, which is configured as either 2 or 4
+data lanes.
+
+Required Properties:
+- compatible: value should be "sony,imx219" for imx219 sensor
+- reg: I2C bus address of the device
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.2 volts
+
+Optional Properties:
+- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be
+ released after all supplies are applied.
+ This is an active high signal to the imx219.
+
+The imx219 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1 2>, or <1 2 3 4> (two or four lane CSI-2
+ supported)
+
+Example:
+ sensor@10 {
+ compatible = "sony,imx219";
+ reg = <0x10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&imx219_clk>;
+ clock-names = "xclk";
+ xclr-gpios = <&gpio_sensor 0 0>;
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v */
+ DVDD-supply = <&vgen2_reg>; /* 1.2v */
+
+ imx219_clk: camera-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ port {
+ sensor_out: endpoint {
+ remote-endpoint = <&csiss_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
|
