target/linux/ath79/dts/ar9331_etactica_eg200.dts


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "ar9331.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
	model = "eTactica EG200";
	compatible = "etactica,eg200", "qca,ar9331";

	aliases {
		led-boot = &led_etactica;
		led-failsafe = &led_etactica;
		led-upgrade = &led_etactica;
	};

	keys {
		compatible = "gpio-keys";

		restore {
			linux,code = <KEY_RESTART>;
			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
		};
	};

	leds {
		compatible = "gpio-leds";
		pinctrl-names = "default";
		pinctrl-0 = <&switch_led_disable_pins>;

		modbus {
			label = "red:modbus";
			gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
		};

		led_etactica: etactica {
			label = "red:etactica";
			gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
		};

		eth0 {
			label = "red:eth0";
			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
		};

		wlan {
			label = "red:wlan";
			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "phy0tpt";
		};
	};
};

&usb {
	dr_mode = "host";
	status = "okay";
};

&usb_phy {
	status = "okay";
};

&eth0 {
	status = "okay";
	nvmem-cells = <&macaddr_art_0>;
	nvmem-cell-names = "mac-address";

	gmac-config {
		device = <&gmac>;
		switch-phy-addr-swap = <1>;
		switch-phy-swap = <1>;
	};
};

&eth1 {
	status = "okay";
	compatible = "syscon", "simple-mfd";
};

&spi {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		spi-max-frequency = <50000000>;
		reg = <0>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			uboot@0 {
				reg = <0x0 0x40000>;
				read-only;
			};

			uboot-env@40000 {
				reg = <0x40000 0x10000>;
				read-only;
			};

			firmware@50000 {
				compatible = "denx,uimage";
				reg = <0x50000 0xfa0000>;
			};

			art: art@ff0000 {
				reg = <0xff0000 0x10000>;
				read-only;
			};
		};
	};
};

&wmac {
	status = "okay";
	mtd-cal-data = <&art 0x1000>;
};

&art {
	compatible = "nvmem-cells";
	#address-cells = <1>;
	#size-cells = <1>;

	macaddr_art_0: macaddr@0 {
		reg = <0x0 0x6>;
	};
};