1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
|
From 11e5bbe58eebdb10793eec374b6c8ccc7daf7ec8 Mon Sep 17 00:00:00 2001
From: Peter Oh <peter.oh@bowerswilkins.com>
Date: Tue, 30 Jun 2020 14:18:56 +0200
Subject: [PATCH 08/19] mesh: use setup completion callback to complete mesh
join
mesh join function is the last function to be called during
mesh join process, but it's been called a bit earlier than
it's supposed to be, so that some mesh parameter values
such as VHT capabilities not applied correct when mesh join
is in process.
Moreover current design of mesh join that is called directly
after mesh initialization isn't suitable for DFS channels to use,
since mesh join process should be paused until DFS CAC is
done and resumed after it's done.
The callback will be called by hostapd_setup_interface_complete_sync.
There is possiblity that completing mesh init fails, so add error
handle codes.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
---
src/ap/hostapd.c | 11 ++++++++++-
wpa_supplicant/mesh.c | 12 ++++++++++--
2 files changed, 20 insertions(+), 3 deletions(-)
--- a/src/ap/hostapd.c
+++ b/src/ap/hostapd.c
@@ -434,6 +434,8 @@ static void hostapd_free_hapd_data(struc
#ifdef CONFIG_MESH
wpabuf_free(hapd->mesh_pending_auth);
hapd->mesh_pending_auth = NULL;
+ /* handling setup failure is already done */
+ hapd->setup_complete_cb = NULL;
#endif /* CONFIG_MESH */
hostapd_clean_rrm(hapd);
@@ -2156,6 +2158,13 @@ dfs_offload:
if (hapd->setup_complete_cb)
hapd->setup_complete_cb(hapd->setup_complete_cb_ctx);
+#ifdef CONFIG_MESH
+ if (delay_apply_cfg && iface->mconf == NULL) {
+ wpa_printf(MSG_ERROR, "Error while completing mesh init");
+ goto fail;
+ }
+#endif /* CONFIG_MESH */
+
wpa_printf(MSG_DEBUG, "%s: Setup of interface done.",
iface->bss[0]->conf->iface);
if (iface->interfaces && iface->interfaces->terminate_on_error > 0)
@@ -2299,7 +2308,7 @@ int hostapd_setup_interface(struct hosta
ret = setup_interface(iface);
if (ret) {
wpa_printf(MSG_ERROR, "%s: Unable to setup interface.",
- iface->bss[0]->conf->iface);
+ iface->conf ? iface->conf->bss[0]->iface : "N/A");
return -1;
}
--- a/wpa_supplicant/mesh.c
+++ b/wpa_supplicant/mesh.c
@@ -193,7 +193,6 @@ static int wpas_mesh_init_rsn(struct wpa
return !wpa_s->mesh_rsn ? -1 : 0;
}
-
static int wpas_mesh_complete(struct wpa_supplicant *wpa_s)
{
struct hostapd_iface *ifmsh = wpa_s->ifmsh;
@@ -244,6 +243,13 @@ static int wpas_mesh_complete(struct wpa
}
+static void wpas_mesh_complete_cb(void *arg)
+{
+ struct wpa_supplicant *wpa_s = arg;
+ wpas_mesh_complete(wpa_s);
+}
+
+
static int wpa_supplicant_mesh_init(struct wpa_supplicant *wpa_s,
struct wpa_ssid *ssid,
struct hostapd_freq_params *freq)
@@ -267,6 +273,7 @@ static int wpa_supplicant_mesh_init(stru
if (!ifmsh)
return -ENOMEM;
+ ifmsh->owner = wpa_s;
ifmsh->drv_flags = wpa_s->drv_flags;
ifmsh->drv_flags2 = wpa_s->drv_flags2;
ifmsh->num_bss = 1;
@@ -285,6 +292,8 @@ static int wpa_supplicant_mesh_init(stru
bss->drv_priv = wpa_s->drv_priv;
bss->iface = ifmsh;
bss->mesh_sta_free_cb = mesh_mpm_free_sta;
+ bss->setup_complete_cb = wpas_mesh_complete_cb;
+ bss->setup_complete_cb_ctx = wpa_s;
frequency = ssid->frequency;
if (frequency != freq->freq &&
frequency == freq->freq + freq->sec_channel_offset * 20) {
@@ -523,7 +532,6 @@ int wpa_supplicant_join_mesh(struct wpa_
goto out;
}
- ret = wpas_mesh_complete(wpa_s);
out:
return ret;
}
|
