diff options
Diffstat (limited to 'target/linux/ipq806x')
9 files changed, 624 insertions, 3 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 769afb8b85..509d334c41 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -11,6 +11,10 @@ board=$(board_name) boardname="${board##*,}" case "$board" in +buffalo,wxr-2533dhp) + ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:white:wireless" "phy0tpt" + ucidef_set_led_switch "wan" "WAN" "${boardname}:white:internet" "switch0" "0x20" + ;; compex,wpq864) ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1" ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 3417466fbb..a3aa0fce70 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -12,6 +12,7 @@ board_config_update board=$(board_name) case "$board" in +buffalo,wxr-2533dhp |\ compex,wpq864 |\ netgear,d7800 |\ netgear,r7500 |\ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index ba7a8e0b14..e05f2b2c7b 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -79,6 +79,10 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/pre-cal-pci-0000:01:00.0.bin") case $board in + buffalo,wxr-2533dhp) + ath10kcal_extract "ART" 4096 12064 + ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 30) + ;; linksys,ea8500) ath10kcal_extract "art" 4096 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1) @@ -109,6 +113,10 @@ case "$FIRMWARE" in ;; "ath10k/pre-cal-pci-0001:01:00.0.bin") case $board in + buffalo,wxr-2533dhp) + ath10kcal_extract "ART" 20480 12064 + ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 24) + ;; linksys,ea8500) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2) diff --git a/target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh b/target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh new file mode 100644 index 0000000000..77fa65e60e --- /dev/null +++ b/target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh @@ -0,0 +1,45 @@ +#!/bin/sh +# Copyright (C) 2018 OpenWrt.org +# + +. /lib/functions.sh + +# The mtd partition 'ubi' and 'rootfs_1' on NAND flash are os-image +# partitions. These partitions are called as "Bank1/Bank2" in U-Boot +# on WXR-2533DHP, and they are checked conditions when booting. +# Then, U-Boot checks kernel and rootfs volumes in ubi, but U-Boot +# needs "ubi_rootfs" as rootfs volume name. And, U-Boot checks the +# checksum at the end of rootfs (ubi_rootfs). +# When U-Boot writes os-image into the Bank, only kernel, rootfs +# (ubi_rootfs) and rootfs_data (ubi_rootfs_data) volumes are wrote +# into the Bank. (not full ubi image) +# +# == U-Boot Behaviors == +# - Bank1/Bank2 images are good, images are different +# -> writes os-image to Bank1 from Bank2 +# (this behavior is used to firmware upgrade in stock firmware) +# - Bank1 image is broken (or checksum error) +# -> writes os-image to Bank1 from Bank2 +# - Bank2 image is broken (or checksum error) +# -> writes os-image to Bank2 from Bank1 +# - Bank1/Bank2 images are broken (or checksum error) +# -> start tftp + +buffalo_upgrade_prepare_ubi() { + local ubidev="$( nand_find_ubi ubi )" + local mtdnum2="$( find_mtd_index rootfs_1 )" + + if [ ! "$mtdnum2" ]; then + echo "cannot find second ubi mtd partition rootfs_1" + return 1 + fi + + local ubidev2="$( nand_find_ubi rootfs_1 )" + if [ ! "$ubidev2" ] && [ -n "$mtdnum2" ]; then + ubiattach -m "$mtdnum2" + ubidev2="$( nand_find_ubi rootfs_1 )" + fi + + ubirmvol /dev/$ubidev -N ubi_rootfs_data &> /dev/null || true + ubirmvol /dev/$ubidev2 -N kernel &> /dev/null || true +} diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 4b88f9cf5e..2f0190629e 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -10,6 +10,11 @@ platform_check_image() { platform_do_upgrade() { case "$(board_name)" in + buffalo,wxr-2533dhp) + buffalo_upgrade_prepare_ubi + CI_ROOTPART="ubi_rootfs" + nand_do_upgrade "$ARGV" + ;; compex,wpq864|\ netgear,d7800 |\ netgear,r7500 |\ diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts new file mode 100644 index 0000000000..7b5ee799ee --- /dev/null +++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts @@ -0,0 +1,535 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +#include "qcom-ipq8064-v2.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Buffalo WXR-2533DHP"; + compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064"; + + memory@42000000 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &gsbi4_serial; + + led-boot = &power; + led-failsafe = &diag; + led-running = &power; + led-upgrade = &power; + }; + + chosen { + /* use "ubi_rootfs" volume in "ubi" partition as rootfs */ + bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs"; + stdout-path = "serial0:115200n8"; + }; + + soc { + nand@1ac00000 { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + cs@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ubi@0 { + label = "ubi"; + reg = <0x0000000 0x4000000>; + }; + + rootfs_1@4000000 { + label = "rootfs_1"; + reg = <0x4000000 0x4000000>; + }; + }; + }; + }; + + mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, + <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x07600000 /* PAD0_MODE */ + 0x00008 0x01000000 /* PAD5_MODE */ + 0x0000c 0x00000080 /* PAD6_MODE */ + 0x00050 0xcc35cc35 /* LED_CTRL0 */ + 0x00054 0xca35ca35 /* LED_CTRL1 */ + 0x00058 0xc935c935 /* LED_CTRL2 */ + 0x0005c 0x03ffff00 /* LED_CTRL3 */ + 0x000e4 0x0006a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x0000007e /* PORT0_STATUS */ + 0x00094 0x0000007e /* PORT6_STATUS */ + >; + }; + + ethernet-phy@4 { + reg = <4>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + usb { + label = "wxr-2533dhp:green:usb"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "usbport"; + trigger-sources = <&hub_port0 &hub_port1>; + }; + + guestport { + label = "wxr-2533dhp:green:guestport"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + diag: diag { + label = "wxr-2533dhp:orange:diag"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + internet_orange { + label = "wxr-2533dhp:orange:internet"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + + internet_white { + label = "wxr-2533dhp:white:internet"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + wireless_orange { + label = "wxr-2533dhp:orange:wireless"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + wireless_white { + label = "wxr-2533dhp:white:wireless"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + + router_orange { + label = "wxr-2533dhp:orange:router"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; + }; + + router_white { + label = "wxr-2533dhp:white:router"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + power: power { + label = "wxr-2533dhp:white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + power { + label = "power"; + gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + eject { + label = "eject"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_EJECTCD>; + }; + + guest { + label = "guest"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + }; + + ap { + label = "ap"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>; + linux,code = <BTN_1>; + linux,input-type = <EV_SW>; + }; + + router { + label = "router"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>; + linux,code = <BTN_1>; + linux,input-type = <EV_SW>; + }; + + auto { + label = "auto"; + gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>; + linux,code = <BTN_1>; + linux,input-type = <EV_SW>; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&gmac1 { + status = "okay"; + + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&ART 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "ok"; + + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&ART 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gsbi4 { + status = "okay"; + qcom,mode = <GSBI_PROT_I2C_UART>; +}; + +&gsbi4_serial { + status = "okay"; + + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +&gsbi5 { + status = "okay"; + qcom,mode = <GSBI_PROT_SPI>; + + spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x10000>; + read-only; + }; + + MIBIB@10000 { + label = "MIBIB"; + reg = <0x10000 0x20000>; + read-only; + }; + + SBL2@30000 { + label = "SBL2"; + reg = <0x30000 0x30000>; + read-only; + }; + + SBL3@60000 { + label = "SBL3"; + reg = <0x60000 0x30000>; + read-only; + }; + + DDRCONFIG@90000 { + label = "DDRCONFIG"; + reg = <0x90000 0x10000>; + read-only; + }; + + SSD@a0000 { + label = "SSD"; + reg = <0xa0000 0x10000>; + read-only; + }; + + TZ@b0000 { + label = "TZ"; + reg = <0xb0000 0x30000>; + read-only; + }; + + RPM@e0000 { + label = "RPM"; + reg = <0xe0000 0x20000>; + read-only; + }; + + APPSBL@100000 { + label = "APPSBL"; + reg = <0x100000 0x70000>; + read-only; + }; + + APPSBLENV@170000 { + label = "APPSBLENV"; + reg = <0x170000 0x10000>; + read-only; + }; + + ART: ART@180000 { + label = "ART"; + reg = <0x180000 0x40000>; + read-only; + }; + + BOOTCONFIG@1c0000 { + label = "BOOTCONFIG"; + reg = <0x1c0000 0x10000>; + read-only; + }; + + APPSBL_1@1d0000 { + label = "APPSBL_1"; + reg = <0x1d0000 0x70000>; + read-only; + }; + }; + }; + }; +}; + +&hs_phy_0 { /* USB3 port 0 HS phy */ + status = "okay"; +}; + +&ss_phy_0 { /* USB3 port 0 SS phy */ + status = "okay"; +}; + +&hs_phy_1 { /* USB3 port 1 HS phy */ + status = "okay"; +}; + +&ss_phy_1 { /* USB3 port 1 SS phy */ + status = "okay"; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; +}; + +&dwc3_0 { + #address-cells = <1>; + #size-cells = <0>; + + hub_port0: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&dwc3_1 { + #address-cells = <1>; + #size-cells = <0>; + + hub_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + force_gen1 = <1>; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57", + "gpio58", "gpio64", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22", + "gpio23", "gpio24", "gpio25", "gpio26", "gpio53"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + uart0_pins: uart0_pins { + mux { + pins = "gpio10", "gpio11"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs{ + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + + pullups { + pins = "gpio39"; + bias-pull-up; + }; + + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + + usb_pwr_en_pins: usb_pwr_en_pins { + mux{ + pins = "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + output-high; + }; + }; +};
\ No newline at end of file diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi index d38fc29b68..08b8e003a8 100644 --- a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -972,7 +972,7 @@ status = "disabled"; - dwc3@11000000 { + dwc3_0: dwc3@11000000 { compatible = "snps,dwc3"; reg = <0x11000000 0xcd00>; interrupts = <0 110 0x4>; @@ -997,7 +997,7 @@ status = "disabled"; - dwc3@10000000 { + dwc3_1: dwc3@10000000 { compatible = "snps,dwc3"; reg = <0x10000000 0xcd00>; interrupts = <0 205 0x4>; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index 6109765041..e1eb090de3 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -3,6 +3,13 @@ include $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/image.mk +define Build/buffalo-rootfs-cksum + ( \ + echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \ + $(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \ + ) >> $@ +endef + define Device/Default PROFILES := Default KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts) @@ -72,6 +79,21 @@ define Device/ZyXELImage IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata endef +define Device/buffalo_wxr-2533dhp + $(call Device/LegacyImage) + DEVICE_DTS := qcom-ipq8064-wxr-2533dhp + DEVICE_TITLE := Buffalo WXR-2533DHP + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + KERNEL_IN_UBI := 1 + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \ + sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct +endef +TARGET_DEVICES += buffalo_wxr-2533dhp + define Device/compex_wpq864 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch index 0a62a0bc84..e11378b42a 100644 --- a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -699,6 +699,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -699,6 +699,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8084-mtp.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ qcom-ipq8064-ap148.dtb \ @@ -23,6 +23,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq8064-r7500v2.dtb \ + qcom-ipq8064-wg2600hp.dtb \ + qcom-ipq8064-wpq864.dtb \ ++ qcom-ipq8064-wxr-2533dhp.dtb \ + qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ qcom-msm8660-surf.dtb \ |