ramips: add support for TP-Link TL-WR902AC v3

TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router
based on MediaTek MT7628N + MT7650E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet

* MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment.
  Therefore 5Ghz won' work.

Flash instruction:

The only way to flash LEDE image in TL-WR902AC v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>

6 files changed, 128 insertions, 0 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index b068e62e87..4b8242cb9f 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -414,6 +414,11 @@ tplink,tl-mr3420-v5)
 	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
 	;;
+tplink,tl-wr902ac-v3)
+	set_usb_led "$boardname:green:usb"
+	ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan" "wlan0"
+	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x10"
+	;;
 u25awf-h1)
 	set_wifi_led "u25awf:red:wifi"
 	ucidef_set_led_netdev "eth" "eth" "u25awf:green:lan" "eth0"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index d20b0aa1aa..03f718ee30 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -320,6 +320,10 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
 		;;
+	tplink,tl-wr902ac-v3)
+		ucidef_add_switch "switch0" \
+			"4:lan" "6@eth0"
+		;;
 	vonets,var11n-300|\
 	wt1520-4M|\
 	wt1520-8M)
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 2dcc75a019..d9f131b2a8 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -41,6 +41,7 @@ get_status_led() {
 	tplink,c20-v4|\
 	tplink,c50-v3|\
 	tplink,tl-mr3420-v5|\
+	tplink,tl-wr902ac-v3|\
 	tl-wr840n-v4|\
 	tl-wr840n-v5|\
 	tl-wr841n-v13|\
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index e6489a2b58..b052cf8625 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -250,6 +250,7 @@ platform_check_image() {
 	tplink,c20-v4|\
 	tplink,c50-v3|\
 	tplink,tl-mr3420-v5|\
+	tplink,tl-wr902ac-v3|\
 	tl-wr840n-v4|\
 	tl-wr840n-v5|\
 	tl-wr841n-v13)
diff --git a/target/linux/ramips/dts/TL-WR902ACV3.dts b/target/linux/ramips/dts/TL-WR902ACV3.dts
new file mode 100644
index 0000000000..8ff3576595
--- /dev/null
+++ b/target/linux/ramips/dts/TL-WR902ACV3.dts
@@ -0,0 +1,102 @@
+/dts-v1/;
+
+#include "TPLINK-8M.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "tplink,tl-wr902ac-v3", "mediatek,mt7628an-soc";
+	model = "TP-Link TL-WR902AC v3";
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+
+		reset {
+			label = "reset";
+			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		sw1 {
+			label = "sw1";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		sw2 {
+			label = "sw2";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_1>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		lan {
+			label = "tl-wr902ac-v3:green:lan";
+			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		power {
+			label = "tl-wr902ac-v3:green:power";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		usb {
+			label = "tl-wr902ac-v3:green:usb";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		wan {
+			label = "tl-wr902ac-v3:green:wan";
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "tl-wr902ac-v3:green:wlan";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "tl-wr902ac-v3:green:wps";
+			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pinctrl {
+	state_default: pinctrl0 {
+		gpio {
+			ralink,group = "i2c", "i2s", "p0led_an", "p4led_an", "uart1", "wdt", "wled_an";
+			ralink,function = "gpio";
+		};
+	};
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+
+	pcie-bridge {
+		mt76@1,0 {
+			reg = <0x0000 0 0 0 0>;
+			device_type = "pci";
+			mediatek,mtd-eeprom = <&factory 0x28000>;
+			ieee80211-freq-limit = <5000000 6000000>;
+			mtd-mac-address = <&factory 0xf100>;
+			mtd-mac-address-increment = <(-1)>;
+		};
+	};
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index bcee98ef45..4362c3bc43 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -196,6 +196,21 @@ define Device/tplink_tl-mr3420-v5
 endef
 TARGET_DEVICES += tplink_tl-mr3420-v5
 
+define Device/tplink_tl-wr902ac-v3
+  $(Device/tplink)
+  DTS := TL-WR902ACV3
+  IMAGE_SIZE := 7808k
+  DEVICE_TITLE := TP-Link TL-WR902AC v3
+  TPLINK_FLASHLAYOUT := 8Mmtk
+  TPLINK_HWID := 0x000dc88f
+  TPLINK_HWREV := 0x89
+  TPLINK_HWREVADD := 0x1
+  TPLINK_HVERSION := 3
+  IMAGES += factory.bin
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += tplink_tl-wr902ac-v3
+
 define Device/u7628-01-128M-16M
   DTS := U7628-01-128M-16M
   IMAGE_SIZE := 16064k