ipq40xx: add support for Buffalo WTR-M2133HP

Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>

7 files changed, 451 insertions, 0 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index cd336a9e6a..61d02a17bc 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -65,6 +65,11 @@ ipq40xx_setup_interfaces()
 	engenius,eap2200)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
+	buffalo,wtr-m2133hp)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		ucidef_add_switch "switch0" \
+			"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
+		;;
 	cellc,rtl30vw)
 		ucidef_set_interface_lan "eth0"
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index b95bab7cae..8df7990f2e 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -31,6 +31,10 @@ case "$FIRMWARE" in
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
+	buffalo,wtr-m2133hp)
+		caldata_extract "ART" 0x9000 0x2f20
+		ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
+		;;
 	engenius,eap2200 |\
 	openmesh,a62)
 		caldata_extract "0:ART" 0x9000 0x2f20
@@ -82,6 +86,10 @@ case "$FIRMWARE" in
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
+	buffalo,wtr-m2133hp)
+		caldata_extract "ART" 0x1000 0x2f20
+		ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x26)
+		;;
 	cellc,rtl30vw |\
 	compex,wpj419 |\
 	compex,wpj428 |\
@@ -171,6 +179,10 @@ case "$FIRMWARE" in
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
+	buffalo,wtr-m2133hp)
+		caldata_extract "ART" 0x5000 0x2f20
+		ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x2c)
+		;;
 	cellc,rtl30vw |\
 	compex,wpj419 |\
 	compex,wpj428 |\
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 2abff3bd00..5b89710a22 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -64,6 +64,7 @@ platform_do_upgrade() {
 	avm,fritzbox-7530 |\
 	avm,fritzrepeater-1200 |\
 	avm,fritzrepeater-3000 |\
+	buffalo,wtr-m2133hp |\
 	cilab,meshpoint-one |\
 	engenius,eap2200 |\
 	mobipromo,cm520-79f |\
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts
new file mode 100644
index 0000000000..1977358525
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts
@@ -0,0 +1,419 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Copyright (c) 2015 - 2016, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020 Yanase Yuki <dev@zpc.sakura.ne.jp>
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "Buffalo WTR-M2133HP";
+	compatible = "buffalo,wtr-m2133hp", "qcom,ipq4019";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	chosen {
+		/*
+		 * U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs" to
+		 * kernel command line. But we use different partition names,
+		 * so we have to set correct parameters.
+		 */
+		bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
+	};
+
+	aliases {
+		led-boot = &led_power_blue;
+		led-failsafe = &led_power_orange;
+		led-running = &led_power_white;
+		led-upgrade = &led_power_blue;
+		label-mac-device = &gmac0;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+			status = "okay";
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+			switch_lan_bmp = <0x1c>;
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+
+		usb3@8af8800 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power_white: power_white {
+			label = "wtr-m2133hp:white:power";
+			gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_power_orange: power_orange {
+			label = "wtr-m2133hp:orange:power";
+			gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_power_blue: power_blue {
+			label = "wtr-m2133hp:blue:power";
+			gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+		};
+
+		router_white {
+			label = "wtr-m2133hp:white:router";
+			gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+		};
+
+		router_orange {
+			label = "wtr-m2133hp:orange:router";
+			gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+		};
+
+		internet_white {
+			label = "wtr-m2133hp:white:internet";
+			gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
+		};
+
+		internet_orange {
+			label = "wtr-m2133hp:orange:internet";
+			gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+		};
+
+		wireless_white {
+			label = "wtr-m2133hp:white:wireless";
+			gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		wireless_orange {
+			label = "wtr-m2133hp:orange:wireless";
+			gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		auto_mode {
+			label = "auto_mode";
+			gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+
+		router_mode {
+			label = "router_mode";
+			gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
+		};
+
+		ap_mode {
+			label = "ap_mode";
+			gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_2>;
+			linux,input-type = <EV_SW>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "AOSS Button";
+			gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+};
+
+&tlmm {
+	serial_0_pins: serial0_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio6";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio7";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	nand_pins: nand_pins {
+		pullups {
+			pins = "gpio52", "gpio53", "gpio58",
+				"gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56",
+				"gpio57", "gpio60", "gpio61",
+				"gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67",
+				"gpio68", "gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+
+	usb_power {
+		line-name = "USB power";
+		gpios = <34 GPIO_ACTIVE_HIGH>;
+		gpio-hog;
+		output-high;
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@0,0 {
+			compatible = "qcom,ath10k";
+			reg = <0 0 0 0 0>;
+
+			qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
+		};
+	};
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x0000000 0x0100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "MIBIB";
+				reg = <0x0100000 0x0100000>;
+				read-only;
+			};
+
+			partition@200000 {
+				label = "BOOTCONFIG";
+				reg = <0x0200000 0x0100000>;
+				read-only;
+			};
+
+			partition@300000 {
+				label = "QSEE";
+				reg = <0x0300000 0x0100000>;
+				read-only;
+			};
+
+			partition@400000 {
+				label = "QSEE_1";
+				reg = <0x0400000 0x0100000>;
+				read-only;
+			};
+
+			partition@500000 {
+				label = "CDT";
+				reg = <0x0500000 0x0080000>;
+				read-only;
+			};
+
+			partition@580000 {
+				label = "CDT_1";
+				reg = <0x0580000 0x0080000>;
+				read-only;
+			};
+
+			partition@600000 {
+				label = "BOOTCONFIG1";
+				reg = <0x0600000 0x0080000>;
+				read-only;
+			};
+
+			partition@680000 {
+				label = "APPSBLENV";
+				reg = <0x0680000 0x0080000>;
+			};
+
+			partition@700000 {
+				label = "APPSBL";
+				reg = <0x0700000 0x0200000>;
+				read-only;
+			};
+
+			partition@900000 {
+				label = "APPSBL_1";
+				reg = <0x0900000 0x0200000>;
+				read-only;
+			};
+
+			art: partition@b00000 {
+				label = "ART";
+				reg = <0x0b00000 0x0080000>;
+				read-only;
+			};
+
+			partition@b80000 {
+				label = "ART_1";
+				reg = <0x0b80000 0x0080000>;
+				read-only;
+			};
+
+			orgdata: partition@c00000 {
+				label = "ORGDATA";
+				reg = <0x0c00000 0x0080000>;
+				read-only;
+			};
+
+			partition@c80000 {
+				label = "ORGDATA_1";
+				reg = <0x0c80000 0x0080000>;
+				read-only;
+			};
+
+			partition@d00000 {
+				label = "ubi";
+				reg = <0x0d00000 0x2900000>;
+			};
+
+			partition@3600000 {
+				label = "rootfs_recover";
+				reg = <0x3600000 0x2900000>;
+				read-only;
+			};
+
+			partition@5f00000 {
+				label = "user_property";
+				reg = <0x5f00000 0x1a20000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
+	ieee80211-freq-limit = <2400000 2483000>;
+};
+
+&wifi1 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
+};
+
+&mdio {
+	status = "okay";
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+};
+
+&gmac0 {
+	mtd-mac-address = <&orgdata 0x20>;
+};
+
+&gmac1 {
+	mtd-mac-address = <&orgdata 0x20>;
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 5336649c3d..51e8bcc7e3 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -245,6 +245,18 @@ define Device/avm_fritzrepeater-3000
 endef
 TARGET_DEVICES += avm_fritzrepeater-3000
 
+define Device/buffalo_wtr-m2133hp
+	$(call Device/FitImage)
+	$(call Device/UbiFit)
+	DEVICE_VENDOR := Buffalo
+	DEVICE_MODEL := WTR-M2133HP
+	SOC := qcom-ipq4019
+	DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9984-ct ipq-wifi-buffalo_wtr-m2133hp
+	BLOCKSIZE := 128k
+	PAGESIZE := 2048
+endef
+TARGET_DEVICES += buffalo_wtr-m2133hp
+
 define Device/cellc_rtl30vw
 	KERNEL_SUFFIX := -fit-uImage.itb
 	KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index fb358ed184..924715c9aa 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -49,6 +49,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-rtl30vw.dtb \
 +	qcom-ipq4019-u4019-32m.dtb \
 +	qcom-ipq4019-wpj419.dtb \
++	qcom-ipq4019-wtr-m2133hp.dtb \
 +	qcom-ipq4028-wpj428.dtb \
 +	qcom-ipq4029-ap-303.dtb \
 +	qcom-ipq4029-ap-303h.dtb \
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 2db36aa597..c5b0981f49 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -50,6 +50,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-rtl30vw.dtb \
 +	qcom-ipq4019-u4019-32m.dtb \
 +	qcom-ipq4019-wpj419.dtb \
++	qcom-ipq4019-wtr-m2133hp.dtb \
 +	qcom-ipq4028-wpj428.dtb \
 +	qcom-ipq4029-ap-303.dtb \
 +	qcom-ipq4029-ap-303h.dtb \