ipq40xx: add support for AVM FRITZ!Repeater 3000

Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH:   Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED:    - Connect green/blue/red
        - Power green
BTN:   WPS/Connect
UART:  115200n8 3.3V
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ3000.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz3000.bin uboot0
   > mtd write /path/to/uboot-fritz3000.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>

3 files changed, 10 insertions, 2 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 94fb26ce48..02cdd30b56 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -37,6 +37,7 @@ ipq40xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;
+	avm,fritzrepeater-3000|\
 	compex,wpj428)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 1264d2ef36..8520dfb41d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -111,6 +111,10 @@ case "$FIRMWARE" in
 		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
 			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
 		;;
+	avm,fritzrepeater-3000)
+		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+		;;
 	openmesh,a62)
 		ath10kcal_extract "0:ART" 36864 12064
 		;;
@@ -135,7 +139,8 @@ case "$FIRMWARE" in
 	avm,fritzbox-4040)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
 		;;
-	avm,fritzbox-7530)
+	avm,fritzbox-7530 |\
+	avm,fritzrepeater-3000)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
@@ -183,7 +188,8 @@ case "$FIRMWARE" in
 	avm,fritzbox-4040)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
 		;;
-	avm,fritzbox-7530)
+	avm,fritzbox-7530 |\
+	avm,fritzrepeater-3000)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 9a2c13cf4d..84b123335c 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -49,6 +49,7 @@ platform_do_upgrade() {
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	avm,fritzbox-7530 |\
+	avm,fritzrepeater-3000|\
 	qxwlan,e2600ac-c2)
 		nand_do_upgrade "$ARGV"
 		;;