strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8653 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 512 insertions, 0 deletions

diff --git a/target/linux/etrax/image/boot_linux b/target/linux/etrax/image/boot_linux
new file mode 100755
index 0000000000..e7d5807f53
--- /dev/null
+++ b/target/linux/etrax/image/boot_linux
@@ -0,0 +1,512 @@
+#!/usr/bin/perl -w
+
+#*****************************************************************************
+#!
+#! FILE NAME  : boot_linux
+#!
+#! PARAMETERS : -b <bootimage>     the name of the boot image to use
+#!              -d <device>        the interface to use, e.g., eth1
+#!                                 (defaults is eth0)
+#!              -f                 save it in flash memory at address 0x10000
+#!              -F                 save it in flash memory at address 0
+#!              -h                 show some help
+#!              -i <image>         name of the image to use (default is fimage)
+#!              -o <offset>        the offset in the flash where the flashing
+#!                                 starts
+#!              -O <offset>        the offset in the image file where the
+#!                                 flashing starts from
+#!              -p                 print the resulting etrax100boot command
+#!                                 instead of executing it
+#!              -s <size>          how much to flash (default is the size of
+#!                                 the flash minus the offset specified using
+#!                                 -o or -f)
+#!              -S <size>          the size of the flash
+#!
+#!              All sizes and offsets above can be specified as decimal
+#!              numbers, or as hexadecimal numbers by prefixing them with 0x.
+#!              It is also possible to use the suffixes k and M to specify
+#!              kilo (1024) or mega (1048576).
+#!
+#! DESCRIPTION: Extract the start of the image and any registers that should
+#!              be set from the kimage or fimage file, and then boot it.
+#!
+#! FUNCTIONS  : convert_size
+#!              extract_hw_settings
+#!              get_dword
+#!              calculate_sdram_init
+#!              sdram_command
+#!              print_help
+#!
+#!----------------------------------------------------------------------------
+#! HISTORY
+#!
+#! $Log: boot_linux,v $
+#! Revision 1.16  2004/11/01 16:32:27  starvik
+#! Corrected help text to avoid confusion
+#!
+#! Revision 1.15  2003/01/29 11:48:57  pkj
+#! Calculate a flash size large enough for the given image if the
+#! -S option is not specified.
+#!
+#! Revision 1.14  2002/11/18 14:40:09  pkj
+#! Make use of the --loop option to etrax100boot when initialising
+#! SDRAM memories. This requires a lot fewer options to be passed
+#! to the boot loader.
+#!
+#! Revision 1.13  2002/08/15 16:29:02  pkj
+#! * The -S option now accepts the size in bytes (just like the -s option).
+#!   For backwards compatibility it still assumes sizes of 16 and less to
+#!   be specified in MB.
+#! * The suffixes k and M can now be used with all sizes and offsets to
+#!   specify them in kilo or mega.
+#!
+#! Revision 1.12  2002/08/15 15:27:34  pkj
+#! Use $opts{'x'} instead of $opt_x.
+#!
+#! Revision 1.11  2002/07/04 17:06:39  pkj
+#! * No longer specifies a bootfile by default (not needed any longer).
+#! * Implemented option -b to specify a bootfile.
+#! * Removed references to option -l (it was never implemented).
+#!
+#! Revision 1.10  2002/06/04 11:50:23  starvik
+#! Check if mrs_data is specified in kernelconfig (necessary for MCM)
+#!
+#! Revision 1.9  2002/01/29 10:38:26  pkj
+#! Change illegal to invalid.
+#!
+#! Revision 1.8  2001/09/13 12:32:10  pkj
+#! * Added option -S to specify the size of the flash (in MB),  as -s
+#!   is used to specify how much to flash nowadays.
+#! * Made the default size of the flash depend on the size of the image
+#!   file. If it is bigger than 0x200100 then the flash is assumed to
+#!   be 4 MB, otherwise it is assumed to be 2 MB.
+#! * Added verification of various options.
+#!
+#! Revision 1.7  2001/09/13 10:25:11  pkj
+#! Minor clean-up.
+#!
+#! Revision 1.6  2001/06/29 10:05:16  pkj
+#! Corrected check for SDRAM.
+#!
+#! Revision 1.5  2001/06/29 09:11:55  pkj
+#! Synchronised boot_elinux and boot_linux.
+#!
+#!----------------------------------------------------------------------------
+#! (C) Copyright 2001, Axis Communications AB, LUND, SWEDEN
+#!****************************************************************************
+# $Id: boot_linux,v 1.16 2004/11/01 16:32:27 starvik Exp $
+
+#****************** INCLUDE FILES SECTION ************************************
+
+use strict;
+
+use Getopt::Std;
+use File::Basename;
+
+#****************** VARIABLE DECLARATION SECTION *****************************
+
+use vars qw($my_name %opts);
+use vars qw($text_start $cmd);
+use vars qw($image_name $image_size);
+use vars qw($offset $source_offset $flash_size $flashing_size);
+use vars qw($sdram_timing_address $sdram_config_address);
+use vars qw($sdram_precharge $sdram_nop $sdram_refresh $sdram_mrs);
+
+#****************** CONSTANT SECTION *****************************************
+
+# Register addresses
+$sdram_timing_address = "b0000008";
+$sdram_config_address = "b000000c";
+
+# SDRAM commands
+$sdram_precharge = 3;
+$sdram_nop = 0;
+$sdram_refresh = 2;
+$sdram_mrs = 1;
+
+#****************** MAIN PROGRAM SECTION *************************************
+
+# The name of this program.
+$my_name = basename($0);
+
+# Get options
+getopts('b:d:fFhi:o:O:ps:S:', \%opts);
+
+&print_help if ($opts{'h'});
+
+# Name and existance of the image
+$image_name = ($opts{'i'} ? $opts{'i'} : 'fimage');
+die "Could not find the image $image_name!\n" unless (-s $image_name);
+
+if ($opts{'f'} || $opts{'F'})
+{
+  $image_size = -s $image_name;
+
+  $offset = ($opts{'f'} ? 0x10000 : 0);
+
+  $offset = &convert_size($opts{'o'}) if (defined($opts{'o'}));
+
+  die("$my_name: Invalid destination offset\n") if ($offset !~ /^\d+$/);
+
+  my $base_name = basename($image_name);
+  if ($base_name eq 'timage' || $base_name eq 'flash1.img')
+  {
+    $source_offset = 0;
+  }
+  else
+  {
+    $source_offset = $offset;
+  }
+
+  $source_offset = &convert_size($opts{'O'}) if (defined($opts{'O'}));
+
+  die("$my_name: Invalid source offset\n") if ($source_offset !~ /^\d+$/);
+  die("$my_name: Source offset > image size\n") if ($source_offset > $image_size);
+
+  if (defined($opts{'S'}))
+  {
+    # Backwards compatibility to allow specifying the flash size in MB
+    # without using an M suffix
+    $opts{'S'} .= 'M' if ($opts{'S'} =~ /^\d+$/ && $opts{'S'} <= 16);
+
+    $flash_size = &convert_size($opts{'S'});
+  }
+  else
+  {
+    # Calculate a flash size large enough for the image without the checksum
+    # and HWID.
+    $flash_size = ($image_size - $source_offset + $offset) & 0xFFFF0000;
+  }
+
+  die("$my_name: Invalid flash size\n") if ($flash_size !~ /^\d+$/);
+  die("$my_name: Destination offset > flash size\n") if ($offset > $flash_size);
+  if (defined($opts{'s'}))
+  {
+    $flashing_size = &convert_size($opts{'s'});
+  }
+  else
+  {
+    $flashing_size = $flash_size - $offset;
+  }
+
+  die("$my_name: Invalid size to flash\n") if ($flashing_size !~ /^\d+$/);
+
+  if ($flashing_size > $flash_size - $offset)
+  {
+    $flashing_size = $flash_size - $offset;
+    printf("Warning: Flashing size limited to 0x%lx due to the offset (0x%lx) and flash size (0x%lx).\n", $flashing_size, $offset, $flash_size);
+  }
+
+  if ($flashing_size > $image_size - $source_offset)
+  {
+    $flashing_size = $image_size - $source_offset;
+    printf("Warning: Flashing size limited to 0x%lx due to the offset (0x%lx) and image size (0x%lx).\n", $flashing_size, $source_offset, $image_size);
+  }
+}
+
+# Create the command line to boot the image
+if (system('./etrax100boot --help > /dev/null') == 0)
+{
+  $cmd = './etrax100boot';
+}
+elsif (system('svinto_boot --help > /dev/null') == 0)
+{
+  $cmd = 'svinto_boot';
+}
+else
+{
+  die("Cannot find e100boot program in your PATH!\n");
+}
+
+$cmd .= " --device $opts{'d'}" if ($opts{'d'});
+
+$cmd .= &extract_hw_settings;
+
+$cmd .= " --bootfile $opts{'b'}" if ($opts{'b'});
+$cmd .= " --file $image_name $text_start";
+
+if ($opts{'f'} || $opts{'F'})
+{
+  $cmd .= sprintf(" --flash %lx %lx %lx --jump 0",
+		  hex($text_start) + $source_offset, $offset, $flashing_size);
+}
+else
+{
+  $cmd .= " --jump $text_start";
+}
+
+if ($opts{'p'})
+{
+  print "Command:\n$cmd\n";
+}
+else
+{
+  system($cmd);
+}
+
+exit 0;
+
+#****************** FUNCTION DEFINITION SECTION ******************************
+
+#*****************************************************************************
+##
+## FUNCTION NAME: convert_size
+##
+##****************************************************************************
+
+sub convert_size
+{
+  my($arg) = @_;
+  my $size;
+
+  if ($arg =~ /^0x([\da-fA-F]+)([kM])?$/)
+  {
+    $size = hex($1);
+  }
+  elsif ($arg =~ /^(\d+)([kM])?$/)
+  {
+    $size = $1;
+  }
+  else
+  {
+    return -1;
+  }
+
+  if (!defined($2))
+  {
+    return $size;
+  }
+  elsif ($2 eq 'k')
+  {
+    return $size * 1024;
+  }
+  elsif ($2 eq 'M')
+  {
+    return $size * 1048576;
+  }
+}
+
+#*****************************************************************************
+##
+## FUNCTION NAME: extract_hw_settings
+##
+##****************************************************************************
+
+sub extract_hw_settings
+{
+  my $data;
+  my $dbg_port;
+  my $sdram_enabled;
+  my $return_value = "";
+  my $sdram_config;
+
+  # The hw information table has the following format
+  #
+  # "HW_PARAM_MAGIC"
+  # text_start (dword)
+  # serial debg port (dword)
+  # sdram enabled (dword)
+  # register address (dword)
+  # register value (dword)
+  # ...
+  # 0
+
+  open(FILE, "$image_name") || die("Could not open '$image_name'");
+
+  while (<FILE>)
+  {
+    if (m/HW_PARAM_MAGIC/g)
+    {
+      # Seek to first byte after magic
+      seek(FILE, -length($_) + pos($_), 1);
+      last;
+    }
+  }
+
+  $text_start = &get_dword;
+  $dbg_port = &get_dword;
+  $sdram_enabled = int(&get_dword);
+
+  while (1)
+  {
+    my $register = &get_dword;
+    my $value = &get_dword;
+
+    last if ($register eq "00000000");
+
+    if ($sdram_enabled)
+    {
+      if ($register eq $sdram_config_address)
+      {
+	$sdram_config = $value;
+      }
+      elsif ($register eq $sdram_timing_address)
+      {
+	$return_value .= &calculate_sdram_init($value, $sdram_config);
+	next;
+      }
+    }
+
+    $return_value .= " --setreg $register $value";
+  }
+
+  close(FILE);
+
+  return $return_value;
+}
+
+#*****************************************************************************
+##
+## FUNCTION NAME: get_dword
+##
+##****************************************************************************
+
+sub get_dword
+{
+  my $data;
+
+  read(FILE, $data, 4);
+  return unpack("H8", pack("V", unpack("N", $data)));
+}
+
+#*****************************************************************************
+##
+## FUNCTION NAME: calculate_sdram_init
+##
+##****************************************************************************
+
+sub calculate_sdram_init
+{
+  # Refer to ETRAX 100LX Designers Reference for a description of SDRAM
+  # initialization
+  my $sdram_init_val = hex($_[0]);
+  my $sdram_config_val = hex($_[1]);
+  my $bus_width = $sdram_config_val & 0x00800000;
+  my $speed;
+  my $cas_latency;
+  my $mrs_data;
+  my $temp;
+  my $return_value;
+  my $value;
+
+  $mrs_data = ($sdram_init_val & 0x00ff0000) >> 16;
+  $sdram_init_val &= 0x8000ffff; # Make sure mrs data is 0
+  $sdram_init_val |= 0x80000000; # Make sure sdram is enabled
+  $speed = $sdram_init_val & 0x1000;
+  $cas_latency = $sdram_init_val & 0x3;
+  if ($speed) # 100 MHz
+  {
+    $cas_latency += 2;
+  }
+  else # 50 MHz
+  {
+    $cas_latency += 1;
+  }
+
+  # Calculate value of mrs_data
+  # CAS latency = 2 && bus_width = 32 => 0x40
+  # CAS latency = 3 && bus_width = 32 => 0x60
+  # CAS latency = 2 && bus_width = 16 => 0x20
+  # CAS latency = 3 && bus_width = 16 => 0x30
+  if ($mrs_data == 0)
+  {
+    if ($bus_width == 0) # 16 bits
+    {
+      $mrs_data = $cas_latency == 2 ? 0x20 : 0x30;
+    }
+    else # 32 bits
+    {
+      $mrs_data = $cas_latency == 2 ? 0x40 : 0x60;
+    }
+  }
+
+  $temp = $sdram_init_val | 0x0000c000; # Disable refresh
+  $return_value .= &sdram_command($temp);
+  $return_value .= " --pause 20000";
+
+  $return_value .= &sdram_command($temp, $sdram_precharge);
+  $return_value .= &sdram_command($temp, $sdram_nop);
+
+  $return_value .= " --setreg +0 7";
+  $return_value .= " --label label1";
+  $return_value .= &sdram_command($temp, $sdram_refresh);
+  $return_value .= &sdram_command($temp, $sdram_nop);
+  $return_value .= " --loop +0 label1";
+
+  $return_value .= &sdram_command($temp, $sdram_mrs, $mrs_data);
+  $return_value .= &sdram_command($temp, $sdram_nop);
+
+  $return_value .= &sdram_command($sdram_init_val);
+
+  return $return_value;
+}
+
+#*****************************************************************************
+##
+## FUNCTION NAME: sdram_command
+##
+##****************************************************************************
+
+sub sdram_command
+{
+  my($temp, $value, $mrs_data) = @_;
+
+  $value ||= 0;
+  if ($value == $sdram_mrs)
+  {
+    $value = sprintf("%lx", $temp | ($value << 9) | ($mrs_data << 16));
+  }
+  else
+  {
+    $value = sprintf("%lx", $temp | ($value << 9));
+  }
+
+  return " --setreg $sdram_timing_address $value";
+}
+
+#*****************************************************************************
+##
+## FUNCTION NAME: print_help
+##
+##****************************************************************************
+
+sub print_help
+{
+  print "\nAXIS $my_name, ", '$Revision: 1.16 $ $Date: 2004/11/01 16:32:27 $ ', "\n";
+  die <<EOT;
+Copyright (C) 2001-2002 Axis Communications AB
+
+DESCRIPTION:
+  This program is used to boot (and flash) a linux image to a box.
+  It tries to extract the required ETRAX 100 settings from the image file.
+
+SYNTAX:
+  $my_name [options]
+
+OPTIONS:
+  -b <bootfile>           : The boot image to use.
+  -d <device>             : The network interface to use, default is eth0.
+  -f                      : Save the image in the flash memory starting at
+                            address 0x10000.
+  -F                      : Save the image in the flash memory starting at
+                            address 0.
+  -h                      : Print this help text.
+  -i <image>              : The path and name of the image to use, default
+                            is fimage.
+  -o <offset>             : The offset in the flash where the flashing starts.
+  -O <offset>             : The offset in the image file where the flashing
+                            starts from.
+  -p                      : Print the resulting etrax100boot command instead
+                            of executing it.
+  -s <size>               : How much to flash (default is the size of the
+			    flash minus the offset specified using -o or -f).
+  -S <size>               : The size of the flash.
+
+  All sizes and offsets above can be specified as decimal numbers, or as
+  hexadecimal numbers by prefixing them with 0x. It is also possible to use
+  the suffixes k and M to specify kilo (1024) or mega (1048576).
+
+EOT
+}
+
+#****************** END OF FILE boot_linux ***********************************