ath79: support for TP-Link EAP225 v3

TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
      Do NOT bridge R230.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:

    Using interface ath0 with hwaddr b0:...:3e and ssid "..."
    Using interface ath10 with hwaddr b0:...:3f and ssid "..."

Tested by forum user blinkstar88

Signed-off-by: Sander Vanheule <sander@svanheule.net>

1 files changed, 30 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts
new file mode 100644
index 0000000000..3d4950eaf0
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_tplink_eap2x5-1port.dtsi"
+
+/ {
+	compatible = "tplink,eap225-v3", "qca,qca9563";
+	model = "TP-Link EAP225 v3";
+
+	aliases {
+		led-boot = &led_status_green;
+		led-failsafe = &led_status_amber;
+		led-running = &led_status_green;
+		led-upgrade = &led_status_amber;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_green: status_green {
+			label = "green:status";
+			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led_status_amber: status_amber {
+			label = "amber:status";
+			gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};