ath79: add support for GL.iNet GL-MiFi

Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.

Specifications:
 - Atheros AR9331
 - 64 MB of RAM
 - 16 MB of FLASH (SPI NOR)
 - 2x 10/100/1000 Mbps Ethernet
 - 2.4GHz (AR9330), 802.11b/g/n
 - 1x USB 2.0 (vbus driven by GPIO)
 - 4x LED, driven by GPIO
 - 1x button (reset)
 - 1x mini pci-e slot (vcc driven by GPIO)

Flash instructions:

Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.

Note on MAC addresses:

Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.

Note on GPIOs:

In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.

Acknowledgements:

This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.

[1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

4 files changed, 169 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/ar9331_glinet_gl-mifi.dts b/target/linux/ath79/dts/ar9331_glinet_gl-mifi.dts
new file mode 100644
index 0000000000..e969007fc0
--- /dev/null
+++ b/target/linux/ath79/dts/ar9331_glinet_gl-mifi.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9331.dtsi"
+
+/ {
+	compatible = "glinet,gl-mifi", "qca,ar9331";
+	model = "GL.iNet GL-MiFi";
+
+	aliases {
+		serial0 = &uart;
+		label-mac-device = &eth0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan {
+			label = "gl-mifi:green:wlan";
+			gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		lan {
+			label = "gl-mifi:green:lan";
+			gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			label = "gl-mifi:green:wan";
+			gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
+		};
+
+		3g4g {
+			label = "gl-mifi:green:3g4g";
+			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+			debounce-interval = <60>;
+		};
+	};
+
+	reg_usb_vbus: reg_usb_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio 6 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-export {
+		compatible = "gpio-export";
+
+		minipcie {
+			gpio-export,name = "minipcie";
+			gpio-export,output = <0>;
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+
+	dr_mode = "host";
+	vbus-supply = <&reg_usb_vbus>;
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+
+	num-chipselects = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <33000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0xfa0000>;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x0>;
+
+	gmac-config {
+		device = <&gmac>;
+
+		switch-phy-addr-swap = <0>;
+		switch-phy-swap = <0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x0>;
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 2bd70aae31..f3e3b758b5 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -153,6 +153,10 @@ glinet,gl-ar300m-lite)
 glinet,gl-ar300m16)
 	ucidef_set_led_netdev "lan" "LAN" "gl-ar300m:green:lan" "eth0"
 	;;
+glinet,gl-mifi)
+	ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x02"
+	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
+	;;
 glinet,gl-x750)
 	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
 	;;
diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration b/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration
index 1c7ecba5f8..757b0c9974 100644
--- a/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration
+++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/04_led_migration
@@ -8,6 +8,9 @@ case "$board" in
 engenius,epg5000)
 	migrate_leds ":wlan-2g=:wlan2g" ":wlan-5g=:wlan5g"
 	;;
+glinet,gl-mifi)
+	migrate_leds ":net=:3g4g"
+	;;
 tplink,archer-c25-v1|\
 tplink,archer-c58-v1|\
 tplink,archer-c59-v1|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 5ef6104ef6..0e7efa32af 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -821,6 +821,16 @@ define Device/glinet_gl-ar750
 endef
 TARGET_DEVICES += glinet_gl-ar750
 
+define Device/glinet_gl-mifi
+  SOC := ar9331
+  DEVICE_VENDOR := GL.iNET
+  DEVICE_MODEL := GL-MiFi
+  DEVICE_PACKAGES := kmod-usb-chipidea2
+  IMAGE_SIZE := 16000k
+  SUPPORTED_DEVICES += gl-mifi
+endef
+TARGET_DEVICES += glinet_gl-mifi
+
 define Device/glinet_gl-x750
   SOC := qca9531
   DEVICE_VENDOR := GL.iNet