aboutsummaryrefslogtreecommitdiffstats
path: root/package/broadcom-57xx
Commit message (Collapse)AuthorAgeFilesLines
* remove broadcom-57xx (only used on linux 2.4)Felix Fietkau2010-06-2628-25147/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21953 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] bump some revisions and update copyrightsAndy Boyett2009-09-101-3/+3
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@17554 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Added support for identifying the BCM53115 switch found in WRT610N.Felix Fietkau2009-08-281-2/+4
| | | | | | Signed-off-by: Tomas Kopal <Tomas.Kopal@altap.cz> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@17433 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm-2.4: nvram_set has been removed, remove some remaining calls to itFelix Fietkau2009-05-161-7/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15878 3c298f89-4303-0410-b956-a3cf2f4a3e73
* get rid of $Id$ - it has never helped us and it has broken too many patches ;)Felix Fietkau2009-04-1715-15/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15242 3c298f89-4303-0410-b956-a3cf2f4a3e73
* [package] replace some -I & -L flags with $(TARGET_CPPFLAGS) & ↵Nicolas Thill2009-02-241-3/+4
| | | | | | $(TARGET_LDFLAGS) when appropriate git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14651 3c298f89-4303-0410-b956-a3cf2f4a3e73
* remove some unused crapFelix Fietkau2008-06-1512-2361/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11472 3c298f89-4303-0410-b956-a3cf2f4a3e73
* (6/6) bcm57xx: packageFelix Fietkau2008-06-1540-0/+27527
This is the bcm57xx package. I have tested default vlan functions, but I dont have the equipment to test more advanced setups. The default vlan setup seems to be working fine. I also added the activate_gpio parameter which will make the driver activate the switch via gpio before probing for it. I'm not sure which method is best for autoload. For the wrt350n, I need the activate_gpio parameter. But its probably not a good idea to add that to the autoload file. On a system without a bcm57xx switch, isn't it a bad idea to mess with the gpios looking for the switch? Ideally, wouldn't it be best to load the bcm57xx module from broadcom-diag, after it has determined which router its on? I tried using 'request_module' from there, but had no success. For now, I am relying on preinit to load the bcm57xx module with activate_gpio param, after it has failed to load switch_robo and switch_adm. Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11471 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-25 17:09:33 +0000