1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage Denver Gingerich's USBSnoop Magnetic Card Reader Project
*
* \section SSec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this demo.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Human Interface Device (HID)</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>Keyboard</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF HID Standard, USBIF HID Usage Tables</td>
* </tr>
* <tr>
* <td><b>Usable Speeds:</b></td>
* <td>Low Speed Mode, Full Speed Mode</td>
* </tr>
* </table>
*
* \section SSec_Description Project Description:
*
* Firmware for a USB AVR powered USB TTL magnetic stripe reader (using a card
* reader such as the Omron V3B-4K) by Denver Gingerich. This project is designed
* to be used with the open source Stripe Snoop project at http://stripesnoop.sourceforge.net/.
*
* See http://ossguy.com/ss_usb/ for the USB reader hardware project website,
* including construction and support details.
*
* To use, connect your magnetic card reader device to the USB AVR as follows (pin and port mapping may be adjusted
* from the project makefile):
*
* <table>
* <tr>
* <td><b>Signal:</b></td>
* <td><b>AVR Port:</b></td>
* </tr>
* <tr>
* <td>Track 1 Data</td>
* <td>PORTC, Pin 1</td>
* </tr>
* <tr>
* <td>Track 1 Clock</td>
* <td>PORTC, Pin 2</td>
* </tr>
* <tr>
* <td>Track 2 Data</td>
* <td>PORTC, Pin 3</td>
* </tr>
* <tr>
* <td>Track 2 Clock</td>
* <td>PORTC, Pin 0</td>
* </tr>
* <tr>
* <td>Track 3 Data</td>
* <td>PORTC, Pin 5</td>
* </tr>
* <tr>
* <td>Track 3 Clock</td>
* <td>PORTC, Pin 6</td>
* </tr>
* <tr>
* <td>Card Detect</td>
* <td>PORTC, Pin 4</td>
* </tr>
* </table>
*
* This project is based on the LUFA Keyboard demonstration application,
* written by Denver Gingerich.
*
* This application uses a keyboard HID driver to communicate the data collected
* a TTL magnetic stripe reader to the connected computer. The raw bitstream
* obtained from the magnetic stripe reader is "typed" through the keyboard
* driver as 0's and 1's. After every card swipe, the demo will send a return key.
*
* \section SSec_Options Project Options
*
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td><b>Define Name:</b></td>
* <td><b>Location:</b></td>
* <td><b>Description:</b></td>
* </tr>
* <tr>
* <td>MAX_BITS</td>
* <td>CircularBitBuffer.h</td>
* <td>Gives the maximum number of bits per track which can be buffered by the device for later transmission to a host.</td>
* </tr>
* </table>
*/
|
