1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
|
/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.fourwalledcubicle.com
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Main source file for the TeensyHID bootloader. This file contains the complete bootloader logic.
*/
#include "TeensyHID.h"
/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
* via a soft reset. When cleared, the bootloader will abort, the USB interface will shut down and the application
* started via a forced watchdog reset.
*/
bool RunBootloader = true;
/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
* runs the bootloader processing routine until instructed to soft-exit.
*/
int main(void)
{
/* Setup hardware required for the bootloader */
SetupHardware();
/* Enable global interrupts so that the USB stack can function */
sei();
while (RunBootloader)
USB_USBTask();
/* Disconnect from the host - USB interface will be reset later along with the AVR */
USB_Detach();
/* Enable the watchdog and force a timeout to reset the AVR */
wdt_enable(WDTO_250MS);
for (;;);
}
/** Configures all hardware required for the bootloader. */
void SetupHardware(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
wdt_disable();
/* Relocate the interrupt vector table to the bootloader section */
MCUCR = (1 << IVCE);
MCUCR = (1 << IVSEL);
/* Initialize USB subsystem */
USB_Init();
}
/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready
* to relay data to and from the attached USB host.
*/
void EVENT_USB_Device_ConfigurationChanged(void)
{
/* Setup HID Report Endpoint */
Endpoint_ConfigureEndpoint(HID_EPNUM, EP_TYPE_INTERRUPT,
ENDPOINT_DIR_IN, HID_EPSIZE,
ENDPOINT_BANK_SINGLE);
}
/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific
* control requests that are not handled internally by the USB library (including the HID commands, which are
* all issued via the control endpoint), so that they can be handled appropriately for the application.
*/
void EVENT_USB_Device_UnhandledControlRequest(void)
{
/* Handle HID Class specific requests */
switch (USB_ControlRequest.bRequest)
{
case REQ_SetReport:
Endpoint_ClearSETUP();
/* Wait until the command has been sent by the host */
while (!(Endpoint_IsOUTReceived()));
/* Read in the write destination index */
uint16_t PageIndex = Endpoint_Read_Word_LE();
/* Check if the command is a program page command, or a start application command */
if (PageIndex == TEENSY_STARTAPPLICATION)
{
RunBootloader = false;
}
else
{
#if (FLASHEND > 0xFFFF)
uint32_t PageByteAddress = ((uint32_t)PageIndex << 8);
#else
uint16_t PageByteAddress = PageIndex;
#endif
/* Erase the given FLASH page, ready to be programmed */
boot_page_erase(PageByteAddress);
boot_spm_busy_wait();
/* Write each of the FLASH page's bytes in sequence */
#if (SPM_PAGESIZE == 128)
for (uint8_t PageByte = 0; PageByte < SPM_PAGESIZE; PageByte += 2)
#else
for (uint16_t PageByte = 0; PageByte < SPM_PAGESIZE; PageByte += 2)
#endif
{
/* Check if endpoint is empty - if so clear it and wait until ready for next packet */
if (!(Endpoint_BytesInEndpoint()))
{
Endpoint_ClearOUT();
while (!(Endpoint_IsOUTReceived()));
}
/* Write the next data word to the FLASH page */
boot_page_fill(PageByteAddress + PageByte, Endpoint_Read_Word_LE());
}
/* Write the filled FLASH page to memory */
boot_page_write(PageByteAddress);
boot_spm_busy_wait();
}
Endpoint_ClearOUT();
Endpoint_ClearStatusStage();
break;
}
}
|
