diff options
Diffstat (limited to 'Projects/AVRISP-MKII/AVRISP-MKII.txt')
-rw-r--r-- | Projects/AVRISP-MKII/AVRISP-MKII.txt | 21 |
1 files changed, 11 insertions, 10 deletions
diff --git a/Projects/AVRISP-MKII/AVRISP-MKII.txt b/Projects/AVRISP-MKII/AVRISP-MKII.txt index eb6431477..e36ffe231 100644 --- a/Projects/AVRISP-MKII/AVRISP-MKII.txt +++ b/Projects/AVRISP-MKII/AVRISP-MKII.txt @@ -3,7 +3,7 @@ * This file contains special DoxyGen information for the generation of the main page and other special * documentation pages. It is not a project source file. */ - + /** \mainpage AVRISP MKII Programmer Project * * \section SSec_Compat Project Compatibility: @@ -28,7 +28,7 @@ * <td><b>USB Class:</b></td> * <td>Vendor Specific Class</td> * </tr> - * <tr> + * <tr> * <td><b>USB Subclass:</b></td> * <td>N/A</td> * </tr> @@ -42,7 +42,7 @@ * </tr> * </table> * - * \section SSec_Description Project Description: + * \section SSec_Description Project Description: * * Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of * microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its @@ -240,31 +240,31 @@ * <td>VTARGET_ADC_CHANNEL</td> * <td>Makefile LUFA_OPTS</td> * <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined. - * <i>Ignored when compiled for targets lacking an ADC.</i></td> + * <i>Ignored when compiled for targets lacking an ADC.</i></td> * </tr> * <tr> * <td>ENABLE_ISP_PROTOCOL</td> * <td>Makefile LUFA_OPTS</td> - * <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td> + * <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>ENABLE_XPROG_PROTOCOL</td> * <td>Makefile LUFA_OPTS</td> - * <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td> + * <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>NO_VTARGET_DETECT</td> * <td>Makefile LUFA_OPTS</td> * <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer * to report a fixed 5V target voltage to the host regardless of the real target voltage. <i>Ignored when compiled for - * targets lacking an ADC.</i></td> + * targets lacking an ADC.</i></td> * </tr> * <tr> * <td>VTARGET_REF_VOLTS</td> * <td>Makefile LUFA_OPTS</td> * <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply * voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage - * to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> + * to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> * </tr> * <tr> * <td>VTARGET_SCALE_FACTOR</td> @@ -272,8 +272,8 @@ * <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the * ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be * measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set - * to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> - * </tr> + * to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> + * </tr> * <tr> * <td>LIBUSB_DRIVER_COMPAT</td> * <td>Makefile LUFA_OPTS</td> @@ -282,3 +282,4 @@ * </tr> * </table> */ + |