diff options
Diffstat (limited to 'keyboards')
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/bmc.c | 96 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/bmc.h | 101 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/config.h | 57 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/info.json | 24 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/keymaps/default/config.h | 19 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/keymaps/default/keymap.c | 74 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/keymaps/default/readme.md | 1 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/readme.md | 44 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/rules.mk | 90 | ||||
| -rw-r--r-- | keyboards/exclusive/e6v2/bmc/usbconfig.h | 393 |
10 files changed, 899 insertions, 0 deletions
diff --git a/keyboards/exclusive/e6v2/bmc/bmc.c b/keyboards/exclusive/e6v2/bmc/bmc.c new file mode 100644 index 000000000..257b68b8b --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/bmc.c @@ -0,0 +1,96 @@ +/* Copyright 2019 MechMerlin + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "bmc.h" +#include "rgblight.h" +#include "i2c_master.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + +#ifdef RGBLIGHT_ENABLE +extern rgblight_config_t rgblight_config; + +void rgblight_set(void) { + if (!rgblight_config.enable) { + for (uint8_t i = 0; i < RGBLED_NUM; i++) { + led[i].r = 0; + led[i].g = 0; + led[i].b = 0; + } + } + + i2c_init(); + i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100); +} +#endif + +__attribute__ ((weak)) +void matrix_scan_user(void) { +} + +void backlight_init_ports(void) { + // initialize pins D0, D1, D4 and D6 as output + setPinOutput(D0); + setPinOutput(D1); + setPinOutput(D4); + setPinOutput(D6); + + // turn RGB LEDs on + writePinHigh(D0); + writePinHigh(D1); + writePinHigh(D4); + writePinHigh(D6); +} + +void backlight_set(uint8_t level) { + if (level == 0) { + // turn RGB LEDs off + writePinLow(D0); + writePinLow(D1); + writePinLow(D4); + writePinLow(D6); + } else { + // turn RGB LEDs on + writePinHigh(D0); + writePinHigh(D1); + writePinHigh(D4); + writePinHigh(D6); + } +} diff --git a/keyboards/exclusive/e6v2/bmc/bmc.h b/keyboards/exclusive/e6v2/bmc/bmc.h new file mode 100644 index 000000000..06d23fbe6 --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/bmc.h @@ -0,0 +1,101 @@ +/* Copyright 2019 MechMerlin + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ + +// LAYOUT_all ignores the key often coded as ~# to the left of Enter on ISO layouts. +// This is done as it shares the same row AND col as the pipe key. +#define LAYOUT_all( \ + k50, k41, k42, k43, k44, k45, k61, k68, k78, k71, k49, k48, k47, k52, k4A, \ + k30, k31, k32, k33, k34, k35, k62, k67, k77, k72, k39, k38, k37, k36, \ + k20, k21, k22, k23, k24, k25, k63, k66, k76, k73, k29, k28, k26, \ + k10, k53, k11, k12, k13, k14, k15, k64, k6A, k7A, k74, k19, k18, k54, \ + k00, k01, k02, k75, k04, k08, k09, k05 \ +) \ +{ \ + { k00, k01, k02, KC_NO, k04, k05, KC_NO, KC_NO, k08, k09, KC_NO }, \ + { k10, k11, k12, k13, k14, k15, KC_NO, KC_NO, k18, k19, KC_NO }, \ + { k20, k21, k22, k23, k24, k25, k26, KC_NO, k28, k29, KC_NO }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, KC_NO }, \ + { KC_NO, k41, k42, k43, k44, k45, KC_NO, k47, k48, k49, k4A }, \ + { k50, KC_NO, k52, k53, k54, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \ + { KC_NO, k61, k62, k63, k64, KC_NO, k66, k67, k68, KC_NO, k6A }, \ + { KC_NO, k71, k72, k73, k74, k75, k76, k77, k78, KC_NO, k7A }, \ +} + +#define LAYOUT_60_ansi( \ + k50, k41, k42, k43, k44, k45, k61, k68, k78, k71, k49, k48, k47, k4A, \ + k30, k31, k32, k33, k34, k35, k62, k67, k77, k72, k39, k38, k37, k36, \ + k20, k21, k22, k23, k24, k25, k63, k66, k76, k73, k29, k28, k26, \ + k10, k11, k12, k13, k14, k15, k64, k6A, k7A, k74, k19, k18, \ + k00, k01, k02, k75, k04, k08, k09, k05 \ +) \ +{ \ + { k00, k01, k02, KC_NO, k04, k05, KC_NO, KC_NO, k08, k09, KC_NO }, \ + { k10, k11, k12, k13, k14, k15, KC_NO, KC_NO, k18, k19, KC_NO }, \ + { k20, k21, k22, k23, k24, k25, k26, KC_NO, k28, k29, KC_NO }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, KC_NO }, \ + { KC_NO, k41, k42, k43, k44, k45, KC_NO, k47, k48, k49, k4A }, \ + { k50, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \ + { KC_NO, k61, k62, k63, k64, KC_NO, k66, k67, k68, KC_NO, k6A }, \ + { KC_NO, k71, k72, k73, k74, k75, k76, k77, k78, KC_NO, k7A }, \ +} + +#define LAYOUT_60_hhkb( \ + k50, k41, k42, k43, k44, k45, k61, k68, k78, k71, k49, k48, k47, k52, k4A, \ + k30, k31, k32, k33, k34, k35, k62, k67, k77, k72, k39, k38, k37, k36, \ + k20, k21, k22, k23, k24, k25, k63, k66, k76, k73, k29, k28, k26, \ + k10, k11, k12, k13, k14, k15, k64, k6A, k7A, k74, k19, k18, k54, \ + k01, k02, k75, k08, k09 \ +) \ +{ \ + { KC_NO, k01, k02, KC_NO, KC_NO, k05, KC_NO, KC_NO, k08, k09, KC_NO }, \ + { k10, k11, k12, k13, k14, k15, KC_NO, KC_NO, k18, k19, KC_NO }, \ + { k20, k21, k22, k23, k24, k25, k26, KC_NO, k28, k29, KC_NO }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, KC_NO }, \ + { KC_NO, k41, k42, k43, k44, k45, KC_NO, k47, k48, k49, k4A }, \ + { k50, KC_NO, k52, KC_NO, k54, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \ + { KC_NO, k61, k62, k63, k64, KC_NO, k66, k67, k68, KC_NO, k6A }, \ + { KC_NO, k71, k72, k73, k74, k75, k76, k77, k78, KC_NO, k7A }, \ +} + +#define LAYOUT_60_tsangan( \ + k50, k41, k42, k43, k44, k45, k61, k68, k78, k71, k49, k48, k47, k52, k4A, \ + k30, k31, k32, k33, k34, k35, k62, k67, k77, k72, k39, k38, k37, k36, \ + k20, k21, k22, k23, k24, k25, k63, k66, k76, k73, k29, k28, k26, \ + k10, k11, k12, k13, k14, k15, k64, k6A, k7A, k74, k19, k18, k54, \ + k00, k01, k02, k75, k08, k09, k05 \ +) \ +{ \ + { k00, k01, k02, KC_NO, KC_NO, k05, KC_NO, KC_NO, k08, k09, KC_NO }, \ + { k10, k11, k12, k13, k14, k15, KC_NO, KC_NO, k18, k19, KC_NO }, \ + { k20, k21, k22, k23, k24, k25, k26, KC_NO, k28, k29, KC_NO }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, KC_NO }, \ + { KC_NO, k41, k42, k43, k44, k45, KC_NO, k47, k48, k49, k4A }, \ + { k50, KC_NO, k52, KC_NO, k54, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO }, \ + { KC_NO, k61, k62, k63, k64, KC_NO, k66, k67, k68, KC_NO, k6A }, \ + { KC_NO, k71, k72, k73, k74, k75, k76, k77, k78, KC_NO, k7A }, \ +} diff --git a/keyboards/exclusive/e6v2/bmc/config.h b/keyboards/exclusive/e6v2/bmc/config.h new file mode 100644 index 000000000..aae4d56dd --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/config.h @@ -0,0 +1,57 @@ +/* +Copyright 2019 MechMerlin + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER exclusive +#define PRODUCT e6v2 bmc +#define DESCRIPTION A custom 60% keyboard + +/* key matrix size */ +#define MATRIX_ROWS 8 +#define MATRIX_COLS 11 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ + +// 0 1 2 3 4 5 6 7 8 9 A +#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5, B6, B7 } +#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, C2, C3, C4, C5, D7 } +#define DIODE_DIRECTION COL2ROW + + +#define RGBLED_NUM 6 +#define RGBLIGHT_ANIMATIONS + +#define NO_UART 1 +#define BOOTLOADHID_BOOTLOADER 1 + +// Set bootmagic lite key to the key commonly programmed as Esc. +#define BOOTMAGIC_LITE_ROW 5 +#define BOOTMAGIC_LITE_COLUMN 0
\ No newline at end of file diff --git a/keyboards/exclusive/e6v2/bmc/info.json b/keyboards/exclusive/e6v2/bmc/info.json new file mode 100644 index 000000000..aa6d171ba --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/info.json @@ -0,0 +1,24 @@ +{ + "keyboard_name": "", + "url": "", + "maintainer": "qmk", + "width": 15, + "height": 5, + "layouts": { + "LAYOUT_all": { + "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.26}, {"x":10.0, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}] + }, + + "LAYOUT_60_ansi": { + "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0, "w":2}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":2.75}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}] + }, + + "LAYOUT_60_hhkb": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"|", "x":13, "y":0}, {"label":"~", "x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"Delete", "x":13.5, "y":1, "w":1.5}, {"label":"Control", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"Fn", "x":14, "y":3}, {"label":"Os", "x":1.5, "y":4}, {"label":"Alt", "x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"label":"Alt", "x":11, "y":4, "w":1.5}, {"label":"Os", "x":12.5, "y":4}] + }, + + "LAYOUT_60_tsangan": { + "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.5}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}, {"x":13.5, "y":4, "w":1.5}] + } + } +}
\ No newline at end of file diff --git a/keyboards/exclusive/e6v2/bmc/keymaps/default/config.h b/keyboards/exclusive/e6v2/bmc/keymaps/default/config.h new file mode 100644 index 000000000..26c6d6ade --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 MechMerlin + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/exclusive/e6v2/bmc/keymaps/default/keymap.c b/keyboards/exclusive/e6v2/bmc/keymaps/default/keymap.c new file mode 100644 index 000000000..730041917 --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/keymaps/default/keymap.c @@ -0,0 +1,74 @@ +/* Copyright 2019 MechMerlin + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// Defines the keycodes used by our macros in process_record_user +enum custom_keycodes { + QMKBEST = SAFE_RANGE, + QMKURL +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[0] = LAYOUT_60_ansi( + KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_RCTL, MO(1) + ), + +[1] = LAYOUT_60_ansi( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + BL_TOGG, BL_INC, BL_DEC, BL_STEP, RESET, EEP_RST, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + RGB_TOG, RGB_MOD, RGB_HUI, RGB_SAI, RGB_VAI, RGB_SPI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, RGB_RMOD, RGB_HUD, RGB_SAD, RGB_VAD, RGB_SPD, KC_TRNS, KC_MUTE, KC_VOLD, KC_VOLU, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QMKBEST: + if (record->event.pressed) { + // when keycode QMKBEST is pressed + SEND_STRING("QMK is the best thing ever!"); + } else { + // when keycode QMKBEST is released + } + break; + case QMKURL: + if (record->event.pressed) { + // when keycode QMKURL is pressed + SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER)); + } else { + // when keycode QMKURL is released + } + break; + } + return true; +} + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/exclusive/e6v2/bmc/keymaps/default/readme.md b/keyboards/exclusive/e6v2/bmc/keymaps/default/readme.md new file mode 100644 index 000000000..4a1b6efa6 --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for bmc diff --git a/keyboards/exclusive/e6v2/bmc/readme.md b/keyboards/exclusive/e6v2/bmc/readme.md new file mode 100644 index 000000000..3e2d19748 --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/readme.md @@ -0,0 +1,44 @@ +# E6-V2 Bootmapper Client (ps2avrgb) + +These docs are for the BMC version of the E6-V2 PCB which has an atmega32a microcontroller. Please do not flash this `.hex` file on your atmega32u4 equipped E6-V2. + +Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin) +Hardware Supported: ps2avrgb E6-V2 with atmega32a microcontroller +Hardware Availability: [geekhack.org/index.php?topic=90787.0](https://geekhack.org/index.php?topic=90787.0) + +Make example for this keyboard (after setting up your build environment): + + make exclusive/e6v2/bmc:default + +Flashing + +ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. + +**Reset Key:** Hold down the key located at `K00`, commonly programmed as left control while plugging in the keyboard. You may also hold down the key located at `K50`, commonly programmed as the escape key. + +Windows: +1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash). +2. Place your keyboard into reset. +3. Press the `Find Device` button and ensure that your keyboard is found. +4. Press the `Open .hex File` button and locate the `.hex` file you created. +5. Press the `Flash Device` button and wait for the process to complete. + +macOS: +1. Install homebrew by typing the following: + ``` + /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)" + ``` +2. Install `crosspack-avr`. + ``` + brew cask install crosspack-avr + ``` +3. Install the following packages: + ``` + brew install python + pip3 install pyusb + brew install --HEAD`https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb + +4. Place your keyboard into reset. +5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/exclusive/e6v2/bmc/rules.mk b/keyboards/exclusive/e6v2/bmc/rules.mk new file mode 100644 index 000000000..59f98e6f4 --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/rules.mk @@ -0,0 +1,90 @@ +# MCU name +#MCU = at90usb1286 +MCU = atmega32a +PROTOCOL = VUSB + +NO_UART = yes +NO_SUSPEND_POWER_DOWN = yes + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 12000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +# ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +# F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS = -DDEBUG_LEVEL=0 + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = bootloadHID + + +# If you don't know the bootloader type, then you can specify the +# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +# OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +RGBLIGHT_CUSTOM_DRIVER = yes +RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) + +SRC += i2c_master.c + +PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex diff --git a/keyboards/exclusive/e6v2/bmc/usbconfig.h b/keyboards/exclusive/e6v2/bmc/usbconfig.h new file mode 100644 index 000000000..c52c90ce8 --- /dev/null +++ b/keyboards/exclusive/e6v2/bmc/usbconfig.h @@ -0,0 +1,393 @@ +/* Name: usbconfig.h + * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers + * Author: Christian Starkjohann + * Creation Date: 2005-04-01 + * Tabsize: 4 + * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH + * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) + * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $ + */ + +#pragma once + +#include "config.h" + +/* +General Description: +This file is an example configuration (with inline documentation) for the USB +driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is +also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may +wire the lines to any other port, as long as D+ is also wired to INT0 (or any +other hardware interrupt, as long as it is the highest level interrupt, see +section at the end of this file). +*/ + +/* ---------------------------- Hardware Config ---------------------------- */ + +#define USB_CFG_IOPORTNAME D +/* This is the port where the USB bus is connected. When you configure it to + * "B", the registers PORTB, PINB and DDRB will be used. + */ +#define USB_CFG_DMINUS_BIT 3 +/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. + * This may be any bit in the port. + */ +#define USB_CFG_DPLUS_BIT 2 +/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. + * This may be any bit in the port. Please note that D+ must also be connected + * to interrupt pin INT0! [You can also use other interrupts, see section + * "Optional MCU Description" below, or you can connect D- to the interrupt, as + * it is required if you use the USB_COUNT_SOF feature. If you use D- for the + * interrupt, the USB interrupt will also be triggered at Start-Of-Frame + * markers every millisecond.] + */ +#define USB_CFG_CLOCK_KHZ (F_CPU/1000) +/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, + * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code + * require no crystal, they tolerate +/- 1% deviation from the nominal + * frequency. All other rates require a precision of 2000 ppm and thus a + * crystal! + * Since F_CPU should be defined to your actual clock rate anyway, you should + * not need to modify this setting. + */ +#define USB_CFG_CHECK_CRC 0 +/* Define this to 1 if you want that the driver checks integrity of incoming + * data packets (CRC checks). CRC checks cost quite a bit of code size and are + * currently only available for 18 MHz crystal clock. You must choose + * USB_CFG_CLOCK_KHZ = 18000 if you enable this option. + */ + +/* ----------------------- Optional Hardware Config ------------------------ */ + +/* #define USB_CFG_PULLUP_IOPORTNAME D */ +/* If you connect the 1.5k pullup resistor from D- to a port pin instead of + * V+, you can connect and disconnect the device from firmware by calling + * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). + * This constant defines the port on which the pullup resistor is connected. + */ +/* #define USB_CFG_PULLUP_BIT 4 */ +/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined + * above) where the 1.5k pullup resistor is connected. See description + * above for details. + */ + +/* --------------------------- Functional Range ---------------------------- */ + +#define USB_CFG_HAVE_INTRIN_ENDPOINT 1 +/* Define this to 1 if you want to compile a version with two endpoints: The + * default control endpoint 0 and an interrupt-in endpoint (any other endpoint + * number). + */ +#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1 +/* Define this to 1 if you want to compile a version with three endpoints: The + * default control endpoint 0, an interrupt-in endpoint 3 (or the number + * configured below) and a catch-all default interrupt-in endpoint as above. + * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. + */ +#define USB_CFG_EP3_NUMBER 3 +/* If the so-called endpoint 3 is used, it can now be configured to any other + * endpoint number (except 0) with this macro. Default if undefined is 3. + */ +/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */ +/* The above macro defines the startup condition for data toggling on the + * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. + * Since the token is toggled BEFORE sending any data, the first packet is + * sent with the oposite value of this configuration! + */ +#define USB_CFG_IMPLEMENT_HALT 0 +/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature + * for endpoint 1 (interrupt endpoint). Although you may not need this feature, + * it is required by the standard. We have made it a config option because it + * bloats the code considerably. + */ +#define USB_CFG_SUPPRESS_INTR_CODE 0 +/* Define this to 1 if you want to declare interrupt-in endpoints, but don't + * want to send any data over them. If this macro is defined to 1, functions + * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if + * you need the interrupt-in endpoints in order to comply to an interface + * (e.g. HID), but never want to send any data. This option saves a couple + * of bytes in flash memory and the transmit buffers in RAM. + */ +#define USB_CFG_INTR_POLL_INTERVAL 1 +/* If you compile a version with endpoint 1 (interrupt-in), this is the poll + * interval. The value is in milliseconds and must not be less than 10 ms for + * low speed devices. + */ +#define USB_CFG_IS_SELF_POWERED 0 +/* Define this to 1 if the device has its own power supply. Set it to 0 if the + * device is powered from the USB bus. + */ +#define USB_CFG_MAX_BUS_POWER 500 +/* Set this variable to the maximum USB bus power consumption of your device. + * The value is in milliamperes. [It will be divided by two since USB + * communicates power requirements in units of 2 mA.] + */ +#define USB_CFG_IMPLEMENT_FN_WRITE 1 +/* Set this to 1 if you want usbFunctionWrite() to be called for control-out + * transfers. Set it to 0 if you don't need it and want to save a couple of + * bytes. + */ +#define USB_CFG_IMPLEMENT_FN_READ 0 +/* Set this to 1 if you need to send control replies which are generated + * "on the fly" when usbFunctionRead() is called. If you only want to send + * data from a static buffer, set it to 0 and return the data from + * usbFunctionSetup(). This saves a couple of bytes. + */ +#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 +/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. + * You must implement the function usbFunctionWriteOut() which receives all + * interrupt/bulk data sent to any endpoint other than 0. The endpoint number + * can be found in 'usbRxToken'. + */ +#define USB_CFG_HAVE_FLOWCONTROL 0 +/* Define this to 1 if you want flowcontrol over USB data. See the definition + * of the macros usbDisableAllRequests() and usbEnableAllRequests() in + * usbdrv.h. + */ +#define USB_CFG_DRIVER_FLASH_PAGE 0 +/* If the device has more than 64 kBytes of flash, define this to the 64 k page + * where the driver's constants (descriptors) are located. Or in other words: + * Define this to 1 for boot loaders on the ATMega128. + */ +#define USB_CFG_LONG_TRANSFERS 0 +/* Define this to 1 if you want to send/receive blocks of more than 254 bytes + * in a single control-in or control-out transfer. Note that the capability + * for long transfers increases the driver size. + */ +/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */ +/* This macro is a hook if you want to do unconventional things. If it is + * defined, it's inserted at the beginning of received message processing. + * If you eat the received message and don't want default processing to + * proceed, do a return after doing your things. One possible application + * (besides debugging) is to flash a status LED on each packet. + */ +/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */ +/* This macro is a hook if you need to know when an USB RESET occurs. It has + * one parameter which distinguishes between the start of RESET state and its + * end. + */ +/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */ +/* This macro (if defined) is executed when a USB SET_ADDRESS request was + * received. + */ +#define USB_COUNT_SOF 1 +/* define this macro to 1 if you need the global variable "usbSofCount" which + * counts SOF packets. This feature requires that the hardware interrupt is + * connected to D- instead of D+. + */ +/* #ifdef __ASSEMBLER__ + * macro myAssemblerMacro + * in YL, TCNT0 + * sts timer0Snapshot, YL + * endm + * #endif + * #define USB_SOF_HOOK myAssemblerMacro + * This macro (if defined) is executed in the assembler module when a + * Start Of Frame condition is detected. It is recommended to define it to + * the name of an assembler macro which is defined here as well so that more + * than one assembler instruction can be used. The macro may use the register + * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages + * immediately after an SOF pulse may be lost and must be retried by the host. + * What can you do with this hook? Since the SOF signal occurs exactly every + * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in + * designs running on the internal RC oscillator. + * Please note that Start Of Frame detection works only if D- is wired to the + * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! + */ +#define USB_CFG_CHECK_DATA_TOGGLING 0 +/* define this macro to 1 if you want to filter out duplicate data packets + * sent by the host. Duplicates occur only as a consequence of communication + * errors, when the host does not receive an ACK. Please note that you need to + * implement the filtering yourself in usbFunctionWriteOut() and + * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable + * for each control- and out-endpoint to check for duplicate packets. + */ +#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 +/* define this macro to 1 if you want the function usbMeasureFrameLength() + * compiled in. This function can be used to calibrate the AVR's RC oscillator. + */ +#define USB_USE_FAST_CRC 0 +/* The assembler module has two implementations for the CRC algorithm. One is + * faster, the other is smaller. This CRC routine is only used for transmitted + * messages where timing is not critical. The faster routine needs 31 cycles + * per byte while the smaller one needs 61 to 69 cycles. The faster routine + * may be worth the 32 bytes bigger code size if you transmit lots of data and + * run the AVR close to its limit. + */ + +/* -------------------------- Device Description --------------------------- */ + +#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF) +/* USB vendor ID for the device, low byte first. If you have registered your + * own Vendor ID, define it here. Otherwise you may use one of obdev's free + * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF) +/* This is the ID of the product, low byte first. It is interpreted in the + * scope of the vendor ID. If you have registered your own VID with usb.org + * or if you have licensed a PID from somebody else, define it here. Otherwise + * you may use one of obdev's free shared VID/PID pairs. See the file + * USB-IDs-for-free.txt for details! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_VERSION 0x00, 0x02 +/* Version number of the device: Minor number first, then major number. + */ +#define USB_CFG_VENDOR_NAME 'G', 'r', 'a', 'y', ' ', 'S', 't', 'u', 'd', 'i', 'o' +#define USB_CFG_VENDOR_NAME_LEN 11 +/* These two values define the vendor name returned by the USB device. The name + * must be given as a list of characters under single quotes. The characters + * are interpreted as Unicode (UTF-16) entities. + * If you don't want a vendor name string, undefine these macros. + * ALWAYS define a vendor name containing your Internet domain name if you use + * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for + * details. + */ +#define USB_CFG_DEVICE_NAME 'H', 'B', '8', '5' +#define USB_CFG_DEVICE_NAME_LEN 4 +/* Same as above for the device name. If you don't want a device name, undefine + * the macros. See the file USB-IDs-for-free.txt before you assign a name if + * you use a shared VID/PID. + */ +/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */ +/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */ +/* Same as above for the serial number. If you don't want a serial number, + * undefine the macros. + * It may be useful to provide the serial number through other means than at + * compile time. See the section about descriptor properties below for how + * to fine tune control over USB descriptors such as the string descriptor + * for the serial number. + */ +#define USB_CFG_DEVICE_CLASS 0 +#define USB_CFG_DEVICE_SUBCLASS 0 +/* See USB specification if you want to conform to an existing device class. + * Class 0xff is "vendor specific". + */ +#define USB_CFG_INTERFACE_CLASS 3 /* HID */ +#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */ +#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */ +/* See USB specification if you want to conform to an existing device class or + * protocol. The following classes must be set at interface level: + * HID class is 3, no subclass and protocol required (but may be useful!) + * CDC class is 2, use subclass 2 and protocol 1 for ACM + */ +#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 +/* Define this to the length of the HID report descriptor, if you implement + * an HID device. Otherwise don't define it or define it to 0. + * If you use this define, you must add a PROGMEM character array named + * "usbHidReportDescriptor" to your code which contains the report descriptor. + * Don't forget to keep the array and this define in sync! + */ + +/* #define USB_PUBLIC static */ +/* Use the define above if you #include usbdrv.c instead of linking against it. + * This technique saves a couple of bytes in flash memory. + */ + +/* ------------------- Fine Control over USB Descriptors ------------------- */ +/* If you don't want to use the driver's default USB descriptors, you can + * provide our own. These can be provided as (1) fixed length static data in + * flash memory, (2) fixed length static data in RAM or (3) dynamically at + * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more + * information about this function. + * Descriptor handling is configured through the descriptor's properties. If + * no properties are defined or if they are 0, the default descriptor is used. + * Possible properties are: + * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched + * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is + * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if + * you want RAM pointers. + * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found + * in static memory is in RAM, not in flash memory. + * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), + * the driver must know the descriptor's length. The descriptor itself is + * found at the address of a well known identifier (see below). + * List of static descriptor names (must be declared PROGMEM if in flash): + * char usbDescriptorDevice[]; + * char usbDescriptorConfiguration[]; + * char usbDescriptorHidReport[]; + * char usbDescriptorString0[]; + * int usbDescriptorStringVendor[]; + * int usbDescriptorStringDevice[]; + * int usbDescriptorStringSerialNumber[]; + * Other descriptors can't be provided statically, they must be provided + * dynamically at runtime. + * + * Descriptor properties are or-ed or added together, e.g.: + * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) + * + * The following descriptors are defined: + * USB_CFG_DESCR_PROPS_DEVICE + * USB_CFG_DESCR_PROPS_CONFIGURATION + * USB_CFG_DESCR_PROPS_STRINGS + * USB_CFG_DESCR_PROPS_STRING_0 + * USB_CFG_DESCR_PROPS_STRING_VENDOR + * USB_CFG_DESCR_PROPS_STRING_PRODUCT + * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER + * USB_CFG_DESCR_PROPS_HID + * USB_CFG_DESCR_PROPS_HID_REPORT + * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver) + * + * Note about string descriptors: String descriptors are not just strings, they + * are Unicode strings prefixed with a 2 byte header. Example: + * int serialNumberDescriptor[] = { + * USB_STRING_DESCRIPTOR_HEADER(6), + * 'S', 'e', 'r', 'i', 'a', 'l' + * }; + */ + +#define USB_CFG_DESCR_PROPS_DEVICE 0 +#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 +#define USB_CFG_DESCR_PROPS_STRINGS 0 +#define USB_CFG_DESCR_PROPS_STRING_0 0 +#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 +#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 +#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 +#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID 0 +#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID_REPORT 0 +#define USB_CFG_DESCR_PROPS_UNKNOWN 0 + +#define usbMsgPtr_t unsigned short +/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to + * a scalar type here because gcc generates slightly shorter code for scalar + * arithmetics than for pointer arithmetics. Remove this define for backward + * type compatibility or define it to an 8 bit type if you use data in RAM only + * and all RAM is below 256 bytes (tiny memory model in IAR CC). + */ + +/* ----------------------- Optional MCU Description ------------------------ */ + +/* The following configurations have working defaults in usbdrv.h. You + * usually don't need to set them explicitly. Only if you want to run + * the driver on a device which is not yet supported or with a compiler + * which is not fully supported (such as IAR C) or if you use a differnt + * interrupt than INT0, you may have to define some of these. + */ +/* #define USB_INTR_CFG MCUCR */ +/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */ +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE GIMSK */ +/* #define USB_INTR_ENABLE_BIT INT0 */ +/* #define USB_INTR_PENDING GIFR */ +/* #define USB_INTR_PENDING_BIT INTF0 */ +/* #define USB_INTR_VECTOR INT0_vect */ + +/* Set INT1 for D- falling edge to count SOF */ +/* #define USB_INTR_CFG EICRA */ +#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10)) +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE EIMSK */ +#define USB_INTR_ENABLE_BIT INT1 +/* #define USB_INTR_PENDING EIFR */ +#define USB_INTR_PENDING_BIT INTF1 +#define USB_INTR_VECTOR INT1_vect |