[Keyboard] Iris via support, Rev 3 updates (#4849)

* Add encoder support

* Add VIA support to Iris Rev. 3

* Update pinout and disable mouse keys to free up space

* Rollout VIA support to all Iris revisions

* Update default keymap

* Update vendor ID

1 files changed, 8 insertions, 32 deletions

diff --git a/keyboards/iris/rules.mk b/keyboards/iris/rules.mk
index e93d7dae8..69bc62f87 100644
--- a/keyboards/iris/rules.mk
+++ b/keyboards/iris/rules.mk
@@ -1,36 +1,6 @@
-# MCU name
 MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
 # Bootloader
@@ -50,8 +20,9 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically
 #
+
 BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
 CONSOLE_ENABLE = no         # Console for debug(+400)
 COMMAND_ENABLE = yes        # Commands for debug and configuration
@@ -61,10 +32,15 @@ MIDI_ENABLE = no            # MIDI controls
 AUDIO_ENABLE = no           # Audio output on port C6
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight. 
+RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 
 SPLIT_KEYBOARD = yes
 
 DEFAULT_FOLDER = iris/rev2
+
+# VIA Support - Comment these 3 lines out to disable
+RAW_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes
+SRC += keyboards/wilba_tech/wt_main.c