path: root/os/hal/platforms/STM8S/serial_lld.c

/*
    ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
                 2011,2012 Giovanni Di Sirio.

    This file is part of ChibiOS/RT.

    ChibiOS/RT is free software; you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation; either version 3 of the License, or
    (at your option) any later version.

    ChibiOS/RT is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

/**
 * @file    STM8S/serial_lld.c
 * @brief   STM8S low level serial driver code.
 *
 * @addtogroup SERIAL
 * @{
 */

#include "ch.h"
#include "hal.h"

#if HAL_USE_SERIAL || defined(__DOXYGEN__)

/*===========================================================================*/
/* Driver exported variables.                                                */
/*===========================================================================*/

/**
 * @brief   UART1 serial driver identifier.
 */
#if STM8S_SERIAL_USE_UART1 || defined(__DOXYGEN__)
SerialDriver SD1;
#endif

/**
 * @brief   UART2 serial driver identifier.
 */
#if STM8S_SERIAL_USE_UART2 || defined(__DOXYGEN__)
SerialDriver SD2;
#endif

/**
 * @brief   UART3 serial driver identifier.
 */
#if STM8S_SERIAL_USE_UART3 || defined(__DOXYGEN__)
SerialDriver SD3;
#endif

/*===========================================================================*/
/* Driver local variables.                                                   */
/*===========================================================================*/

/**
 * @brief   Driver default configuration.
 */
static ROMCONST SerialConfig default_config = {
  BRR(SERIAL_DEFAULT_BITRATE),
  SD_MODE_PARITY_NONE | SD_MODE_STOP_1
};

/*===========================================================================*/
/* Driver local functions.                                                   */
/*===========================================================================*/

static void set_error(SerialDriver *sdp, uint8_t sr) {
  flagsmask_t sts = 0;

  /* Note, SR register bit definitions are equal for all UARTs so using
     the UART1 definitions is fine.*/
  if (sr & UART1_SR_OR)
    sts |= SD_OVERRUN_ERROR;
  if (sr & UART1_SR_NF)
    sts |= SD_NOISE_ERROR;
  if (sr & UART1_SR_FE)
    sts |= SD_FRAMING_ERROR;
  if (sr & UART1_SR_PE)
    sts |= SD_PARITY_ERROR;
  chSysLockFromIsr();
  chnAddFlagsI(sdp, sts);
  chSysUnlockFromIsr();
}

#if STM8S_SERIAL_USE_UART1 || defined(__DOXYGEN__)
static void notify1(GenericQueue *qp) {

  (void)qp;
  UART1->CR2 |= UART1_CR2_TIEN;
}

/**
 * @brief   UART1 initialization.
 *
 * @param[in] config    architecture-dependent serial driver configuration
 */
static void uart1_init(const SerialConfig *config) {

  UART1->BRR2 = (uint8_t)(((uint8_t)(config->sc_brr >> 8) & (uint8_t)0xF0) |
                          ((uint8_t)config->sc_brr & (uint8_t)0x0F));
  UART1->BRR1 = (uint8_t)(config->sc_brr >> 4);
  UART1->CR1  = (uint8_t)(config->sc_mode &
                          SD_MODE_PARITY);  /* PIEN included.               */
  UART1->CR2  = UART1_CR2_RIEN | UART1_CR2_TEN | UART1_CR2_REN;
  UART1->CR3  = (uint8_t)(config->sc_mode & SD_MODE_STOP);
  UART1->CR4  = 0;
  UART1->CR5  = 0;
  UART1->PSCR = 1;
  (void)UART1->SR;
  (void)UART1->DR;
}

/**
 * @brief   UART1 de-initialization.
 */
static void uart1_deinit(void) {

  UART1->CR1  = UART1_CR1_UARTD;
  UART1->CR2  = 0;
  UART1->CR3  = 0;
  UART1->CR4  = 0;
  UART1->CR5  = 0;
  UART1->PSCR = 0;
}
#endif /* STM8S_SERIAL_USE_UART1 */

#if STM8S_SERIAL_USE_UART2 || defined(__DOXYGEN__)
static void notify2(GenericQueue *qp) {

  (void)qp;
  UART2->CR2 |= UART2_CR2_TIEN;
}

/**
 * @brief   UART2 initialization.
 *
 * @param[in] config    architecture-dependent serial driver configuration
 */
static void uart2_init(const SerialConfig *config) {

  UART2->BRR2 = (uint8_t)(((uint8_t)(config->sc_brr >> 8) & (uint8_t)0xF0) |
                          ((uint8_t)config->sc_brr & (uint8_t)0x0F));
  UART2->BRR1 = (uint8_t)(config->sc_brr >> 4);
  UART2->CR1  = (uint8_t)(config->sc_mode &
                          SD_MODE_PARITY);  /* PIEN included.               */
  UART2->CR2  = UART2_CR2_RIEN | UART2_CR2_TEN | UART2_CR2_REN;
  UART2->CR3  = (uint8_t)(config->sc_mode & SD_MODE_STOP);
  UART2->CR4  = 0;
  UART2->CR5  = 0;
  UART2->CR6  = 0;
  UART2->PSCR = 1;
  (void)UART2->SR;
  (void)UART2->DR;
}

/**
 * @brief   UART1 de-initialization.
 */
static void uart2_deinit(void) {

  UART2->CR1  = UART2_CR1_UARTD;
  UART2->CR2  = 0;
  UART2->CR3  = 0;
  UART2->CR4  = 0;
  UART2->CR5  = 0;
  UART2->CR6  = 0;
  UART2->PSCR = 0;
}
#endif /* STM8S_SERIAL_USE_UART1 */

#if STM8S_SERIAL_USE_UART3 || defined(__DOXYGEN__)
static void notify3(GenericQueue *qp) {

  (void)qp;
  UART3->CR2 |= UART3_CR2_TIEN;
}

/**
 * @brief   UART3 initialization.
 *
 * @param[in] config    architecture-dependent serial driver configuration
 */
static void uart3_init(const SerialConfig *config) {

  UART3->BRR2 = (uint8_t)(((uint8_t)(config->sc_brr >> 8) & (uint8_t)0xF0) |
                          ((uint8_t)config->sc_brr & (uint8_t)0x0F));
  UART3->BRR1 = (uint8_t)(config->sc_brr >> 4);
  UART3->CR1  = (uint8_t)(config->sc_mode &
                          SD_MODE_PARITY);  /* PIEN included.               */
  UART3->CR2  = UART3_CR2_RIEN | UART3_CR2_TEN | UART3_CR2_REN;
  UART3->CR3  = (uint8_t)(config->sc_mode & SD_MODE_STOP);
  UART3->CR4  = 0;
  UART3->CR6  = 0;
  (void)UART3->SR;
  (void)UART3->DR;
}

/**
 * @brief   UART3 de-initialization.
 */
static void uart3_deinit(void) {

  UART3->CR1  = UART3_CR1_UARTD;
  UART3->CR2  = 0;
  UART3->CR3  = 0;
  UART3->CR4  = 0;
  UART3->CR6  = 0;
}
#endif /* STM8S_SERIAL_USE_UART3 */

/*===========================================================================*/
/* Driver interrupt handlers.                                                */
/*===========================================================================*/

#if STM8S_SERIAL_USE_UART1 || defined(__DOXYGEN__)
/**
 * @brief   IRQ 17 service routine.
 *
 * @isr
 */
CH_IRQ_HANDLER(17) {
  msg_t b;

  CH_IRQ_PROLOGUE();

  chSysLockFromIsr();
  b = sdRequestDataI(&SD1);
  chSysUnlockFromIsr();
  if (b < Q_OK)
    UART1->CR2 &= (uint8_t)~UART1_CR2_TIEN;
  else
    UART1->DR = (uint8_t)b;

  CH_IRQ_EPILOGUE();
}

/**
 * @brief   IRQ 18 service routine.
 *
 * @isr
 */
CH_IRQ_HANDLER(18) {
  uint8_t sr = UART1->SR;

  CH_IRQ_PROLOGUE();

  if ((sr = UART1->SR) & (UART1_SR_OR | UART1_SR_NF |
                          UART1_SR_FE | UART1_SR_PE))
    set_error(&SD1, sr);
  chSysLockFromIsr();
  sdIncomingDataI(&SD1, UART1->DR);
  chSysUnlockFromIsr();

  CH_IRQ_EPILOGUE();
}
#endif /* STM8S_SERIAL_USE_UART1 */

#if STM8S_SERIAL_USE_UART2 || defined(__DOXYGEN__)
/**
 * @brief   IRQ 20 service routine.
 *
 * @isr
 */
CH_IRQ_HANDLER(20) {
  msg_t b;

  CH_IRQ_PROLOGUE();

  chSysLockFromIsr();
  b = sdRequestDataI(&SD2);
  chSysUnlockFromIsr();
  if (b < Q_OK)
    UART2->CR2 &= (uint8_t)~UART2_CR2_TIEN;
  else
    UART2->DR = (uint8_t)b;

  CH_IRQ_EPILOGUE();
}

/**
 * @brief   IRQ 21 service routine.
 *
 * @isr
 */
CH_IRQ_HANDLER(21) {
  uint8_t sr = UART2->SR;

  CH_IRQ_PROLOGUE();

  if ((sr = UART2->SR) & (UART2_SR_OR | UART2_SR_NF |
                          UART2_SR_FE | UART2_SR_PE))
    set_error(&SD2, sr);
  chSysLockFromIsr();
  sdIncomingDataI(&SD2, UART2->DR);
  chSysUnlockFromIsr();

  CH_IRQ_EPILOGUE();
}
#endif /* STM8S_SERIAL_USE_UART2 */

#if STM8S_SERIAL_USE_UART3 || defined(__DOXYGEN__)
/**
 * @brief   IRQ 20 service routine.
 *
 * @isr
 */
CH_IRQ_HANDLER(20) {
  msg_t b;

  CH_IRQ_PROLOGUE();

  chSysLockFromIsr();
  b = sdRequestDataI(&SD3);
  chSysUnlockFromIsr();
  if (b < Q_OK)
    UART3->CR2 &= (uint8_t)~UART3_CR2_TIEN;
  else
    UART3->DR = (uint8_t)b;

  CH_IRQ_EPILOGUE();
}

/**
 * @brief   IRQ 21 service routine.
 *
 * @isr
 */
CH_IRQ_HANDLER(21) {
  uint8_t sr = UART3->SR;

  CH_IRQ_PROLOGUE();

  if ((sr = UART3->SR) & (UART3_SR_OR | UART3_SR_NF |
                          UART3_SR_FE | UART3_SR_PE))
    set_error(&SD3, sr);
  chSysLockFromIsr();
  sdIncomingDataI(&SD3, UART3->DR);
  chSysUnlockFromIsr();

  CH_IRQ_EPILOGUE();
}
#endif /* STM8S_SERIAL_USE_UART3 */

/*===========================================================================*/
/* Driver exported functions.                                                */
/*===========================================================================*/

/**
 * @brief   Low level serial driver initialization.
 *
 * @notapi
 */
void sd_lld_init(void) {

#if STM8S_SERIAL_USE_UART1
  sdObjectInit(&SD1, NULL, notify1);
  CLK->PCKENR1 |= CLK_PCKENR1_UART1;        /* PCKEN12, clock source.       */
  UART1->CR1 = UART1_CR1_UARTD;             /* UARTD (low power).           */
#endif

#if STM8S_SERIAL_USE_UART2
  sdObjectInit(&SD2, NULL, notify2);
  CLK->PCKENR1 |= CLK_PCKENR1_UART2;        /* PCKEN13, clock source.       */
  UART2->CR1 = UART2_CR1_UARTD;             /* UARTD (low power).           */
#endif

#if STM8S_SERIAL_USE_UART3
  sdObjectInit(&SD3, NULL, notify3);
  CLK->PCKENR1 |= CLK_PCKENR1_UART3;        /* PCKEN13, clock source.       */
  UART3->CR1 = UART3_CR1_UARTD;             /* UARTD (low power).           */
#endif
}

/**
 * @brief   Low level serial driver configuration and (re)start.
 *
 * @param[in] sdp       pointer to a @p SerialDriver object
 * @param[in] config    the architecture-dependent serial driver configuration.
 *                      If this parameter is set to @p NULL then a default
 *                      configuration is used.
 *
 * @notapi
 */
void sd_lld_start(SerialDriver *sdp, const SerialConfig *config) {

  if (config == NULL)
    config = &default_config;

#if STM8S_SERIAL_USE_UART1
  if (&SD1 == sdp) {
    uart1_init(config);
    return;
  }
#endif
#if STM8S_SERIAL_USE_UART2
  if (&SD2 == sdp) {
    uart2_init(config);
    return;
  }
#endif
#if STM8S_SERIAL_USE_UART3
  if (&SD3 == sdp) {
    uart3_init(config);
    return;
  }
#endif
}

/**
 * @brief   Low level serial driver stop.
 * @details De-initializes the USART, stops the associated clock, resets the
 *          interrupt vector.
 *
 * @param[in] sdp       pointer to a @p SerialDriver object
 *
 * @notapi
 */
void sd_lld_stop(SerialDriver *sdp) {

#if STM8S_SERIAL_USE_UART1
  if (&SD1 == sdp) {
    uart1_deinit();
    return;
  }
#endif
#if STM8S_SERIAL_USE_UART2
  if (&SD2 == sdp) {
    uart2_deinit();
    return;
  }
#endif
#if STM8S_SERIAL_USE_UART3
  if (&SD3 == sdp) {
    uart3_deinit();
    return;
  }
#endif
}

#endif /* HAL_USE_SERIAL */

/** @} */