blob: 8cd215948719628d8d55d085b2c9decd374208ad (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
|
/*
ChibiOS/RT - Copyright (C) 2006-2014 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for STMicroelectronics STM3220G-EVAL board.
*/
/*
* Board identifier.
*/
#define BOARD_ST_STM3220G_EVAL
#define BOARD_NAME "ST STM3220G-EVAL"
/*
* Board frequencies.
* NOTE: The HSE crystal is not fitted by default on the board.
*/
#define STM32_LSECLK 32768
#define STM32_HSECLK 25000000
/*
* MCU type as defined in the ST header file stm32f2xx.h.
*/
#define STM32F2XX
/*
* IO pins assignments.
*/
#define GPIOA_WAKEUP_BUTTON 0
#define GPIOB_ETHER_INT 14
#define GPIOB_NAND_INT 15
#define GPIOC_TAMPER_BUTTON 0
#define GPIOC_LED4 7
#define GPIOF_POT 9
#define GPIOG_LED1 6
#define GPIOG_LED2 8
#define GPIOG_USER_BUTTON 15
#define GPIOH_EXPANDER_INT 12
#define GPIOH_SD_DETECT 13
#define GPIOI_LED3 9
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
* Please refer to the STM32 Reference Manual for details.
*/
#define PIN_MODE_INPUT(n) (0 << ((n) * 2))
#define PIN_MODE_OUTPUT(n) (1 << ((n) * 2))
#define PIN_MODE_ALTERNATE(n) (2 << ((n) * 2))
#define PIN_MODE_ANALOG(n) (3 << ((n) * 2))
#define PIN_OTYPE_PUSHPULL(n) (0 << (n))
#define PIN_OTYPE_OPENDRAIN(n) (1 << (n))
#define PIN_OSPEED_2M(n) (0 << ((n) * 2))
#define PIN_OSPEED_25M(n) (1 << ((n) * 2))
#define PIN_OSPEED_50M(n) (2 << ((n) * 2))
#define PIN_OSPEED_100M(n) (3 << ((n) * 2))
#define PIN_PUDR_FLOATING(n) (0 << ((n) * 2))
#define PIN_PUDR_PULLUP(n) (1 << ((n) * 2))
#define PIN_PUDR_PULLDOWN(n) (2 << ((n) * 2))
#define PIN_AFIO_AF(n, v) ((v##U) << ((n % 8) * 4))
/*
* Port A setup.
* All input with pull-up except:
* PA8 - MCO 1 (alternate 0).
* PA13 - JTMS/SWDAT (alternate 0).
* PA14 - JTCK/SWCLK (alternate 0).
* PA15 - JTDI (alternate 0).
*/
#define VAL_GPIOA_MODER (PIN_MODE_ALTERNATE(8) | \
PIN_MODE_ALTERNATE(13) | \
PIN_MODE_ALTERNATE(14) | \
PIN_MODE_ALTERNATE(15))
#define VAL_GPIOA_OTYPER 0x00000000
#define VAL_GPIOA_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOA_PUPDR (PIN_PUDR_FLOATING(13) | \
PIN_PUDR_FLOATING(14) | \
PIN_PUDR_FLOATING(15))
#define VAL_GPIOA_ODR 0xFFFFFFFF
#define VAL_GPIOA_AFRL 0x00000000
#define VAL_GPIOA_AFRH 0x00000000
/*
* Port B setup.
* All input with pull-up except:
* PB3 - JTDO (alternate 0).
* PB4 - JNTRST (alternate 0).
*/
#define VAL_GPIOB_MODER (PIN_MODE_ALTERNATE(3) | \
PIN_MODE_ALTERNATE(4))
#define VAL_GPIOB_OTYPER 0x00000000
#define VAL_GPIOB_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOB_PUPDR (~(PIN_PUDR_FLOATING(3) | \
PIN_PUDR_FLOATING(4)))
#define VAL_GPIOB_ODR 0xFFFFFFFF
#define VAL_GPIOB_AFRL 0x00000000
#define VAL_GPIOB_AFRH 0x00000000
/*
* Port C setup.
* All input with pull-up except:
* PC9 - MCO2 (alternate 0).
* PC10 - USART3_TX (alternate 7).
* PC11 - USART3_RX (alternate 7).
* PC14 - OSC32_INT (input floating).
* PC15 - OSC32_OUT (input floating).
*/
#define VAL_GPIOC_MODER (PIN_MODE_ALTERNATE(9) | \
PIN_MODE_ALTERNATE(10) | \
PIN_MODE_ALTERNATE(11))
#define VAL_GPIOC_OTYPER 0x00000000
#define VAL_GPIOC_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOC_PUPDR (~(PIN_PUDR_PULLUP(11) | \
PIN_PUDR_FLOATING(14) | \
PIN_PUDR_FLOATING(15)))
#define VAL_GPIOC_ODR 0xFFFFFFFF
#define VAL_GPIOC_AFRL 0x00000000
#define VAL_GPIOC_AFRH (PIN_AFIO_AF(7, 10) | \
PIN_AFIO_AF(7, 11))
/*
* Port D setup.
* All input with pull-up.
*/
#define VAL_GPIOD_MODER 0x00000000
#define VAL_GPIOD_OTYPER 0x00000000
#define VAL_GPIOD_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOD_PUPDR 0xFFFFFFFF
#define VAL_GPIOD_ODR 0xFFFFFFFF
#define VAL_GPIOD_AFRL 0x00000000
#define VAL_GPIOD_AFRH 0x00000000
/*
* Port E setup.
* All input with pull-up.
*/
#define VAL_GPIOE_MODER 0x00000000
#define VAL_GPIOE_OTYPER 0x00000000
#define VAL_GPIOE_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOE_PUPDR 0xFFFFFFFF
#define VAL_GPIOE_ODR 0xFFFFFFFF
#define VAL_GPIOE_AFRL 0x00000000
#define VAL_GPIOE_AFRH 0x00000000
/*
* Port F setup.
* All input with pull-up.
*/
#define VAL_GPIOF_MODER 0x00000000
#define VAL_GPIOF_OTYPER 0x00000000
#define VAL_GPIOF_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOF_PUPDR 0xFFFFFFFF
#define VAL_GPIOF_ODR 0xFFFFFFFF
#define VAL_GPIOF_AFRL 0x00000000
#define VAL_GPIOF_AFRH 0x00000000
/*
* Port G setup.
* All input with pull-up.
*/
#define VAL_GPIOG_MODER (PIN_MODE_OUTPUT(GPIOG_LED1))
#define VAL_GPIOG_OTYPER 0x00000000
#define VAL_GPIOG_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOG_PUPDR (~(PIN_PUDR_FLOATING(GPIOG_LED1)))
#define VAL_GPIOG_ODR 0xFFFFFFBF
#define VAL_GPIOG_AFRL 0x00000000
#define VAL_GPIOG_AFRH 0x00000000
/*
* Port H setup.
* All input with pull-up.
*/
#define VAL_GPIOH_MODER 0x00000000
#define VAL_GPIOH_OTYPER 0x00000000
#define VAL_GPIOH_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOH_PUPDR 0xFFFFFFFF
#define VAL_GPIOH_ODR 0xFFFFFFFF
#define VAL_GPIOH_AFRL 0x00000000
#define VAL_GPIOH_AFRH 0x00000000
/*
* Port I setup.
* All input with pull-up.
*/
#define VAL_GPIOI_MODER 0x00000000
#define VAL_GPIOI_OTYPER 0x00000000
#define VAL_GPIOI_OSPEEDR 0xFFFFFFFF
#define VAL_GPIOI_PUPDR 0xFFFFFFFF
#define VAL_GPIOI_ODR 0xFFFFFFFF
#define VAL_GPIOI_AFRL 0x00000000
#define VAL_GPIOI_AFRH 0x00000000
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
