blob: 2193179b8cf5cc37b90d53fe802b90b7d78a6a63 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/*
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for the STMicroelectronics STM3210C-EVAL evaluation board.
*/
#define GPIOD_LED1 7
#define GPIOD_LED2 13
#define GPIOD_LED3 3
#define GPIOD_LED4 4
/*
* Board identifier.
*/
#define BOARD_ST_STM3210C_EVAL
#define BOARD_NAME "ST STM3210C-EVAL"
/*
* Board frequencies.
*/
#define STM32_LSECLK 32768
#define STM32_HSECLK 25000000
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*/
#define STM32F10X_CL
/*
* IO pins assignments.
* *********************TO BE COMPLETED*********************
*/
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input except:
*/
#define VAL_GPIOACRL 0x44444444 /* PA7...PA0 */
#define VAL_GPIOACRH 0x44444444 /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
/*
* Port B setup.
* Everything input except:
*/
#define VAL_GPIOBCRL 0x44444444 /* PB7...PB0 */
#define VAL_GPIOBCRH 0x44444444 /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup.
* Everything input except:
*/
#define VAL_GPIOCCRL 0x44444444 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x44444444 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFFFF
/*
* Port D setup.
* Everything input except:
* PD5 - USART2TX (remapped) AF PP Output
* PD6 - USART2RX (remapped) Digital Input
* PD7 - LED (LD1) PP Output
*/
#define VAL_GPIODCRL 0x34B33444 /* PD7...PD0 */
#define VAL_GPIODCRH 0x44344444 /* PD15...PD8 */
#define VAL_GPIODODR 0x0000DF67
/*
* Port E setup.
* Everything input except:
*/
#define VAL_GPIOECRL 0x44444444 /* PE7...PE0 */
#define VAL_GPIOECRH 0x44344444 /* PE15...PE8 */
#define VAL_GPIOEODR 0xFFFFFFFF
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
