diff options
Diffstat (limited to 'os')
| -rw-r--r-- | os/hal/boards/ST_EVALKITST7580_1/board.c | 53 | ||||
| -rw-r--r-- | os/hal/boards/ST_EVALKITST7580_1/board.h | 221 | ||||
| -rw-r--r-- | os/hal/boards/ST_EVALKITST7580_1/board.mk | 5 |
3 files changed, 279 insertions, 0 deletions
diff --git a/os/hal/boards/ST_EVALKITST7580_1/board.c b/os/hal/boards/ST_EVALKITST7580_1/board.c new file mode 100644 index 000000000..eed5bb874 --- /dev/null +++ b/os/hal/boards/ST_EVALKITST7580_1/board.c @@ -0,0 +1,53 @@ +/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/*
+ Concepts and parts of this file have been contributed by Rocco Marco
+ Guglielmi.
+ */
+#include "hal.h"
+
+/**
+ * @brief PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ * This variable is used by the HAL when initializing the PAL driver.
+ */
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+const PALConfig pal_default_config =
+{
+ {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
+ {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
+ {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
+ {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
+ {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
+};
+#endif
+
+/*
+ * Early initialization code.
+ * This initialization must be performed just after stack setup and before
+ * any other initialization.
+ */
+void __early_init(void) {
+
+ stm32_clock_init();
+}
+
+/*
+ * Board-specific initialization code.
+ */
+void boardInit(void) {
+}
diff --git a/os/hal/boards/ST_EVALKITST7580_1/board.h b/os/hal/boards/ST_EVALKITST7580_1/board.h new file mode 100644 index 000000000..1ff513443 --- /dev/null +++ b/os/hal/boards/ST_EVALKITST7580_1/board.h @@ -0,0 +1,221 @@ +/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+/*
+ Concepts and parts of this file have been contributed by Rocco Marco
+ Guglielmi.
+ */
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for the ST7580 Evaluation kit board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_ST_EVALKIT_ST7580
+#define BOARD_NAME "STMicroelectronics EVALKITST7580_1"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK 0
+#define STM32_HSECLK 8000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ */
+#define STM32F10X_MD
+
+/*
+ * IO pins assignments.
+ */
+#define GPIOA_CL_ADC 0
+#define GPIOA_PLC_T_REQ 1
+#define GPIOA_PLC_TXD 2
+#define GPIOA_PLC_RXD 3
+#define GPIOA_SD_NSS 4
+#define GPIOA_SD_SCLK 5
+#define GPIOA_SD_MISO 6
+#define GPIOA_SD_MOSI 7
+#define GPIOA_8MHZ_MCO 8
+#define GPIOA_UART1_TXD 9
+#define GPIOA_UART1_RXD 10
+#define GPIOA_USBDM 11
+#define GPIOA_USBDP 12
+#define GPIOA_JTMS 13
+#define GPIOA_JTCK 14
+#define GPIOA_JTDI 15
+
+#define GPIOB_SD_CD 0
+#define GPIOB_PA_ADC 1
+#define GPIOB_BOOT1 2
+#define GPIOB_J_TDO 3
+#define GPIOB_J_TRSTN 4
+#define GPIOB_LED_RED 5
+#define GPIOB_LED_YELLOW 6
+#define GPIOB_LED_GREEN 7
+#define GPIOB_I2C1_SCL 8
+#define GPIOB_I2C1_SDA 9
+#define GPIOB_SW4 10
+#define GPIOB_SW3 11
+#define GPIOB_DIP_SW4 12
+#define GPIOB_DIP_SW3 13
+#define GPIOB_DIP_SW2 14
+#define GPIOB_DIP_SW1 15
+
+#define GPIOC_PC0 0
+#define GPIOC_PC1 1
+#define GPIOC_PC2 2
+#define GPIOC_PC3 3
+#define GPIOC_PC4 4
+#define GPIOC_PC5 5
+#define GPIOC_PC6 6
+#define GPIOC_PC7 7
+#define GPIOC_PC8 8
+#define GPIOC_PC9 9
+#define GPIOC_PC10 10
+#define GPIOC_PC11 11
+#define GPIOC_PC12 12
+#define GPIOC_PL_RX_ON 13
+#define GPIOC_PL_TX_ON 14
+#define GPIOC_PLC_RESETN 15
+
+#define GPIOD_OSC_IN 0
+#define GPIOD_OSC_OUT 1
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ * 0 - Analog input.
+ * 1 - Push Pull output 10MHz.
+ * 2 - Push Pull output 2MHz.
+ * 3 - Push Pull output 50MHz.
+ * 4 - Digital input.
+ * 5 - Open Drain output 10MHz.
+ * 6 - Open Drain output 2MHz.
+ * 7 - Open Drain output 50MHz.
+ * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ * 9 - Alternate Push Pull output 10MHz.
+ * A - Alternate Push Pull output 2MHz.
+ * B - Alternate Push Pull output 50MHz.
+ * C - Reserved.
+ * D - Alternate Open Drain output 10MHz.
+ * E - Alternate Open Drain output 2MHz.
+ * F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * PA0 - Analog input (GPIOA_CL_ADC)
+ * PA1 - Push Pull output (GPIOA_PLC_T_REQ).
+ * PA2 - Alternate output (GPIOA_PLC_TXD).
+ * PA3 - Pull-up input (GPIOA_PLC_RXD).
+ * PA4 - Push Pull output (GPIOA_SD_NSS).
+ * PA5 - Alternate output (GPIOA_SD_SCLK).
+ * PA6 - Alternate output (GPIOA_SD_MISO).
+ * PA7 - Alternate output (GPIOA_SD_MOSI).
+ * PA8 - Alternate output (GPIOA_8MHZ_MCO).
+ * PA9 - Alternate output (GPIOA_UART1_TXD).
+ * PA10 - Normal input (GPIOA_UART1_RXD).
+ * PA11 - Alternate output (GPIOA_USBDM).
+ * PA12 - Alternate output (GPIOA_USBDP).
+ * PA13 - Pull-up input (GPIOA_JTMS).
+ * PA14 - Pull-down input (GPIOA_JTCK).
+ * PA15 - Pull-up input (GPIOA_JTDI).
+ */
+#define VAL_GPIOACRL 0xBBB38B30 /* PA7...PA0 */
+#define VAL_GPIOACRH 0x888BB4BB /* PA15...PA8 */
+#define VAL_GPIOAODR 0xFFFFBFFF
+
+/*
+ * Port B setup.
+ * PB0 - Pull-up input (GPIOB_SD_CD)
+ * PB1 - Analog input (GPIOB_PA_ADC).
+ * PB2 - Normal input (GPIOB_BOOT1).
+ * PB3 - Pull-up input (GPIOB_J_TDO).
+ * PB4 - Pull-up input (GPIOB_J_TRSTN).
+ * PB5 - Push Pull output (GPIOB_LED_RED).
+ * PB6 - Push Pull output (GPIOB_LED_YELLOW).
+ * PB7 - Push Pull output (GPIOB_LED_GREEN).
+ * PB8 - Alternate output (GPIOB_I2C1_SCL).
+ * PB9 - Alternate output (GPIOB_I2C1_SDA).
+ * PB10 - Normal input (GPIOB_SW4).
+ * PB11 - Normal input (GPIOB_SW3).
+ * PB12 - Normal input (GPIOB_DIP_SW4).
+ * PB13 - Normal input (GPIOB_DIP_SW3).
+ * PB14 - Normal input (GPIOB_DIP_SW2).
+ * PB15 - Normal input (GPIOB_DIP_SW1).
+ */
+#define VAL_GPIOBCRL 0x33388408 /* PB7...PB0 */
+#define VAL_GPIOBCRH 0x444444BB /* PB15...PB8 */
+#define VAL_GPIOBODR 0xFFFFFFFF
+
+/*
+ * Port C setup.
+ * Everything input with pull-up except:
+ * PC13 - Normal input (GPIOC_PL_RX_ON).
+ * PC14 - Normal input (GPIOC_PL_TX_ON).
+ * PC15 - Push Pull output (GPIOC_PLC_RESETN).
+ */
+#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
+#define VAL_GPIOCCRH 0x34488888 /* PC15...PC8 */
+#define VAL_GPIOCODR 0xFFFFFFFF
+
+/*
+ * Port D setup.
+ * Everything input with pull-up except:
+ * PD0 - Normal input (GPIOD_OSC_IN).
+ * PD1 - Normal input (GPIOD_OSC_OUT).
+ */
+#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
+#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
+#define VAL_GPIODODR 0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
+#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
+#define VAL_GPIOEODR 0xFFFFFFFF
+
+/*
+ * USB bus activation macro, required by the USB driver.
+ */
+#define usb_lld_connect_bus(usbp)
+
+/*
+ * USB bus de-activation macro, required by the USB driver.
+ */
+#define usb_lld_disconnect_bus(usbp)
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+ void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
diff --git a/os/hal/boards/ST_EVALKITST7580_1/board.mk b/os/hal/boards/ST_EVALKITST7580_1/board.mk new file mode 100644 index 000000000..48775bb9c --- /dev/null +++ b/os/hal/boards/ST_EVALKITST7580_1/board.mk @@ -0,0 +1,5 @@ +# List of all the board related files.
+BOARDSRC = ${CHIBIOS}/os/hal/boards/ST_EVALKITST7580_1/board.c
+
+# Required include directories
+BOARDINC = ${CHIBIOS}/os/hal/boards/ST_EVALKITST7580_1
|