diff options
Diffstat (limited to 'roms/u-boot/board/xes')
32 files changed, 2040 insertions, 0 deletions
diff --git a/roms/u-boot/board/xes/common/Makefile b/roms/u-boot/board/xes/common/Makefile new file mode 100644 index 00000000..65d321ab --- /dev/null +++ b/roms/u-boot/board/xes/common/Makefile @@ -0,0 +1,14 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-$(CONFIG_FSL_PCI_INIT) += fsl_8xxx_pci.o +obj-$(CONFIG_MPC8572) += fsl_8xxx_clk.o +obj-$(CONFIG_MPC86xx) += fsl_8xxx_clk.o +obj-$(CONFIG_P2020) += fsl_8xxx_clk.o +obj-$(CONFIG_MPC85xx) += fsl_8xxx_misc.o board.o +obj-$(CONFIG_MPC86xx) += fsl_8xxx_misc.o board.o +obj-$(CONFIG_NAND_ACTL) += actl_nand.o diff --git a/roms/u-boot/board/xes/common/actl_nand.c b/roms/u-boot/board/xes/common/actl_nand.c new file mode 100644 index 00000000..bf896fe0 --- /dev/null +++ b/roms/u-boot/board/xes/common/actl_nand.c @@ -0,0 +1,49 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * This driver support NAND devices which have address lines + * connected as ALE and CLE inputs. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <nand.h> +#include <asm/io.h> + +/* + * Hardware specific access to control-lines + */ +static void nand_addr_hwcontrol(struct mtd_info *mtd, int cmd, uint ctrl) +{ + struct nand_chip *this = mtd->priv; + ulong IO_ADDR_W; + + if (ctrl & NAND_CTRL_CHANGE) { + IO_ADDR_W = (ulong)this->IO_ADDR_W; + + IO_ADDR_W &= ~(CONFIG_SYS_NAND_ACTL_CLE | + CONFIG_SYS_NAND_ACTL_ALE | + CONFIG_SYS_NAND_ACTL_NCE); + if (ctrl & NAND_CLE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_CLE; + if (ctrl & NAND_ALE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_ALE; + if (ctrl & NAND_NCE) + IO_ADDR_W |= CONFIG_SYS_NAND_ACTL_NCE; + + this->IO_ADDR_W = (void *)IO_ADDR_W; + } + + if (cmd != NAND_CMD_NONE) + writeb(cmd, this->IO_ADDR_W); +} + +int board_nand_init(struct nand_chip *nand) +{ + nand->ecc.mode = NAND_ECC_SOFT; + nand->cmd_ctrl = nand_addr_hwcontrol; + nand->chip_delay = CONFIG_SYS_NAND_ACTL_DELAY; + + return 0; +} diff --git a/roms/u-boot/board/xes/common/board.c b/roms/u-boot/board/xes/common/board.c new file mode 100644 index 00000000..4ed6f50e --- /dev/null +++ b/roms/u-boot/board/xes/common/board.c @@ -0,0 +1,66 @@ +/* + * Copyright 2009 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include "fsl_8xxx_misc.h" + +int checkboard(void) +{ + char name[] = CONFIG_SYS_BOARD_NAME; + char buf[64]; + char *s; + int i; + +#ifdef CONFIG_SYS_FORM_CUSTOM + s = "Custom"; +#elif CONFIG_SYS_FORM_6U_CPCI + s = "6U CompactPCI"; +#elif CONFIG_SYS_FORM_ATCA_PMC + s = "ATCA w/PMC"; +#elif CONFIG_SYS_FORM_ATCA_AMC + s = "ATCA w/AMC"; +#elif CONFIG_SYS_FORM_VME + s = "VME"; +#elif CONFIG_SYS_FORM_6U_VPX + s = "6U VPX"; +#elif CONFIG_SYS_FORM_PMC + s = "PMC"; +#elif CONFIG_SYS_FORM_PCI + s = "PCI"; +#elif CONFIG_SYS_FORM_3U_CPCI + s = "3U CompactPCI"; +#elif CONFIG_SYS_FORM_AMC + s = "AdvancedMC"; +#elif CONFIG_SYS_FORM_XMC + s = "XMC"; +#elif CONFIG_SYS_FORM_PMC_XMC + s = "PMC/XMC"; +#elif CONFIG_SYS_FORM_PCI_EXPRESS + s = "PCI Express"; +#elif CONFIG_SYS_FORM_3U_VPX + s = "3U VPX"; +#else +#error "Form factor not defined" +#endif + + name[strlen(name) - 1] += get_board_derivative(); + printf("Board: X-ES %s %s SBC\n", name, s); + + /* Display board specific information */ + puts(" "); + i = getenv_f("board_rev", buf, sizeof(buf)); + if (i > 0) + printf("Rev %s, ", buf); + i = getenv_f("serial#", buf, sizeof(buf)); + if (i > 0) + printf("Serial# %s, ", buf); + i = getenv_f("board_cfg", buf, sizeof(buf)); + if (i > 0) + printf("Cfg %s", buf); + puts("\n"); + + return 0; +} diff --git a/roms/u-boot/board/xes/common/fsl_8xxx_clk.c b/roms/u-boot/board/xes/common/fsl_8xxx_clk.c new file mode 100644 index 00000000..2a604d44 --- /dev/null +++ b/roms/u-boot/board/xes/common/fsl_8xxx_clk.c @@ -0,0 +1,54 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> + +/* + * Return SYSCLK input frequency - 50 MHz or 66 MHz depending on POR config + */ +unsigned long get_board_sys_clk(ulong dummy) +{ +#if defined(CONFIG_MPC85xx) + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#elif defined(CONFIG_MPC86xx) + immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; + volatile ccsr_gur_t *gur = &immap->im_gur; +#endif + + if (in_be32(&gur->gpporcr) & 0x10000) + return 66666666; + else +#ifdef CONFIG_P2020 + return 100000000; +#else + return 50000000; +#endif +} + +#ifdef CONFIG_MPC85xx +/* + * Return DDR input clock - synchronous with SYSCLK or 66 MHz + * Note: 86xx doesn't support asynchronous DDR clk + */ +unsigned long get_board_ddr_clk(ulong dummy) +{ + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 ddr_ratio = (in_be32(&gur->porpllsr) & 0x00003e00) >> 9; + + if (ddr_ratio == 0x7) + return get_board_sys_clk(dummy); + +#ifdef CONFIG_P2020 + if (in_be32(&gur->gpporcr) & 0x20000) + return 66666666; + else + return 100000000; +#else + return 66666666; +#endif +} +#endif diff --git a/roms/u-boot/board/xes/common/fsl_8xxx_misc.c b/roms/u-boot/board/xes/common/fsl_8xxx_misc.c new file mode 100644 index 00000000..2899e111 --- /dev/null +++ b/roms/u-boot/board/xes/common/fsl_8xxx_misc.c @@ -0,0 +1,44 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> +#ifdef CONFIG_PCA953X +#include <pca953x.h> + +/* + * Determine if a board's flashes are write protected + */ +int board_flash_wp_on(void) +{ + if (pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_NVM_WP) + return 1; + + return 0; +} +#endif + +/* + * Return a board's derivative model number. For example: + * return 2 for the XPedite5372 and return 1 for the XPedite5201. + */ +uint get_board_derivative(void) +{ +#if defined(CONFIG_MPC85xx) + volatile ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; +#elif defined(CONFIG_MPC86xx) + volatile immap_t *immap = (immap_t *)CONFIG_SYS_CCSRBAR; + volatile ccsr_gur_t *gur = &immap->im_gur; +#endif + + /* + * The top 4 lines of the local bus address are pulled low/high and + * can be read to determine the least significant digit of a board's + * model number. + */ + return gur->gpporcr >> 28; +} diff --git a/roms/u-boot/board/xes/common/fsl_8xxx_misc.h b/roms/u-boot/board/xes/common/fsl_8xxx_misc.h new file mode 100644 index 00000000..106bb233 --- /dev/null +++ b/roms/u-boot/board/xes/common/fsl_8xxx_misc.h @@ -0,0 +1,12 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __FSL_8XXX_MISC_H___ +#define __FSL_8XXX_MISC_H___ + +uint get_board_derivative(void); + +#endif /* __FSL_8XXX_MISC_H__ */ diff --git a/roms/u-boot/board/xes/common/fsl_8xxx_pci.c b/roms/u-boot/board/xes/common/fsl_8xxx_pci.c new file mode 100644 index 00000000..510f638f --- /dev/null +++ b/roms/u-boot/board/xes/common/fsl_8xxx_pci.c @@ -0,0 +1,72 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <asm/fsl_serdes.h> +#include <asm/io.h> +#include <linux/compiler.h> +#include <libfdt.h> +#include <fdt_support.h> + + +#ifdef CONFIG_PCI1 +static struct pci_controller pci1_hose; +#endif + +void pci_init_board(void) +{ + int first_free_busno = 0; + +#ifdef CONFIG_PCI1 + int pcie_ep; + struct fsl_pci_info pci_info; + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 devdisr = in_be32(&gur->devdisr); + uint pci_spd_norm = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1_SPD; + uint pci_32 = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1_PCI32; + uint pci_arb = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1_ARB; + uint pcix = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1; + uint freq = CONFIG_SYS_CLK_FREQ / 1000 / 1000; + + if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { + SET_STD_PCI_INFO(pci_info, 1); + set_next_law(pci_info.mem_phys, + law_size_bits(pci_info.mem_size), pci_info.law); + set_next_law(pci_info.io_phys, + law_size_bits(pci_info.io_size), pci_info.law); + + pcie_ep = fsl_setup_hose(&pci1_hose, pci_info.regs); + printf("PCI1: %d bit %s, %s %d MHz, %s, %s\n", + pci_32 ? 32 : 64, + pcix ? "PCIX" : "PCI", + pci_spd_norm ? ">=" : "<=", + pcix ? freq * 2 : freq, + pcie_ep ? "agent" : "host", + pci_arb ? "arbiter" : "external-arbiter"); + + first_free_busno = fsl_pci_init_port(&pci_info, + &pci1_hose, first_free_busno); + } else { + printf("PCI1: disabled\n"); + } +#elif defined CONFIG_MPC8548 + volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + /* PCI1 not present on MPC8572 */ + setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); +#endif + + fsl_pcie_init_board(first_free_busno); +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_pci_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} +#endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/roms/u-boot/board/xes/xpedite1000/Makefile b/roms/u-boot/board/xes/xpedite1000/Makefile new file mode 100644 index 00000000..308de91c --- /dev/null +++ b/roms/u-boot/board/xes/xpedite1000/Makefile @@ -0,0 +1,9 @@ +# +# (C) Copyright 2002-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = xpedite1000.o +extra-y += init.o diff --git a/roms/u-boot/board/xes/xpedite1000/README b/roms/u-boot/board/xes/xpedite1000/README new file mode 100644 index 00000000..1da8b800 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite1000/README @@ -0,0 +1,82 @@ + XES XPedite1000 Board + + Last Update: December 29, 2003 +======================================================================= + +This file contains some handy info regarding U-Boot and the XES +XPedite1000 PPC440GX PrPMC board. See the README.ppc440 for additional +information. + + +SWITCH SETTINGS & JUMPERS +========================== + +Jumpers selected for AMD29LV040B flash part as the boot flash. + + +I2C Strap EEPROM & Environment Settings +======================================= + +The XPedite1000 uses a single I2C eeprom for the 440 strappings and for +the environment variables. The first page (256 bytes) contains the +strappings and the 2 EMAC HW Ethernet addresses. Be careful not to +change the 1st page of the EEPROM! Unpopulated jumper J560 can get you +out of trouble as it disables the strapping read from EEPROM. + +I2C probe +===================== + +The i2c utilities work and have been tested on Rev B. of the 440GX. See +README.ebony for more information about i2c probing with the 440. + + +GETTING OUT OF I2C TROUBLE +=========================== + +(Direct quote from README.ebony) +If you're like me ... you may have screwed up your bootstrap serial +eeprom ... or worse, your SPD eeprom when experimenting with the +i2c commands. If so, here are some ideas on how to get out of +trouble: + +Serial bootstrap eeprom corruption: +----------------------------------- +Power down the board and set the following straps: + +J560 - closed + +This will select the default sys0 and sys1 settings (the serial +eeproms are not used). Then power up the board and fix the serial +eeprom using the 'i2c mm' command. Here are the values I currently +use: + +=> i2c md 50 0 10 + +0000: 85 7d 42 06 07 80 11 00 00 00 00 00 00 00 00 00 .}B............. + +Once you have the eeproms set correctly change the +J560 straps as you desire. + + +PPC440GX Ethernet EMACs +======================= + +The XES XPedite1000 uses emac 2 & 3 and ignores emac 0 & 1. PHYs are connected +only to emac 2 & 3. The HW Ethernet addresses are read from the i2c eeprom and +placed in the bd info structure for enet2addr and enet3addr. The ethernet driver +senses that enetaddr and enet1addr are 0's and does not use them. + +As of this writing gigabit ethernet and the TCPIP acceleration hardware is not +supported. + + +Flash Support +============= + +As of this writing, there is support for the 1/2mb boot flash only. User flash +is not yet supported. + + +Regards, +--Travis +<travis.sawyer@sandburst.com> diff --git a/roms/u-boot/board/xes/xpedite1000/config.mk b/roms/u-boot/board/xes/xpedite1000/config.mk new file mode 100644 index 00000000..ec7651e4 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite1000/config.mk @@ -0,0 +1,20 @@ +# +# (C) Copyright 2002-2004 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +# +# XES XPedite1000 PPC440GX +# + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 +endif diff --git a/roms/u-boot/board/xes/xpedite1000/init.S b/roms/u-boot/board/xes/xpedite1000/init.S new file mode 100644 index 00000000..9708ecc8 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite1000/init.S @@ -0,0 +1,33 @@ +/* +* Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> + * SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <ppc_asm.tmpl> +#include <asm/mmu.h> +#include <config.h> +#include <asm/ppc4xx.h> + +/* + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + */ + + .section .bootpg,"ax" + .globl tlbtab + +tlbtab: + tlbtab_start + tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 1, AC_RWX | SA_IG) + tlbentry( CONFIG_SYS_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_RW | SA_IG) + tlbentry( CONFIG_SYS_ISRAM_BASE, SZ_256K, 0x80000000, 0, AC_RWX | SA_IG) + tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_RWX | SA_IG ) + tlbentry( CONFIG_SYS_SDRAM_BASE+0x10000000, SZ_256M, 0x10000000, 0, AC_RWX | SA_IG ) + tlbentry( CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 2, AC_RW | SA_IG ) + tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_RW | SA_IG ) + tlbtab_end diff --git a/roms/u-boot/board/xes/xpedite1000/u-boot.lds.debug b/roms/u-boot/board/xes/xpedite1000/u-boot.lds.debug new file mode 100644 index 00000000..04089ae7 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite1000/u-boot.lds.debug @@ -0,0 +1,126 @@ +/* + * (C) Copyright 2002-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +OUTPUT_ARCH(powerpc) +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + arch/powerpc/cpu/ppc4xx/start.o (.text) + board/xes/xpedite1000/init.o (.text) + arch/powerpc/cpu/ppc4xx/kgdb.o (.text) + arch/powerpc/cpu/ppc4xx/traps.o (.text) + arch/powerpc/cpu/ppc4xx/interrupts.o (.text) + arch/powerpc/cpu/ppc4xx/4xx_uart.o (.text) + arch/powerpc/cpu/ppc4xx/cpu_init.o (.text) + arch/powerpc/cpu/ppc4xx/speed.o (.text) + common/dlmalloc.o (.text) + lib/crc32.o (.text) + arch/powerpc/lib/extable.o (.text) + lib/zlib.o (.text) + +/* common/env_embedded.o(.text) */ + + *(.text) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.eh_frame) + *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + + . = ALIGN(4); + .u_boot_list : { + KEEP(*(SORT(.u_boot_list*))); + } + + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + __bss_end = . ; + PROVIDE (end = .); +} diff --git a/roms/u-boot/board/xes/xpedite1000/xpedite1000.c b/roms/u-boot/board/xes/xpedite1000/xpedite1000.c new file mode 100644 index 00000000..daab578f --- /dev/null +++ b/roms/u-boot/board/xes/xpedite1000/xpedite1000.c @@ -0,0 +1,184 @@ +/* + * Copyright (C) 2003 Travis B. Sawyer <travis.sawyer@sandburst.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/processor.h> +#include <spd_sdram.h> +#include <i2c.h> +#include <net.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + unsigned long sdrreg; + + /* + * Enable GPIO for pins 18 - 24 + * 18 = SEEPROM_WP + * 19 = #M_RST + * 20 = #MONARCH + * 21 = #LED_ALARM + * 22 = #LED_ACT + * 23 = #LED_STATUS1 + * 24 = #LED_STATUS2 + */ + mfsdr(SDR0_PFC0, sdrreg); + mtsdr(SDR0_PFC0, (sdrreg & ~SDR0_PFC0_TRE_ENABLE) | 0x00003e00); + out32(CONFIG_SYS_GPIO_BASE + 0x018, (USR_LED0 | USR_LED1 | USR_LED2 | USR_LED3)); + LED0_OFF(); + LED1_OFF(); + LED2_OFF(); + LED3_OFF(); + + /* Setup the external bus controller/chip selects */ + mtebc(PB0AP, 0x04055200); /* 16MB Strata FLASH */ + mtebc(PB0CR, 0xff098000); /* BAS=0xff0 16MB R/W 8-bit */ + mtebc(PB1AP, 0x04055200); /* 512KB Socketed AMD FLASH */ + mtebc(PB1CR, 0xfe018000); /* BAS=0xfe0 1MB R/W 8-bit */ + mtebc(PB6AP, 0x05006400); /* 32-64MB AMD MirrorBit FLASH */ + mtebc(PB6CR, 0xf00da000); /* BAS=0xf00 64MB R/W i6-bit */ + mtebc(PB7AP, 0x05006400); /* 32-64MB AMD MirrorBit FLASH */ + mtebc(PB7CR, 0xf40da000); /* BAS=0xf40 64MB R/W 16-bit */ + + /* + * Setup the interrupt controller polarities, triggers, etc. + * + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + mtdcr(UIC1ER, 0x00000000); /* disable all */ + mtdcr(UIC1CR, 0x00000003); /* SMI & UIC1 crit are critical */ + mtdcr(UIC1PR, 0xfffffe00); /* per ref-board manual */ + mtdcr(UIC1TR, 0x01c00000); /* per ref-board manual */ + mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + + mtdcr(UIC2SR, 0xffffffff); /* clear all */ + mtdcr(UIC2ER, 0x00000000); /* disable all */ + mtdcr(UIC2CR, 0x00000000); /* all non-critical */ + mtdcr(UIC2PR, 0xffffc0ff); /* per ref-board manual */ + mtdcr(UIC2TR, 0x00ff8000); /* per ref-board manual */ + mtdcr(UIC2VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC2SR, 0xffffffff); /* clear all */ + + mtdcr(UIC3SR, 0xffffffff); /* clear all */ + mtdcr(UIC3ER, 0x00000000); /* disable all */ + mtdcr(UIC3CR, 0x00000000); /* all non-critical */ + mtdcr(UIC3PR, 0xffffffff); /* per ref-board manual */ + mtdcr(UIC3TR, 0x00ff8c0f); /* per ref-board manual */ + mtdcr(UIC3VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC3SR, 0xffffffff); /* clear all */ + + mtdcr(UIC0SR, 0xfc000000); /* clear all */ + mtdcr(UIC0ER, 0x00000000); /* disable all */ + mtdcr(UIC0CR, 0x00000000); /* all non-critical */ + mtdcr(UIC0PR, 0xfc000000); /* */ + mtdcr(UIC0TR, 0x00000000); /* */ + mtdcr(UIC0VR, 0x00000001); /* */ + + LED0_ON(); + + return 0; +} + +int checkboard(void) +{ + char buf[64]; + int i; + + printf("Board: X-ES %s PMC SBC\n", CONFIG_SYS_BOARD_NAME); + printf(" "); + i = getenv_f("board_rev", buf, sizeof(buf)); + if (i > 0) + printf("Rev %s, ", buf); + i = getenv_f("serial#", buf, sizeof(buf)); + if (i > 0) + printf("Serial# %s, ", buf); + i = getenv_f("board_cfg", buf, sizeof(buf)); + if (i > 0) + printf("Cfg %s", buf); + printf("\n"); + + return 0; +} + +phys_size_t initdram(int board_type) +{ + return spd_sdram(); +} + +/* + * Override weak pci_pre_init() + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + */ +#if defined(CONFIG_PCI) +int pci_pre_init(struct pci_controller * hose) +{ + unsigned long strap; + + /* See if we're supposed to setup the pci */ + mfsdr(SDR0_SDSTP1, strap); + if ((strap & 0x00010000) == 0) + return 0; + +#if defined(CONFIG_SYS_PCI_FORCE_PCI_CONV) + /* Setup System Device Register PCIL0_XCR */ + mfsdr(SDR0_XCR, strap); + strap &= 0x0f000000; + mtsdr(SDR0_XCR, strap); +#endif + + return 1; +} +#endif /* defined(CONFIG_PCI) */ + +#if defined(CONFIG_PCI) +/* + * Override weak is_pci_host() + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + */ +int is_pci_host(struct pci_controller *hose) +{ + return ((in32(CONFIG_SYS_GPIO_BASE + 0x1C) & 0x00000800) == 0); +} +#endif /* defined(CONFIG_PCI) */ + +#ifdef CONFIG_POST +/* + * Returns 1 if keys pressed to start the power-on long-running tests + * Called from board_init_f(). + */ +int post_hotkeys_pressed(void) +{ + return ctrlc(); +} +#endif diff --git a/roms/u-boot/board/xes/xpedite517x/Makefile b/roms/u-boot/board/xes/xpedite517x/Makefile new file mode 100644 index 00000000..d88c3d4b --- /dev/null +++ b/roms/u-boot/board/xes/xpedite517x/Makefile @@ -0,0 +1,10 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += xpedite517x.o +obj-y += ddr.o +obj-y += law.o diff --git a/roms/u-boot/board/xes/xpedite517x/ddr.c b/roms/u-boot/board/xes/xpedite517x/ddr.c new file mode 100644 index 00000000..fd602ea7 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite517x/ddr.c @@ -0,0 +1,124 @@ +/* + * Copyright 2009 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr2_spd_eeprom_t)); +} + +/* + * There are four board-specific SDRAM timing parameters which must be + * calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths. + * Unless clock and DQ lanes are very different + * lengths (>2"), this should be set to the nominal value + * of 1/2 clock delay. + * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 4.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * PCB routing on the XPedite5170 is nearly identical to the XPedite5370 + * so we use the XPedite5370 settings as a basis for the XPedite5170. + */ + +typedef struct board_memctl_options { + uint16_t datarate_mhz_low; + uint16_t datarate_mhz_high; + uint8_t clk_adjust; + uint8_t cpo_override; + uint8_t write_data_delay; +} board_memctl_options_t; + +static struct board_memctl_options bopts_ctrl[][2] = { + { + /* Controller 0 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 9, + .write_data_delay = 2, + }, + }, + { + /* Controller 1 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 7, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; + sys_info_t sysinfo; + int i; + unsigned int datarate; + + get_sys_info(&sysinfo); + datarate = get_ddr_freq(0) / 1000000; + + for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { + if ((bopts[i].datarate_mhz_low <= datarate) && + (bopts[i].datarate_mhz_high >= datarate)) { + debug("controller %d:\n", ctrl_num); + debug(" clk_adjust = %d\n", bopts[i].clk_adjust); + debug(" cpo = %d\n", bopts[i].cpo_override); + debug(" write_data_delay = %d\n", + bopts[i].write_data_delay); + popts->clk_adjust = bopts[i].clk_adjust; + popts->cpo_override = bopts[i].cpo_override; + popts->write_data_delay = bopts[i].write_data_delay; + } + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/roms/u-boot/board/xes/xpedite517x/law.c b/roms/u-boot/board/xes/xpedite517x/law.c new file mode 100644 index 00000000..2aad5d25 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite517x/law.c @@ -0,0 +1,28 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_NAND_BASE + /* NAND LAW covers 2 NAND flashes */ + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_512K, LAW_TRGT_IF_LBC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/roms/u-boot/board/xes/xpedite517x/xpedite517x.c b/roms/u-boot/board/xes/xpedite517x/xpedite517x.c new file mode 100644 index 00000000..b7ad3495 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite517x/xpedite517x.c @@ -0,0 +1,79 @@ +/* + * Copyright 2009 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/processor.h> +#include <fsl_ddr_sdram.h> +#include <asm/mmu.h> +#include <asm/io.h> +#include <fdt_support.h> +#include <pca953x.h> +#include "../common/fsl_8xxx_misc.h" + +#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_PCI) +extern void ft_board_pci_setup(void *blob, bd_t *bd); +#endif + +/* + * Print out which flash was booted from and if booting from the 2nd flash, + * swap flash chip selects to maintain consistent flash numbering/addresses. + */ +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0); + + flash_cs_fixup(); + + return 0; +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size = fsl_ddr_sdram(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* Initialize and enable DDR ECC */ + ddr_enable_ecc(dram_size); +#endif + + return dram_size; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif diff --git a/roms/u-boot/board/xes/xpedite520x/Makefile b/roms/u-boot/board/xes/xpedite520x/Makefile new file mode 100644 index 00000000..14841b9c --- /dev/null +++ b/roms/u-boot/board/xes/xpedite520x/Makefile @@ -0,0 +1,13 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2004 Freescale Semiconductor. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += xpedite520x.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/roms/u-boot/board/xes/xpedite520x/ddr.c b/roms/u-boot/board/xes/xpedite520x/ddr.c new file mode 100644 index 00000000..5c5eadc9 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite520x/ddr.c @@ -0,0 +1,71 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include <common.h> +#include <i2c.h> + +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t)); + + /* We use soldered memory, but use an SPD EEPROM to describe it. + * The SPD has an unspecified dimm type, but the DDR2 initialization + * code requires a specific type to be specified. This sets the type + * as a standard unregistered SO-DIMM. */ + if (spd->dimm_type == 0) { + spd->dimm_type = 0x4; + ((uchar *)spd)[63] += 0x4; + } +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * Factors to consider for clock adjust: + * - number of chips on bus + * - position of slot + * - DDR1 vs. DDR2? + * - ??? + * + * This needs to be determined on a board-by-board basis. + * 0110 3/4 cycle late + * 0111 7/8 cycle late + */ + popts->clk_adjust = 7; + + /* + * Factors to consider for CPO: + * - frequency + * - ddr1 vs. ddr2 + */ + popts->cpo_override = 9; + + /* + * Factors to consider for write data delay: + * - number of DIMMs + * + * 1 = 1/4 clock delay + * 2 = 1/2 clock delay + * 3 = 3/4 clock delay + * 4 = 1 clock delay + * 5 = 5/4 clock delay + * 6 = 3/2 clock delay + */ + popts->write_data_delay = 3; + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/roms/u-boot/board/xes/xpedite520x/law.c b/roms/u-boot/board/xes/xpedite520x/law.c new file mode 100644 index 00000000..05524077 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite520x/law.c @@ -0,0 +1,27 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */ + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/roms/u-boot/board/xes/xpedite520x/tlb.c b/roms/u-boot/board/xes/xpedite520x/tlb.c new file mode 100644 index 00000000..a8e1f480 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite520x/tlb.c @@ -0,0 +1,69 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + +#if CONFIG_PCI1 + /* *I*G* - PCI MEM */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), +#endif + +#if CONFIG_PCI2 + /* *I*G* - PCI MEM */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI2_MEM_PHYS, CONFIG_SYS_PCI2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCI1) || defined(CONFIG_PCI2) + /* *I*G* - PCI IO */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_IO_PHYS, CONFIG_SYS_PCI1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_16M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/roms/u-boot/board/xes/xpedite520x/xpedite520x.c b/roms/u-boot/board/xes/xpedite520x/xpedite520x.c new file mode 100644 index 00000000..aa9e99d1 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite520x/xpedite520x.c @@ -0,0 +1,80 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <asm/mmu.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_FLASH_PASS_CS)); + printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif diff --git a/roms/u-boot/board/xes/xpedite537x/Makefile b/roms/u-boot/board/xes/xpedite537x/Makefile new file mode 100644 index 00000000..2dca0d75 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite537x/Makefile @@ -0,0 +1,13 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += xpedite537x.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/roms/u-boot/board/xes/xpedite537x/ddr.c b/roms/u-boot/board/xes/xpedite537x/ddr.c new file mode 100644 index 00000000..56b5a187 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite537x/ddr.c @@ -0,0 +1,234 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> + +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr2_spd_eeprom_t)); +} + +/* + * There are four board-specific SDRAM timing parameters which must be + * calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths. + * Unless clock and DQ lanes are very different + * lengths (>2"), this should be set to the nominal value + * of 1/2 clock delay. + * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 4.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite5370 DDR2-600 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps + * = 3808ps + * = 3.808ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps + * = 6240ps + * = 6.240ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps + * = 3288ps + * = 3.288ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps + * = 5536ps + * = 5.536ns + * + * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target) + * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target) + * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7) + * + * + * ====== XPedite5370 DDR2-800 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps + * = 3341ps + * = 3.341ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps + * = 5673ps + * = 5.673ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps + * = 2822ps + * = 2.822ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps + * = 4968ps + * = 4.968ns + * + * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target) + * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9) + * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target) + * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * + * Write latency (WR_DATA_DELAY) is calculated by doing the following: + * + * The DDR SDRAM specification requires DQS be received no sooner than + * 75% of an SDRAM clock period—and no later than 125% of a clock + * period—from the capturing clock edge of the command/address at the + * SDRAM. + * + * Based on the above tracelengths, the following are calculated: + * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns + * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns + * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns + * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns + * + * Difference in arrival time CLK vs. DQS: + * Ch. 0 0.072ns + * Ch. 1 0.138ns + * + * Both of these values are much less than 25% of the clock + * period at DDR2-600 or DDR2-800, so no additional delay is needed over + * the 1/2 cycle which normally aligns the first DQS transition + * exactly WL (CAS latency minus one cycle) after the CAS strobe. + * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's + * terminology corresponds to exactly one clock period delay after + * the CAS strobe. (due to the fact that the "delay" is referenced + * from the *falling* edge of the CLK, just after the rising edge + * which the CAS strobe is latched on. + */ + +typedef struct board_memctl_options { + uint16_t datarate_mhz_low; + uint16_t datarate_mhz_high; + uint8_t clk_adjust; + uint8_t cpo_override; + uint8_t write_data_delay; +} board_memctl_options_t; + +static struct board_memctl_options bopts_ctrl[][2] = { + { + /* Controller 0 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 9, + .write_data_delay = 2, + }, + }, + { + /* Controller 1 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 7, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; + sys_info_t sysinfo; + int i; + unsigned int datarate; + + get_sys_info(&sysinfo); + datarate = sysinfo.freq_ddrbus / 1000 / 1000; + + for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { + if ((bopts[i].datarate_mhz_low <= datarate) && + (bopts[i].datarate_mhz_high >= datarate)) { + debug("controller %d:\n", ctrl_num); + debug(" clk_adjust = %d\n", bopts[i].clk_adjust); + debug(" cpo = %d\n", bopts[i].cpo_override); + debug(" write_data_delay = %d\n", + bopts[i].write_data_delay); + popts->clk_adjust = bopts[i].clk_adjust; + popts->cpo_override = bopts[i].cpo_override; + popts->write_data_delay = bopts[i].write_data_delay; + } + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/roms/u-boot/board/xes/xpedite537x/law.c b/roms/u-boot/board/xes/xpedite537x/law.c new file mode 100644 index 00000000..092c9ac1 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite537x/law.c @@ -0,0 +1,26 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/roms/u-boot/board/xes/xpedite537x/tlb.c b/roms/u-boot/board/xes/xpedite537x/tlb.c new file mode 100644 index 00000000..6d83f859 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite537x/tlb.c @@ -0,0 +1,83 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + + /* **M** - Boot page for secondary processors */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 3, BOOKE_PAGESZ_4K, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_64M, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/roms/u-boot/board/xes/xpedite537x/xpedite537x.c b/roms/u-boot/board/xes/xpedite537x/xpedite537x.c new file mode 100644 index 00000000..efd563b2 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite537x/xpedite537x.c @@ -0,0 +1,82 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif diff --git a/roms/u-boot/board/xes/xpedite550x/Makefile b/roms/u-boot/board/xes/xpedite550x/Makefile new file mode 100644 index 00000000..1a3fe763 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite550x/Makefile @@ -0,0 +1,10 @@ +# +# Copyright 2007-2008 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += xpedite550x.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/roms/u-boot/board/xes/xpedite550x/ddr.c b/roms/u-boot/board/xes/xpedite550x/ddr.c new file mode 100644 index 00000000..0c0605e3 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite550x/ddr.c @@ -0,0 +1,136 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> + +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void get_spd(ddr3_spd_eeprom_t *spd, u8 i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr3_spd_eeprom_t)); +} + +/* + * There are traditionally three board-specific SDRAM timing parameters + * which must be calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 3.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite550x DDR3-800 read delay calculations ====== + * + * The P2020 processor provides an autoleveling option. Setting CPO to + * 0x1f enables this auto configuration. + */ + +typedef struct { + unsigned short datarate_mhz_low; + unsigned short datarate_mhz_high; + unsigned char clk_adjust; + unsigned char cpo; +} board_specific_parameters_t; + +const board_specific_parameters_t board_specific_parameters[][20] = { + { + /* Controller 0 */ + { + /* DDR3-600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo = 31, + }, + { + /* DDR3-800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo = 31, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const board_specific_parameters_t *pbsp = + &(board_specific_parameters[ctrl_num][0]); + u32 num_params = sizeof(board_specific_parameters[ctrl_num]) / + sizeof(board_specific_parameters[0][0]); + u32 i; + ulong ddr_freq; + + /* + * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in + * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If + * there are two dimms in the controller, set odt_rd_cfg to 3 and + * odt_wr_cfg to 3 for the even CS, 0 for the odd CS. + */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i&1) { /* odd CS */ + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 0; + } else { /* even CS */ + if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) { + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 4; + } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) { + popts->cs_local_opts[i].odt_rd_cfg = 3; + popts->cs_local_opts[i].odt_wr_cfg = 3; + } + } + } + + /* + * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + + for (i = 0; i < num_params; i++) { + if (ddr_freq >= pbsp->datarate_mhz_low && + ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->cpo_override = pbsp->cpo; + popts->twot_en = 0; + break; + } + pbsp++; + } + + if (i == num_params) { + printf("Warning: board specific timing not found " + "for data rate %lu MT/s!\n", ddr_freq); + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + + /* + * Enable on-die termination. + * From the Micron Technical Node TN-41-04, RTT_Nom should typically + * be 30 to 40 ohms, while RTT_WR should be 120 ohms. Setting RTT_WR + * is handled in the Freescale DDR3 driver. Set RTT_Nom here. + */ + popts->rtt_override = 1; + popts->rtt_override_value = 3; +} diff --git a/roms/u-boot/board/xes/xpedite550x/law.c b/roms/u-boot/board/xes/xpedite550x/law.c new file mode 100644 index 00000000..1a3e91b9 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite550x/law.c @@ -0,0 +1,26 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/roms/u-boot/board/xes/xpedite550x/tlb.c b/roms/u-boot/board/xes/xpedite550x/tlb.c new file mode 100644 index 00000000..0bcb9306 --- /dev/null +++ b/roms/u-boot/board/xes/xpedite550x/tlb.c @@ -0,0 +1,82 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + + /* **M** - Boot page for secondary processors */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 3, BOOKE_PAGESZ_4K, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_64M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/roms/u-boot/board/xes/xpedite550x/xpedite550x.c b/roms/u-boot/board/xes/xpedite550x/xpedite550x.c new file mode 100644 index 00000000..e64d682a --- /dev/null +++ b/roms/u-boot/board/xes/xpedite550x/xpedite550x.c @@ -0,0 +1,82 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif |